Front suspension bushing
p/n: 30-0239-32
Bushings, front suspension torque arm. Necessary for proper front end geometry.
Fuel Tank Support Pad
p/n: 30-0482-41
This Fuel Tank Support Pad is made of a high quality EPDM dense rubber. This cushion is used to help reduce noise. Available by the foot.
Gearshift Seal
p/n: 30-0165-24
Seal, gearshift to floorboard.Length: 5.625 inches. Width: 4.875 inches.
Headlight Lens Gasket
p/n: 30-0176-14
Gaskets, headlight lens and reflector mounting. A three sixteenths (3/16) inch cross section rubber ring of proper diameter.
Hood Corner Pad
p/n: 30-0088-42
Pad, hood front corner. Metal core, retained by four (4) tabs.Length: 3.25 inches. Width: 1.25 inches.
Hood to Cowl Bumpers
p/n: 30-0223-42
Bumpers, hood to cowl. Brass core, one and one half (1-1/2) inch by four and one half (4-1/2) inch.Length: 4.50 inches. Width: 1.50 inches.
Insulator
p/n: 30-0404-48
Insulator, used on various places on vehicle. Uses 10 to 14 per car running board to frame bracket. Replaces factory #324851.
Lock cylinder gasket
p/n: 30-0389-71
Gasket, door lock handle escutcheon, front and rear doors. Two (2) or four (4) required per car.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
Peel-N-Stick Trunk Weatherstrip
p/n: 30-0356-WT
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.
Prop shaft retainer bushing
p/n: 70-2268-27
Retainer, intermediate bearing. All models with two piece driveshafts.
Rear Bumper Grommet
p/n: 30-0067-29
Grommets, rear bumper. Length: 4.3125 inches. Width: 2.6875 inches.
Rear Bumper Grommet
p/n: 30-0006-29
Grommets, rear bumper.Length: 3.625 inches. Width: 3.3125 inches.
Rear Window Gasket
p/n: 30-0479-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Red Brake and Clutch Pedal Pad
p/n: 30-0188-89
Pads, brake and clutch pedal, slip over type. Black and red rubber. For black only see our #30-0188-22.Length: 3.875 inches. Width: 2.875 inches.
Rigid Run Channel
p/n: 30-0180-57
Channel, rigid run, for vent window division bar. Chrome beaded edge, mohair lined steel channel to proper dimensions for window side of wing window frame.
Rumble Seat Step Mounting Pad
p/n: 30-0181-44
Pad, rumble seat step bracket to fender. Four and one fourth (4-1/4) inch long.Length: 4.375 inches.
Shock Absorber Arm Bushing
p/n: 30-0192-32
Bushing, shock absorber arm. Restore proper shock action.Height: 1.375 inches.
Shock and Sway Bar Grommet
p/n: 30-0193-33
Grommet, rear shock arm link (lower end), or rear sway bar link lower end. Shock arms used four (4) per car. If needed, sway bar used two (2) per car. Fully molded rubber.