Vibration damper, crankshaft, front. Revulcanizing service for rubber cushion elements.
These Front Door Vent Window Weatherstrips are designed from the original parts for superior fitment and seal. The pieces are molded as left and right and are one piece with the division post seal.
Bushing and pin assembly cartridge. Inlox type, front wheel lower support arm inner pin. Shipped with instructions for reinstalling.Length: 5.75 inches.
Bumper, front suspension (inside of coil spring). Made with three five sixteenths (5/16) inch studs as original.
Bushing assembly, front wheel support; upper and outer. Inlox type cartridge bushing assembly.
Strap, door check. T-type, special heavy duty construction of rubber with multiple ply webbing and molded-in steel crossbar. Full length as original with one eighth (1/8) inch by seven eighths (7/8) inch steel crossbar.
This rear window gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
This Windshield Gasket mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation. It also has the slot to accommodate the outer edge's decorative molding.
Bumpers, hood to cowl. Brass core, one and one half (1-1/2) inch by four and one half (4-1/2) inch.Length: 4.50 inches. Width: 1.50 inches.
Insulator, motor support, rear assembly. Revulcanization service only.
This windshield gasket weatherstrip comes in a ten foot (10') strip and mounts around the full perimeter of the front glass. It has the slot to accommodate the outer edge's decorative molding and the ends may require trimming and bonding for installation.
Bushings, front suspension torque arm. Necessary for proper front end geometry.
Bumpers, front spring. One (1) pair required per car.
Motor mount stabilizer bracket. Revulcanization service. Send in core and allow three weeks for service.
Grommets, rear bumper. Fully molded rubber. Three and five eighths inch (3-5/8") outside diameter by one and nine sixteenths inch (1-9/16") inside hole length by three eighths inch (3/8") inside hole width by one and one half inch (1-1/2") height.
Bumper, rear frame to axle rubber. Two (2) per car.Length: 5.1875 inches. Width: 2.0625 inches.
Weatherstrip, door, front and rear. Hollow bulb seal construction in place of composite sponge and solid rubber. Held in by clips, (not included).
Grommets, rear bumper.Length: 3.625 inches. Width: 3.3125 inches.
Grommet, front bumper. Molded right and left with hollow construction as found on original.Length: 4.0 inches. Width: 2.25 inches.
Divider, windshield gasket. Replaces #235860.
Pad, hood front corner. Metal core, retained by four (4) tabs.Length: 3.25 inches. Width: 1.25 inches.
Bumpers, hood center side panel. Brass core construction like original.
Channel, rigid run, for vent window division bar. Chrome beaded edge, mohair lined steel channel to proper dimensions for window side of wing window frame.
Bearings, stabilizer front rod. Requires two (2) per car. Fully molded rubber. Two and one fourth inch (2 1/4") length by one and thirteen sixteenths inch (1 13/16") width by nine sixteenths inch (9/16") inside hole diameter by two and one eighths inch (2
Seal, gearshift to floorboard.Length: 5.625 inches. Width: 4.875 inches.
Grommets, rear bumper.Length: 4.3125 inches. Width: 2.6875 inches.
Grommet, rear spare wheel carrier bracket. Two (2) per car. (Also order our #32-0355-37 separately).
Grommet, steering column.Length: 5.625 inches.
Bushing, front motor support at timing gear cover. One (1) pair required per car. Sold only in pairs.
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching four (4) fenders to body. Sold in a 50 foot roll.
Pads, brake and clutch pedal, slip over type. Black and red rubber. For black only see our #30-0188-22.Length: 3.875 inches. Width: 2.875 inches.
Retainer, intermediate bearing. All models with two piece driveshafts.
Pads, brake and clutch pedal, slip over type. Black rubber only. For black and red (semi-automatic clutch models) see our #30-0188-89.Length: 3.875 inches.
Pads, taillight bracket mounting, with proper beading and shape. For two and one eighths (2-1/8) inch by five and one half (5-1/2) inch base.Length: 5.
Gaskets, headlight lens and reflector mounting. A three sixteenths (3/16) inch cross section rubber ring of proper diameter.
Pads, rumbleseat step.
Grommet, fuel filler neck to fender.
Bumper assembly, front door hinge, upper, stop. Two (2) per car, steel core as original.Height: .6875 inches.
Gaskets, taillight mounting, with proper beading and shape as original. For all models with center license mounting.Length: 7.125 inches.
Rubber grip, handbrake lever.Length: 4.125 inches.
Grommet instrument board cables through firewall. Oval type with masked hole for six (6) wires or cables. Necessary replacement for correct restoration.
Gasket, cowl vent. Die cut sponge with smooth curves. Excellent reproduction designed to fit in gutter and not bind when closing.Length: 15.75 inches.
Motor crank case link ball insulator. One (1) pair per car. Sold only in pairs.
Channel, flexible window run, un-beaded. Cloth covered mohair-lined type. Available in 6ft lengths.
Cloth covered, mohair lined flexible metal channel for sides and top of door windows.
This Beltline Weatherstrip is sold as a three (3) foot pair. The beltline is used for side window inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Bushing, sway bar (stabilizer lateral tube). Two (2) used per car. Fully molded rubber. Two and three sixteenths inch (2 3/16") length by one and one half inch (1 1/2") outside diameter by five eighths inch (5/8") inside hole diameter.
Filler, windshield division channel ends, upper and lower. Two (2) piece set.