This front door vent window weatherstrip set is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Motor mount, front. Two (2) per car. Revulcanization service only.
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Bumper, rear axle. Revulcanization service only.Height: 3.5 inches.
Mounting pad, transmission (also called insulator or support pad). Revulcanization service only.Length: 5.0 inches. Width: 3.4375 inches.
Weatherstrip, hood to cowl.
Motor mount, rear. Revulcanization service only. One (1) per car.Width: 10.6875 inches.
A vulcanized windshield weatherstrip for windows without chrome reveal molding or divider bar. This windshield weatherstrip mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Pad, parking light (fender light).Width: 19.125 inches.
This windshield gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit.
Door edge weatherstrip. Two door seals. Used for the front doors on Chevrolet, Oldsmobile & Pontiac models. Also used for the front or rear doors on Buick models. If needing all four (4) door seals for Buick purchase two (2) pairs. This part is the primar
Pad, taillight mounting, right and left.Width: 10.5625 inches.
Fillers, side roof rail to front roof rail at front corner, right and left. Metal core, threaded for original screws.
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Pedal, accelerator. Black rubber. Revulcanization service only. For brown see our #70-1660-89.Length: 9.0 inches.
A Rigid Run Channel pair with bright beaded edge, mohair lined channel, die trimmed and round formed at the top. Sold in 29" pairs.
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide, three sixteenths (3/16) inch, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty fi
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Pedal, accelerator. Brown rubber. Revulcanization service only. For black see our #70-1660-40.Color:brown Length: 9.0 inches.
Seal, fenderskirt edge. Each five (5) foot long. Similar to our #20-0111-44, but thicker.Length: 60.0 inches. Width: .25 inches.
Pad, top folding post. Fastens on lower end of post with two (2) screws. Metal core, close copy.
Seal, fenderskirt edge, exact copy, trim notch for skirt lock at installation. Compare sketch with your original to be sure. Two (2), five (5) foot strips.
Bumper, hood side pilot. Four (4) piece set required per car. Steel washer vulcanized inside rubber.
Mounting pad, trunk ornament, excellent material and workmanship.Width: 11.8125 inches.
Bumper, door side. Square type held by four (4) screws, metal core as original.
Grommets, front bumper. Fully molded rubber. Five and three fourths inch (5-3/4") outside length by two and thirteen sixteenths inch (2-13/16") outside width by one and eleven sixteenths inch (1-11/16") inside hole length by nine sixteenths inch (9/16") i
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt. 5/16"-24NF x 7-5/8" long. Includes metal sleeves, cup washers and rubber grommets.
Bushings, front stabilizer bar mounting. Fits original bracket. Fully molded rubber. One and five eighths inch (1 5/8") length by one and three eighths inch (1 3/8") outside diameter by eleven sixteenths inch (11/16") inside hole diameter.
Bushings, rear stabilizer bar mounting. Fully molded rubber. One and one half inch (1 1/2") length by one and one fourth inch (1 1/4" outside diameter by nine sixteenths inch (9/16") inside hole diameter.
This Clutch Equalizer Bushing and Seal set is designed from the original part for superior fitment and operation. The set includes a metal sleeved rubber bushing and two (2) molded rubber seals for each end of equalizer shaft.
Bulb type seal, gravel shield-to-rear bumper, anti-squeak. Also used as a door weatherstrip for some makes and models. Twelve (12) foot strip.
Pinchweld seal, windshield, to seal and retain outer reveal molding. Used with our #70-1192-52. Twelve (12) foot strip.
Insulators, rear coil spring. Fabric reinforced rubber as original. One (1) pair per car.
Weatherstrip, front bow to windshield, outer. Installs on convertible top. Approximately four (4) foot ten (10) inches long.
Rest pads, seat back, outer, on two (2) door styles with folding seats. Brown rubber. For black see our #70-0482-88. Self retaining, perfect copy.
Headlight Door To Lens Seal - Molded without wire. Double lip type for sealed beam headlights. Note: Compare with our single lip type #70-0389-14 sold separately.
Stainless beaded edge, mohair-lined, exact replacement for rear side of division bar. Available in 15" pairs.
Pad, fender parking light lens.Width: 5.125 inches. Height: 2.25 inches.
Pad, hood side center rest.
Weatherstrip, door window inner and outer, front and rear doors. Bend to fit. Available in a 3ft pair.
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Bumper, front suspension, upper arm.Height: 2.0 inches.
Rest pads, seat back, outer, on two (2) door styles with folding seats. Black rubber. For brown see our #70-0482-89. Self retaining, perfect copy.
This Windshield Division Bar Gasket is designed from the original part for superior fitment and seal. Part is properly sized with "H" section. Part requires fitting to top and bottom, as it is not drilled.
Headlight door to lens seal. Molded without wire. Single lip type for sealed beams.
Pad, brake and clutch pedal. Brown rubber. For black see our part #50-0054-22. Perfect copy, fine detail.Color:brown Width: 3.125 inches.
Hose, cowl vent gutter drain.Length: 7.0 inches.
This convertible top Front Bow Weatherstrip is designed from the original part for superior fitment and seal. This header seal installs directly to the windshield frame to seal between the soft top and the top of the windshield.
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For