Search Results
Motor mount service
p/n: 30-0325-11
Motor mount (insulator assembly, support, rear), right and left. Revulcanization service only.
Rear Window Gasket
p/n: 30-0358-81
This rear window gasket mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit.
Front suspension bumper
p/n: 30-0489-32
Bumper, front suspension (inside of coil spring). Made with three eighths (3/8) inch stud as original.
Spring eye bushing
p/n: 30-0372-32
Bushing, rear spring eye leaf and shackle. Nine sixteenths (9/16) inch inside diameter, one and three eighths (1-3/8) inch barrel.
Front suspension bushing
p/n: 30-0239-32
Bushings, front suspension torque arm. Necessary for proper front end geometry.
Axle rebound pad
p/n: 30-0125-32
Bumpers, rear axle spring.Length: 5.375 inches. Width: 2.75 inches. Height: 2.1875 inches.
Transmission mount service
p/n: 30-0316-24
Insulator assembly, transmission support. Revulcanization service only. Send in your old core for service.
Steering column grommet
p/n: 30-0048-36
Grommet, steering column to instrument panel. Brown rubber only, excellent copy.Length: 5.0 inches. Width: 3.0 inches.
Trunk Weatherstrip
p/n: 70-0083-85
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Parking light mounting pad
p/n: 30-0195-17
Gaskets, front parking light to fender.Length: 19.875 inches.
Accelerator pedal service
p/n: 30-0401-41
Pedal, accelerator. Revulcanization service only. Includes new rod ball socket and pivot. Original pattern tread.Length: 9.625 inches. Width: 1.9375 inches.
Front bumper grommet
p/n: 30-0071-28
Grommets, front bumper. Proper hollow construction as original for good fit. Fully molded rubber. Five and one eighths inch (5-1/8") outside length by two and three eighths inch (2-3/8") outside width by one and five eighths inch (1-5/8") inside hole leng
Fender welting 1/4" bead 50ft
p/n: 70-1098-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five
Fender welting 3/16 bead 50ft
p/n: 70-1100-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide, three sixteenths (3/16) inch, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty fi
Fender welting 50ft chrome
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Gravel Shield
p/n: 30-0007-44
Gravel deflector, underside of running board at rear. Length: 7.125 inches.
Red brake and clutch pedal pad
p/n: 30-0188-89
Pads, brake and clutch pedal, slip over type. Black and red rubber. For black only see our #30-0188-22.Length: 3.875 inches. Width: 2.875 inches.
Hood to cowl weatherstrip
p/n: 30-0049-42
Scuff pad, hood to cowl. Superior duplication of part with better rubber than original.Length: 8.25 inches.
Prop shaft retainer bushing
p/n: 70-2268-27
Retainer, intermediate bearing. All models with two piece driveshafts.
Brake and clutch pedal pad
p/n: 30-0188-22
Pads, brake and clutch pedal, slip over type. Black rubber only. For black and red (semi-automatic clutch models) see our #30-0188-89.Length: 3.875 inches.
Headlight mounting pad
p/n: 30-0354-14
Gasket, headlight front assembly to fender. Between headlight bucket and the fender receiver hole. One (1) pair per car, sold only in pairs.
Fenderskirt edge seal
p/n: 20-0111-44
Pad, fenderskirt edge, similar to our #70-0055-45, but thinner. Approximately five (5) foot strip per skirt.Length: 60.0 inches. Width: .15625 inches.
Suspension bushing
p/n: 30-0339-36
Bushing, insulator, front suspension lower support arm, inner. Four (4) piece set.
Front stabilizer bushing
p/n: 30-0363-33
Bearings or bushings, front stabilizer rod. One (1) pair used per vehicle. Fully molded rubber. One and nine sixteenths inch (1 9/16") length by one and nine sixteenths inch (1 9/16") width by three fourths inch (3/4") inside hole diameter by one and elev
Door Bumper
p/n: 34-0305-71
Bumper assembly, front door hinge, upper, stop. Two (2) per car, steel core as original.Height: .6875 inches.
Suspension bushing
p/n: 30-0341-36
Bushing, insulator, upper support arm, outer above steering knuckle support. Four (4) piece set.
Cowl vent gasket
p/n: 30-0050-54
Gasket, cowl vent. Perfect reproduction, high quality, original configuration, not a sponge substitute.Length: 14.0 inches. Width: 5.75 inches.
Flexible Run Channel
p/n: 70-1108-57
Channel, flexible window run, un-beaded. Cloth covered mohair-lined type. Available in 6ft lengths.
Motor snubber pad
p/n: 30-0311-11
Insulator, engine snubber. One four (4) piece set required per car. Sold only in complete sets.
Clutch control boot
p/n: 30-0273-24
Boot, clutch control unit governor.1940-42: Cars with Overdrive 1941-42: Cars with ElectromaticHeight: 1.125 inches.
Flexible Run Channel
p/n: 70-1239-58
Cloth covered, mohair lined flexible metal channel for sides and top of door windows.
Vent division bar weatherstrip
p/n: 30-0530-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Beltline Weatherstrip
p/n: 70-0555-58
Weatherstrip, door window inner and outer, front and rear doors. Bend to fit. Available in a 3ft pair.
Brake and clutch shank seal
p/n: 30-0143-24
Boot, brake and clutch pedal shank at toe board.Length: 2.9375 inches.
Flexible Run Channel
p/n: 70-1238-58
Cloth covered, mohair lined flexible metal channel for sides and top of door windows.
Fender welting 1/4" bead 25ft
p/n: 70-1097-44
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For
Fender welting 25ft chrome
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Fender welting 3/16 bead 25ft
p/n: 70-1099-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide, three sixteenths (3/16) inch, twenty five (25) foot roll. Typially used for attaching two (2) fenders to body. For f
Flexible Run Channel
p/n: 70-1107-57
Cloth covered mohair-lined type. For sides and top of side windows. Available in 5ft lengths.
Steering gear bushing
p/n: 30-0340-36
Bushing, steering gear lever ball stud (Pitman arm). Originally made in one piece as spool bushing, but replacements made in halves.
Antenna Wire Mount
p/n: 70-2263-19
Mount, radio antenna wire, under running board. Found on several models with factory type antennas that mount under the running board.
Brown gearshift boot
p/n: 30-0069-89
Boot, gearshift on steering column. Brown rubber. For black see our #30-0069-36. Two and one eighth (2-1/8) inch long style.