Motor mount (insulator assembly, support, rear), right and left. Revulcanization service only.
This Windshield Gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit.
This four (4) piece Front Door Vent Window Weatherstrips contain the upper and lower seals that cover the top, front, and bottom of the vent window. All of the pieces are designed from original parts for a precise, factory fit.
Bumper, front suspension (inside of coil spring). Made with three eighths (3/8) inch stud as original.
Bushing, rear spring and shackle. One and one eighth (1-1/8) inch diameter with nine sixteenths (9/16) inch hole. One set contains twelve (12) pieces.
Weatherstrip, side window. Fits metal channel. Rubber only. Twelve (12) foot strip.Length: 144.0 inches. Width: .75 inches.
Bushings, front suspension torque arm. Necessary for proper front end geometry.
Bumpers, rear axle spring.Length: 5.375 inches. Width: 2.75 inches. Height: 2.1875 inches.
Insulator assembly, transmission support. Revulcanization service only. Send in your old core for service.
Stabilizer assembly. Revulcanization service only.
Grommet, steering column to instrument panel. Brown rubber only, excellent copy.Length: 5.0 inches. Width: 3.0 inches.
Gaskets, front parking light to fender.Length: 19.875 inches.
Pedal, accelerator. Revulcanization service only. Includes new rod ball socket and pivot. Original pattern tread.Length: 9.625 inches. Width: 1.9375 inches.
This Front Spring Bumper pair is a quality reproduction of the original factory part. Self retaining type bumper manufactured with top quality materials.
Boots, shifter relay shaft end support.
Grommets, front bumper. Proper hollow construction as original for good fit. Fully molded rubber. Five and one eighths inch (5-1/8") outside length by two and three eighths inch (2-3/8") outside width by one and five eighths inch (1-5/8") inside hole leng
Grommet, steering column at toe board.Length: 4.375 inches.
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching four (4) fenders to body. Sold in a 50 foot roll.
Insulators, front engine support at timing gear cover.
Gaskets, headlight rim (headlight door).
Gravel deflector, underside of running board at rear. Length: 7.125 inches.
Pads, brake and clutch pedal, slip over type. Black and red rubber. For black only see our #30-0188-22.Length: 3.875 inches. Width: 2.875 inches.
Mounting pad, taillight. With proper edging and shape, molded left and right. Sold only in complete pairs.Length: 9.75 inches.
Scuff pad, hood to cowl. Superior duplication of part with better rubber than original.Length: 8.25 inches.
Retainer, intermediate bearing. All models with two piece driveshafts.
Pads, brake and clutch pedal, slip over type. Black rubber only. For black and red (semi-automatic clutch models) see our #30-0188-89.Length: 3.875 inches.
Gasket, headlight front assembly to fender. Between headlight bucket and the fender receiver hole. One (1) pair per car, sold only in pairs.
Pad, fenderskirt edge, similar to our #70-0055-45, but thinner. Approximately five (5) foot strip per skirt.Length: 60.0 inches. Width: .15625 inches.
Bushing, insulator, front suspension lower support arm, inner. Four (4) piece set.
Bushing, insulator, torque arm to frame at rear. Four (4) piece set.
Bearings or bushings, front stabilizer rod. One (1) pair used per vehicle. Fully molded rubber. One and nine sixteenths inch (1 9/16") length by one and nine sixteenths inch (1 9/16") width by three fourths inch (3/4") inside hole diameter by one and elev
Bumper assembly, front door hinge, upper, stop. Two (2) per car, steel core as original.Height: .6875 inches.
Bushing, insulator, upper support arm, outer above steering knuckle support. Four (4) piece set.
Bushings, front stabilizer mounting bracket. Fully molded rubber. One and seven sixteenths inch (1 7/16") length by one and five eighths inch (1 5/8") width by five eighths inch (5/8") inside hole diameter by one and eleven sixteenths inch (1 11/16") heig
Gasket, cowl vent. Perfect reproduction, high quality, original configuration, not a sponge substitute.Length: 14.0 inches. Width: 5.75 inches.
Boot, hydraulic window lifting cylinder, front and rear.
Insulator, engine snubber. One four (4) piece set required per car. Sold only in complete sets.
Boot, clutch control unit governor.1940-42: Cars with Overdrive 1941-42: Cars with ElectromaticHeight: 1.125 inches.
Front vent window division post seal. Fully molded with metal core and attaching tabs.
This Beltline Weatherstrip is sold as a three (3) foot pair. The beltline is used for side window inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Boot, brake and clutch pedal shank at toe board.Length: 2.9375 inches.
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching two (2) fenders to body. Sold in a 25 foot roll.
Boot, valve, direct acting solenoid. Height: .75 inches.
Bushing, steering gear lever ball stud (Pitman arm). Originally made in one piece as spool bushing, but replacements made in halves.
Mount, radio antenna wire, under running board. Found on several models with factory type antennas that mount under the running board.
Bowdrill cloth tape is used for covering convertible side window weatherstrip. Available in a 5 ft roll.