Runningboard matting. Fully molded with crowned blocks. Top quality rubber, flawless detail. No splicing or butting required.
Trim strips, stainless steel, with retaining clips.
Motor mount (insulator assembly, support, rear), right and left. Revulcanization service only.
Weatherstrip, rear quarter vent window. Full swing type.
This front door vent window weatherstrip kit is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
This windshield gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit.
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
This rear window gasket set mounts around the two (2) separate back windows. They have vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Bumper, front suspension (inside of coil spring). Made with three eighths (3/8) inch stud as original.
Bushing, rear spring and shackle. One and one eighth (1-1/8) inch diameter with nine sixteenths (9/16) inch hole. One set contains twelve (12) pieces.
Bushings, front suspension torque arm. Necessary for proper front end geometry.
Insulator assembly, transmission support. Revulcanization service only. Send in your old core for service.
Bumper, rear frame to axle rubber. Two (2) per car.Length: 5.1875 inches. Width: 2.0625 inches.
Pad, accelerator pedal. Revulcanization service only.Length: 9.625 inches. Width: 1.9375 inches.
Pads, rebound, front spring. Self retaining type.
Boots, shifter relay shaft end support.
Pads, hood rear corners. High quality rubber with metal core as original.Length: 3.4375 inches. Width: 1.875 inches.
Pads, front spring bumper rebound. Self retaining type.
Grommet, steering column at toe board.Length: 4.375 inches.
Grommets, rear bumper.Length: 4.3125 inches. Width: 2.6875 inches.
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide, three sixteenths (3/16) inch, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty fi
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Insulators, front engine support at timing gear cover.
Gaskets, headlight rim (headlight door).
Heel plate to protect driver's side floor carpet. Identical to original. Only for models with carpet.
Pads, brake and clutch pedal, slip over type. Black and red rubber. For black only see our #30-0188-22.Length: 3.875 inches. Width: 2.875 inches.
Grommets, front or rear bumper. On models without trunk racks. Two (2) pair used per car if needing both front and rear bumpers. Three and five eighths inch (3-5/8") outside length by two and one fourth inch (2-1/4") outside width by one and five eighths
Retainer, intermediate bearing. All models with two piece driveshafts.
Pads, brake and clutch pedal, slip over type. Black rubber only. For black and red (semi-automatic clutch models) see our #30-0188-89.Length: 3.875 inches.
Bushing, insulator, torque arm to frame at rear. Four (4) piece set.
Bushing, insulator, front suspension lower support arm, inner. Four (4) piece set.
Bumper assembly, front door hinge, upper, stop. Two (2) per car, steel core as original.Height: .6875 inches.
Pads, hood front corner. Metal core, retained by single rivet.Length: 1.75 inches. Width: 1.375 inches.
Gaskets, taillight mounting, with proper beading and shape as original. For all models with center license mounting.Length: 7.125 inches.
Bushing, insulator, upper support arm, outer above steering knuckle support. Four (4) piece set.
Bushings, front stabilizer mounting bracket. Fully molded rubber. One and seven sixteenths inch (1 7/16") length by one and five eighths inch (1 5/8") width by five eighths inch (5/8") inside hole diameter by one and eleven sixteenths inch (1 11/16") heig
Gasket, cowl vent. Perfect reproduction, high quality, original configuration, not a sponge substitute.Length: 14.0 inches. Width: 5.75 inches.
Rubber grip, handbrake lever.Length: 4.125 inches.
Grommet instrument board cables through firewall. Oval type with masked hole for six (6) wires or cables. Necessary replacement for correct restoration.
Grommet, fuel filler neck.
Insulator, engine snubber. One four (4) piece set required per car. Sold only in complete sets.
Boot, clutch control unit governor.1940-42: Cars with Overdrive 1941-42: Cars with ElectromaticHeight: 1.125 inches.
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Boot, brake and clutch pedal shank at toe board.Length: 2.9375 inches.
Cloth covered, mohair lined flexible metal channel for sides and top of door windows. Available in 5ft and 6ft lengths.
Weatherstrip, door window inner and outer, front and rear doors. Bend to fit. Available in a 3ft pair and 6ft piece.
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide, three sixteenths (3/16) inch, twenty five (25) foot roll. Typially used for attaching two (2) fenders to body. For f