Search Results
Door opening step pad
p/n: 70-1118-45
Mats, front door opening, with metal backing, proper body contour and attaching holes. Two (2) piece set for both front doors.Length: 30.375 inches.
Door opening step pad
p/n: 70-1119-45
Mats, rear door opening, with metal backing, proper body contour and attaching holes. Two (2) piece set for both rear doors.Length: 21.875 inches.
Front Door Weatherstrip Kit
p/n: 90-0108-72
Front door weatherstrip kit. This four (4) piece kit is the primary seal for the door to the body. Set includes the door edge weatherstrip with molded corners and hinge post weatherstrip.
Side Window Run Channel Kit
p/n: 90-0141-58
This ten (10) piece kit includes the inner and outer windowfelts, upper and lower rigid run channels, and flexible run channels needed to complete two (2) doors.
Front Door Vent Window Kit
p/n: 90-0380-90
This front door vent window weatherstrip kit is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Side Window Run Channel Kit
p/n: 90-0142-58
This six (6) piece kit includes the inner and outer windowfelts and flexible run channels needed to complete two (2) doors. Used for front or rear doors in models without vent windows in the door.
Rear Door weatherstrip
p/n: 90-0132-72
Rear door edge weatherstrip. This part is the primary door to body weatherstrip. Includes the perimeter seal for both rear doors and the molded corners. Set consists of four (4) pieces. Kit does not include adhesive. Includes the following components
Motor mount service
p/n: 60-0224-11
Engine mount, side (support cushions), right and left. Side frame bracket to clutch housing bracket. Two (2) per car.Width: 2.5 inches. Height: 1.5 inches.
Front Door Vent Window Weatherstrips
p/n: 38-0037-55
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Motor mount service
p/n: 60-0296-11
Cushion, engine mount, front. Revulcanization service only.Length: 3.0 inches. Width: 2.125 inches.
Gravel shield
p/n: 60-0575-45
Gravel shield, rear fender. Right and left hand carefully tooled stone shields crafted to factory design.
Windshield Gasket
p/n: 60-0187-50
This windshield gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit.
Rear Window Gasket
p/n: 60-0280-81
This rear window gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Spring seat service
p/n: 60-0619-35
Seat, rear spring. Revulcanization service only. Send in complete casting with metal sleeve bushing.
Rear spring bumper service
p/n: 60-0425-32
Bumpers, rear springs to frame. Revulcanization service only.Length: 3.0 inches. Width: 2.5 inches.
Windshield Gasket
p/n: 70-1534-50
A vulcanized windshield weatherstrip for windows without chrome reveal molding or divider bar. This windshield weatherstrip mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Transmission mount service
p/n: 60-0530-25
Insulator, plate assembly, guide, transmission support bracket. Revulcanization service only.Used with our #60-0315-25 from 1940 to 1946..Length: 5.
Trunk Weatherstrip
p/n: 70-0988-84
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Transmission mount service
p/n: 60-0407-25
Insulator (support), transmission mounting. Revulcanization service only.Length: 7.0625 inches.
Fender welting 1/4" bead 50ft
p/n: 70-1098-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five
Fender welting 3/16 bead 50ft
p/n: 70-1100-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide, three sixteenths (3/16) inch, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty fi
Fender welting 50ft chrome
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Front Stabilizer Kit
p/n: 60-0221-33
Link kit, full replacement, front stabilizer bar link. Twenty two (22) piece set. Hex head bolt 5/16"-24NF x 6-3/8" long. Comes with metal sleeve, metal cup washers and rubber grommets.
Fenderskirt Edge Seal
p/n: 70-0154-45
Seal, fenderskirt edge, exact copy, trim notch for skirt lock at installation. Compare sketch with your original to be sure. Two (2), five (5) foot strips.
Fenderskirt edge seal
p/n: 70-0289-45
Seal, fenderskirt edge. Good quality and workmanship, see sketch for comparison. Ten (10) foot strip.Length: 120.0 inches. Width: .1875 inches.
Hood to cowl weatherstrip
p/n: 60-0091-42
Seal, side of hood ledge (cowl). Molded with all original details. One (1) pair required per car.Length: 11.0 inches.
Fenderskirt edge seal
p/n: 20-0111-44
Pad, fenderskirt edge, similar to our #70-0055-45, but thinner. Approximately five (5) foot strip per skirt.Length: 60.0 inches. Width: .15625 inches.
Front Suspension Rubber Bumper
p/n: 60-0103-32
Front Suspension Rubber Bumper for the front suspension lower control arm (attaches to lower arm spring mount). Steel core, with original size bolt. Width: 1.625 inches.
Taillight mounting pad
p/n: 60-0008-15
Mounting pads, taillight.Length: 6.50 inches. Width: 2.6875 inches.
Brake and Clutch Pedal Pads
p/n: 60-0068-22
Brake and Clutch Pedal Pads - The proper design and fully detailed with ribs extending down over sides of the pad. Length: 3.50 inches. Width: 2.0 inches.
Front Spring Rubber Bumper
p/n: 70-0329-32
Front Spring Rubber Bumper - for upper control arm on frame.
Front fender seal
p/n: 60-0522-45
Seal, front fender baffle, right and left. One (1) pair per car. Length: 5.25 inches.
Gravel shield anti-squeak
p/n: 60-0020-30
Anti-squeak, rear gravel deflector-to-bumper. Excellent copy of original extrusion. Six (6) foot strip.Width: 1.0 inches.
Window pinchweld seal
p/n: 70-0096-52
Pinchweld seal, windshield, to seal and retain outer reveal molding. Used with our #70-1192-52. Twelve (12) foot strip.
Accelerator pedal service
p/n: 60-0701-40
Pedal, accelerator. Revulcanization service only. Excellent cover detailing with molded in rod ball socket as original.
Brown steering column grommet
p/n: 60-0621-89
Grommet, steering column to toe board. Brown rubber. For black see our #60-0621-36.Color:brown Length: 4.25 inches.
Headlight Door To Lens Seal
p/n: 70-0493-14
Headlight Door To Lens Seal - Molded without wire. Double lip type for sealed beam headlights. Note: Compare with our single lip type #70-0389-14 sold separately.
Rigid Run Channel
p/n: 70-0347-58
Stainless beaded edge, mohair-lined, exact replacement for rear side of division bar. Available in 15" pairs.
Steering column grommet
p/n: 60-0621-36
Grommet, steering column to toe board. Black rubber. For brown see our #60-0621-89.
Flexible Run Channel
p/n: 70-1239-58
Cloth covered, mohair lined flexible metal channel for sides and top of door windows.
Beltline Weatherstrip
p/n: 70-0555-58
Weatherstrip, door window inner and outer, front and rear doors. Bend to fit. Available in a 3ft pair.
Inner Fender Seal
p/n: 60-0288-45
Inner Fender Seal for anti-rattle, runningboard apron to body, or fender splash panels. Nine sixteenths (9/16) inch by seven eighths (7/8) inch slotted sponge rubber to accept rivets. Sold in eight (8) foot strips.
Headlight Door To Lens Seal
p/n: 70-0389-14
Headlight door to lens seal. Molded without wire. Single lip type for sealed beams.
Vent division bar weatherstrip
p/n: 60-0569-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Windshield Division Bar Gasket
p/n: 70-0372-51
Gasket, windshield center post, "H" section, properly sized, requires fitting to top and bottom, not drilled.
Rear spring bushing
p/n: 60-0311-35
Bushing, rear spring front eye, inlox cartridge type as original.
Flexible Run Channel
p/n: 70-1238-58
Cloth covered, mohair lined flexible metal channel for sides and top of door windows.
Fender welting 1/4" bead 25ft
p/n: 70-1097-44
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For