Vibration damper, crankshaft, front. Revulcanizing service for rubber cushion elements.
Bushing and pin assembly, cartridge, Inlox type, front wheel lower support arm inner pin. Shipped with instructions for re-installing.Length: 5.75 inches.
This front door vent window weatherstrip set is a six (6) piece set that contains the upper and lower seals that cover the top, front, and bottom of the vent window as well as the division post seals.
This front door vent window weatherstrip set is a four (4) piece set that contains the upper and lower seals that cover the top, front, and bottom of the vent window. All of the pieces are designed from original parts for a precise, factory fit.
Bushing assembly, front wheel support; upper and outer. Inlox type cartridge bushing assembly.
Hose, radiator, upper. Fluted outside diameter just like original.
Bumper, front suspension (inside of coil spring). Made with three five sixteenths (5/16) inch studs as original.
Strap, door check. T-type, special heavy duty construction of rubber with multiple ply webbing and molded-in steel crossbar. Full length as original with one eighth (1/8) inch by seven eighths (7/8) inch steel crossbar.
Weatherstrip, side window. Fits metal channel. Rubber only. Twelve (12) foot strip.Length: 144.0 inches. Width: .75 inches.
Guard strip, hood to cowl. Brass core with molded integral hood rest.Length: 14.875 inches.
Pads, convertible top folding pillar (top main bow hinge), right and left, with brass core.Width: 2.75 inches.
Insulator, motor support, rear assembly. Revulcanization service only.
This windshield gasket weatherstrip comes in a ten foot (10') strip and mounts around the full perimeter of the front glass. It has the slot to accommodate the outer edge's decorative molding and the ends may require trimming and bonding for installation.
Weatherstrip, convertible top to side windows. Fifteen sixteenths (15/16) inch by five eighths (5/8) inch. Sold in twelve (12) foot strips only.
Pads, hood front corners. Large self prong type with metal core molded left and right.Length: 3.375 inches.
Bushings, front suspension torque arm. Necessary for proper front end geometry.
Bumper assembly, front suspension rebound (upper arm). Straight style with stud.
Motor mount stabilizer bracket. Revulcanization service. Send in core and allow three weeks for service.
Pads, rear axle rebound.Length: 5.125 inches. Width: 1.4375 inches.
Grommets, rear bumper. Fully molded rubber. Three and five eighths inch (3-5/8") outside diameter by one and nine sixteenths inch (1-9/16") inside hole length by three eighths inch (3/8") inside hole width by one and one half inch (1-1/2") height.
Cushion, spare wheel in fenderwell.1937: 12's only (2 pair required). 1938-39: 12's only (3 pair required).Length: 12.875 inches. Width: 3.0 inches.
Grommets, rear bumper.Length: 3.625 inches. Width: 3.3125 inches.
Liner, front fender to running board. Reversible right and left replacement. Length: 15.50 inches.
Boot, vacuum brake cylinder main rod. Accordion type, two (2) inches diameter by six (6) inches. Top quality workmanship and material.Length: 6.0 inches.
Insulator, front coil spring. Four (4) piece set.
Grommets, front bumper. Molded right and left with correct detail as originally found. Fully molded rubber. Four inches (4") outside length by three inches (3") outside width by one and nine sixteenths inch (1-9/16") inside hole length by one half inch (1
Boot vacuum clutch cylinder rod.Length: 4.0 inches.
Bearings, stabilizer rear rod. Requires two (2) per car. Fully molded rubber. Two and one fourth inch (2 1/4") length by one and thirteen sixteenths inch (1 13/16") width by eleven sixteenths inch (11/16") inside hole diameter by two and one eighths inch
Sleeve, plug wire tube to distributor cap. One (1) pair required per car.Height: .9375 inches.
Channel, rigid run, for vent window division bar. Chrome beaded edge, mohair lined steel channel to proper dimensions for window side of wing window frame.
Bearings, stabilizer front rod. Requires two (2) per car. Fully molded rubber. Two and one fourth inch (2 1/4") length by one and thirteen sixteenths inch (1 13/16") width by nine sixteenths inch (9/16") inside hole diameter by two and one eighths inch (2
Seal, gearshift to floorboard.Length: 5.625 inches. Width: 4.875 inches.
Grommet, rear spare wheel carrier bracket. Two (2) per car. (Also order our #32-0355-37 separately).
Grommet, steering column.Length: 5.625 inches.
Bushing, front motor support at timing gear cover. One (1) pair required per car. Sold only in pairs.
Pads, headlight bracket mounting to fender. Molded left and right. Proper construction with beading as original. Sold in complete pairs only.Length: 9.
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide, three sixteenths (3/16) inch, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty fi
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Grommets, sidemount to fender.
Pads, brake and clutch pedal, slip over type. Black and red rubber. For black only see our #30-0188-22.Length: 3.875 inches. Width: 2.875 inches.
Pad, convertible top removable center pillar.Length: 3.0625 inches. Width: 2.1875 inches.
Pads, brake and clutch pedal, slip over type. Black rubber only. For black and red (semi-automatic clutch models) see our #30-0188-89.Length: 3.875 inches.
Gaskets, headlight lens and reflector mounting. A three sixteenths (3/16) inch cross section rubber ring of proper diameter.
Pads, rumbleseat step.
Grommet, fuel filler neck to fender.
Pads, trunk hinge. Four (4) piece set.
Grommet, firewall, for ignition cable and thermometer tube. For two and one half (2-1/2) inch hole in sheet metal.
Motor crank case link ball insulator. One (1) pair per car. Sold only in pairs.
Front vent window division post seal. Fully molded with metal core and attaching tabs.