Runningboard matting for Model 115C only. Made from the molded runningboard matting for the 120's (our #30-0214-49).
Bushing and pin assembly cartridge. Inlox type, front wheel lower support arm inner pin. Shipped with instructions for reinstalling.Length: 5.75 inches.
Support assembly, rear motor mount. Revulcanization service only.
Bumper assembly, front suspension inside coil spring, with five sixteenths (5/16) inch threaded studs as found originally.
Bushing assembly, front wheel support; upper and outer. Inlox type cartridge bushing assembly.
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Bushing, front eye of rear spring.Length: 2.50 inches.
This windshield gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Stabilizer, fore and aft transmission to frame. A factory service part used to remedy clutch chatter. Steel core as original.Length: 7.50 inches.
Bushings, front suspension torque arm. Necessary for proper front end geometry.
Bumper assembly, front spring rebound (upper arm). Steel core, with treaded stud just like original.
Weatherstrip, door, hollow bulb seal construction to replace composite sponge and solid rubber. Retained by metal clips (not included, see our #70-0391-73).
Pads, rear axle rebound.Length: 5.125 inches. Width: 1.4375 inches.
Grommets, rear bumper. Molded right and left as original.Length: 4.875 inches. Width: 3.125 inches.
Boot, gearshift cover. For cane shifts only.Length: 4.0 inches. Width: 3.0 inches. Height: 5.125 inches.
Grommets, front bumper. Molded right and left, including retaining flange. Fully molded rubber. Three and fifteen sixteenths inch (3-15/16") outside length by two and five eighths inch (2-5/8") outside width by one and one half inch (1-1/2") inside hole l
Pedal, accelerator. Revulcanization service only. Includes new ball sockets as original, with correctly detailed tread pattern.Length: 9.625 inches.
Grommets, rear bumper. For models with luggage racks.Length: 4.125 inches. Width: 3.375 inches.
Cushions, motor support, at timing gear cover. One (1) pair required per car. Sold only in pairs.
Insulator, front coil springs.
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide, three sixteenths (3/16) inch, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty fi
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Channel, rigid run, for division bar opposite vent windows.
Pads, hood front corners. 2 rivet type.Length: 3.25 inches.
Pads, brake and clutch pedal, slip over type. Black and red rubber. For black only see our #30-0188-22.Length: 3.875 inches. Width: 2.875 inches.
Gaskets, headlight stanchion.Length: 11.25 inches.
Liner, front fender to radiator shell.Length: 6.50 inches.
Gaskets, taillight mounting. Proper type lip as original. One and eleven sixteenths (1-11/16) inch by four and one half (4-1/4) inch.Length: 4.25 inches.
Pads, brake and clutch pedal, slip over type. Black rubber only. For black and red (semi-automatic clutch models) see our #30-0188-89.Length: 3.875 inches.
Pads, trunk hinge. Four (4) piece set.
Pad, radiator lower splasher to grille. Fastens into place with rivets. One four (4) piece set required per car.Length: .875 inches. Width: .875 inches.
Grommet, fuel filler neck.
Knob, gearshift (floor shift type).
Gasket, cowl vent, original labyrinth type, not sponge.Length: 14.75 inches. Width: 5.50 inches.
Boot, brake and clutch pedal shank at toe board.Length: 2.9375 inches.
Cloth covered, mohair lined flexible metal channel for sides and top of door windows. Available in 5ft and 6ft lengths.
Weatherstrip, door window inner and outer, front and rear doors. Bend to fit. Available in a 3ft pair and 6ft piece.
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide, three sixteenths (3/16) inch, twenty five (25) foot roll. Typially used for attaching two (2) fenders to body. For f
Cloth covered mohair-lined type. For sides and top of side windows. Available in 5ft and 6ft lengths.
Bushings, rear shock link assembly. Designed to act like sleeve inside link arm.Height: .9375 inches.
Gaskets, taillight door lens. For cars without center license light. Two (2) strips eleven and one half (11-1/2) inches long each.Length: 11.5 inches.
Bushings, rear shock link, upper. Rubber sleeve construction like original.
Boot, electrical connection, generator terminal or ignition coil at engine.
Cover, battery clamp. Control unsightly sulfate buildup. Help protect the nearby metal and finish. Good copy from original part.Length: 3.5 inches.
Bumper, door side. One and one fourth (1-1/4) inch by two (2) inch.Length: 2.0 inches. Width: 1.25 inches.
Pad, door jamb.Length: 1.50 inches. Width: 1.25 inches.
Mounting gasket, windshield wiper transmission.Width: 2.5 inches.