Vibration damper, crankshaft, front. Revulcanizing service for rubber cushion elements.
This six (6) piece Front Door Vent Window Set contains the upper and lower seals that cover the top, front, and bottom of the vent window as well as the division post seals.
This four (4) piece Front Door Vent Window Weatherstrip Set contains the upper and lower seals that cover the top, front, and bottom of the vent window. All of the pieces are designed from original parts for a precise, factory fit.
Strap, door check. T-type, special heavy duty construction of rubber with multiple ply webbing and molded-in steel crossbar. Full length as original with one eighth (1/8) inch by seven eighths (7/8) inch steel crossbar.
Guard strip, hood to cowl. Brass core with molded integral hood rest.Length: 14.875 inches.
Insulator, motor support, rear assembly. Revulcanization service only.
Weatherstrip, convertible top to side windows. Fifteen sixteenths (15/16) inch by five eighths (5/8) inch. Sold in twelve (12) foot strips only.
Motor mount, motor stabilizer bracket, right hand side. Revulcanization service only.
This Headlight Mounting Pad is designed from the original part for superior fitment and seal. Made with a metal core. This pad acts as the headlight adjusting collar.
12 (twelve) foot strip of windshield weatherstrip channel. Seals windshield glass to body and protects interior of vehicle.
Motor mount stabilizer bracket. Revulcanization service. Send in core and allow three weeks for service.
Pads, rear axle rebound.Length: 5.125 inches. Width: 1.4375 inches.
Pads, front axle rebound. Correct shape and design like original.Length: 3.625 inches. Width: 2.125 inches. Height: 2.125 inches.
Grommets, front bumper support bar to body. Fully molded rubber. Four and five eighths inch (4-5/8") outside length by two and five eighths inch (2-5/8") outside width by one and five sixteenths inch (1-5/16") inside hole length by one and five sixteenths
This Swing-Out Windshield Weatherstrip comes in a twelve (12') foot strip. The seal slides into the track (channel) attached to the glass that goes all the way around the windshield and creates a seal when the glass is pressed against the body of the vehicle.
Liner, front fender to running board. Reversible right and left replacement. Length: 15.50 inches.
Liner, running board to body, (side apron to body seal). Set consists of two (2) pieces seven (7) foot long. One (1) inch width is after fold over.
Grommet, steering column to toe board. One and five eighths (1-5/8) inch hole for column. Similar to, but larger than our #30-0046-36.Length: 5.25 inches.
Grommets, sidemount carrier arm through fender. Reversible for right and left hand.Height: 4.0 inches.
Mounting pad, headlight bracket to fender. Molded right and left with proper beading and shape as original.Length: 9.375 inches.
Pads, hood corners. Right and left replacement. Brass core, integral holding tabs.Length: 3.125 inches.
Channel, rigid run, for vent window division bar. Chrome beaded edge, mohair lined steel channel to proper dimensions for window side of wing window frame.
Grommets, rear bumper support bar to body. Fully molded rubber w/ retaining flange. Three and eleven sixteenths inch (3-11/16") outside diameter by three inches (3") retaining flange outside diameter by two and three eighths inch (2-3/8") inside hole diam
Grommet, rear spare wheel carrier bracket. Two (2) per car. (Also order our #32-0355-37 separately).
Bushing, front motor support at timing gear cover. One (1) pair required per car. Sold only in pairs.
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching four (4) fenders to body. Sold in a 50 foot roll.
Pads, taillight bracket mounting, with proper beading.Length: 6.625 inches.
Pads, brake and clutch pedal, slip over type. Black and red rubber. For black only see our #30-0188-22.Length: 3.875 inches. Width: 2.875 inches.
Pads, brake and clutch pedal, slip over type. Black rubber only. For black and red (semi-automatic clutch models) see our #30-0188-89.Length: 3.875 inches.
Gaskets, headlight lens and reflector mounting. A three sixteenths (3/16) inch cross section rubber ring of proper diameter.
Grommet, gas tank inlet to wheel housing. Also used as grommet, gas tank inlet tube to wheel compartment bottom.
Knob, gearshift. Rubber only for flanged top nut on gearshift lever.
Sleeve, rear brake cable anti-rub. Six (6) piece set. One half (1/2) inch inside diameter, seven eighth (7/8) inch outside diameter.
Grommet, firewall, for ignition cable and thermometer tube. For two and one half (2-1/2) inch hole in sheet metal.
Motor crank case link ball insulator. One (1) pair per car. Sold only in pairs.
Front vent window division post seal. Fully molded with metal core and attaching tabs.
This Beltline Weatherstrip is sold as a three (3) foot pair. The beltline is used for side window inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Gasket, cowl vent. Top quality sponge of correct section, cut to sufficient length for circumference of vent cover.
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching two (2) fenders to body. Sold in a 25 foot roll.
Bumper, hood side panel center.Length: 2.125 inches. Width: .75 inches.
Bumper, inclined toe board pedal hole, carried on toe board to meet our #30-0055-24 pedal. dust cover.
Seals, brake and clutch pedal shanks, against underside of floorboard.Length: 2.5625 inches. Width: 1.75 inches.
Bowdrill cloth tape is used for covering convertible side window weatherstrip. Available in a 5 ft roll.
Bushing, shock absorber arm. Restore proper shock action.Height: 1.375 inches.
Boot, brake vacuum control valve.Height: .25 inches.
Gasket, windshield wiper transmission.Width: 2.5625 inches. Height: .8125 inches.