Search Results
Rear Quarter Vent Window Weatherstrip
p/n: 40-0377-76
Weatherstrip, rear quarter vent window. Both sections, R & L, each made in one (1) strip to facilitate manufacturing. Must join two (2) ends together.
Front Door Vent Window Kit
p/n: 90-0355-90
This front door vent window weatherstrip kit is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Windshield Gasket
p/n: 40-0246-50
This windshield gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit.
Prop shaft support
p/n: 70-2857-27
Insulator, propeller shaft center bearing housing. Two (2) required per car.
Front Door Vent Window Weatherstrips
p/n: 40-0264-55
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Motor mount service
p/n: 40-0410-11
Front motor mount. Revulcanization service only. Send in core and allow three weeks for service. 6 cylinders only.
Trunk Weatherstrip
p/n: 70-1691-84
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Brown brake and clutch pad
p/n: 40-0121-89
Pads, brake and clutch pedal. Brown rubber. For black see our #40-0121-22. Oval style, perfect copy.
Fender welting 1/4" bead 50ft
p/n: 70-1098-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five
Fender welting 3/16 bead 50ft
p/n: 70-1100-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide, three sixteenths (3/16) inch, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty fi
Fender welting 50ft chrome
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Brown brake and clutch pad
p/n: 40-0107-89
Pads, brake and clutch pedal. Brown rubber. For black see our #40-0107-22. Full slip over type to fit old pedal.
Brake and clutch pedal pad
p/n: 40-0107-22
Pads, brake and clutch pedal. Black rubber. For brown see our #40-0107-89. Full slip over type to fit old pedal.
Swing-out Windshield Weatherstrip
p/n: 40-0018-52
This swing-out windshield weatherstrip comes in an eleven foot (11') strip and mounts into the metal channel attached to the glass. The rubber slides into the T-groove and creates a seal when the glass is pressed against the body of the vehicle.
Brake and clutch pedal pad
p/n: 40-0121-22
Pads, brake and clutch pedal. Black rubber. For brown see our #40-0121-89. Oval style, perfect copy.
Cowl vent gasket
p/n: 40-0271-54
Gasket, cowl vent. Fully molded to original cross-section and outline.Length: 18.0 inches.
Fuel neck grommet
p/n: 40-0043-39
Grommet, fuel filler neck. Fully molded rubber with retaining flange. Three and five eighths inch (3-5/8") outside diameter by two and one eighth inch (2-1/8") inside diameter by one inch (1") height.
Brake and clutch shank seal
p/n: 40-0217-24
Draft cap for brake and clutch pedal.Length: 2.4375 inches. Width: 1.6875 inches.
Fender welting 1/4" bead 25ft
p/n: 70-1097-44
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For
Fender welting 25ft chrome
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Fender welting 3/16 bead 25ft
p/n: 70-1099-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide, three sixteenths (3/16) inch, twenty five (25) foot roll. Typially used for attaching two (2) fenders to body. For f
Brake and clutch shank seal
p/n: 40-0175-24
Seal, brake and clutch pedal shank to floorboard. One and one half (1-1/2) inch by two and one eighth (2-1/8) inch by three fourths (3/4) inch thick.
Brake and clutch shank seal
p/n: 40-0016-24
Seal, brake and clutch pedal shank to floorboard (draft excluder).Length: 2.4375 inches. Width: 1.875 inches.
Firewall grommet
p/n: 40-0222-21
Grommet, firewall, for throttle cable, wiper vacuum line and cowl vent drain hole. Three (3) holes (9/16", 3/8", 1/4").
Beltline Weatherstrip
Window felt inner and/or outer. Flexible, pile lined, rubber covered, with black bead. Available in 2ft and 3ft pairs.
Firewall grommet
p/n: 40-0221-21
Grommet, firewall, for speedometer cable, oil tube, temp. tube, 3 holes (5/16", 1/4", 3/16").
Windshield Division Bar Gasket
p/n: 70-0098-52
Gasket, divided windshield center post. Combines inner and outer gasket in one piece as original. For seventeen (17) inch to (20) inch lengths. Gasket length: 20 inches, trim to fit.
Vent division bar weatherstrip
p/n: 70-1432-56
Vent window division post seal. Single approximate 32 inch strip of original cross section extruded rubber that must be cut in half to complete a pair for both the driver and passenger side door vents. To install this part, one typically uses an ad
Steering column cushion
p/n: 40-0259-36
Pad, steering post bracket. One (1) per car. Cushions steering post clamp to instrument panel.Length: 3.50 inches.
Battery clamp cover
p/n: 70-0095-21
Cover, battery clamp. Control unsightly sulfate buildup. Help protect the nearby metal and finish. Good copy from original part.Length: 3.5 inches.
Hood support rod top cap
p/n: 40-0346-42
Pad, hood rest rod. For five sixteenths (5/16) inch diameter hood support rod. Also see our #40-0103-42.Length: 1.0 inches.
Body mounting pad
p/n: 40-0232-48
Pad, body mounting, upper. Fully molded rubber with locating collar. As many as twelve (12) used per car. One and fifteen sixteenths inch (1 15/16") outside width by two inch (2") outside width. See drawing for more dimensions.
Steering gear bushing
p/n: 40-0130-36
Bushing, insulator, for steering gear arm. Four (4) required per car.
Body mounting pad
p/n: 40-0233-48
Pad, body mounting, lower. Fully molded rubber. One and thirteen sixteenths inch (1 13/16") outside width by one and fifteen sixteenths inch (1 15/16") outside length by one half inch (1/2") inside hole diameter by three eighths inch (3/8") height.
Body mounting pad
p/n: 40-0231-48
Pad, body mounting, upper. Fully molded rubber with locating collar. One and fifteen sixteenths inch (1 15/16") outside diameter by three fourths inch (3/4") locating collar outside diameter by one half inch (1/2") inside locating hole diameter. Three eig
Body mounting pad
p/n: 40-0230-48
Pad, body mounting, lower. Fully molded rubber. One and eleven sixteenths inch (1 11/16") outside diameter by nine sixteenths inch (9/16") inside hole diameter by one half inch (1/2") height.
Masticated rubber sheet
p/n: 70-0645-45
Masticated sheet. Three thirty seconds (3/32) inch thick rubber sheet containing random milled cotton cord reinforcement for front end splash aprons, etc. This product is a four (4) foot wide roll, and will only be sold in four (4) square foot multiples
Dense Rubber Extrusion
p/n: 40-0054-99
Windshield, rear window and rear fixed quarter window weatherstrip. Available by the foot.
Spring shackle bushing
p/n: 40-0183-32
Bushing, spring and shackle, front and rear leaf springs. Eight (8) or twelve (12) required per car.Length: 1.25 inches. Height: 1.25 inches.
Trunk Weatherstrip (Sponge Rubber Extrusion - General Use)
p/n: 30-0356-85
Trunk weatherstrip made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
Dense Rubber Extrusion
p/n: 40-0053-99
Windshield, rear window and rear fixed quarter window weatherstrip. Available by the foot.
Peel-N-Stick Trunk Weatherstrip
p/n: 30-0356-WT
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.