Weatherstrip, front door kit. Includes sufficient weatherstrip for door perimeter and hinge pillar. Eight (8) piece kit.
Weatherstrip, rear door kit. Includes sufficient weatherstrip for door perimeter, bottom and hinge pillar. Adhesive is not included in the kit.
This front door vent window weatherstrip set is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Rear door vent window rubber. Order our #30-0347-74 division post seal separately.
Weatherstrip, front door to fender (hinge pillar). Soft, solid rubber construction with tabs for all screws, but without metal core.
Weatherstrip, rear door hinge on center pillar.Length: 32.0 inches.
This Windshield Gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit.
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
This rear window gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Diaphragm, electromatic clutch control vacuum cylinder. Restores proper operation to clutch if diaphragm leaks air.
Grommet, steering column to dash at floorboard. Fully molded with metal core out of durable black rubber.
Bumpers, rear axle spring.Length: 5.375 inches. Width: 2.75 inches. Height: 2.1875 inches.
Pads, taillight mounting. For styles without ribbed door lights. Molded left and right.
Bumper, front spring rebound, lower.Width: 2.125 inches. Height: 2.25 inches.
Pedal, accelerator. Revulcanization service only. Includes new rod ball socket and pivot. Original pattern tread.Length: 9.625 inches. Width: 1.9375 inches.
Grommets, rear bumper extension bar through rear fender for wrap around bumpers. Fully molded rubber w/ full detail as in original. Four and one half inch (4-1/4") outside diameter by one and five eighths inch (1-5/8") inside hole length by one fourth inc
Grommet, rear door vent divider post. Upper and lower, right and left. 4 piece set.
Grommet, radiator cradle to frame tie rod. 1st type, with locating boss. One four (4) piece set required per car. See also our #30-0309-31.
Cushions, motor support, at timing gear cover. One (1) pair required per car. Sold only in pairs.
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Cushion, rear gravel to bumper. Six (6) feet long. One (1) strip required per car.Length: 72.00 inches. Width: .25 inches. Height: .6875 inches.
Bumper, front spring rebound, upper.Height: 2.25 inches.
Pads, brake and clutch pedal, slip over type. Black and red rubber. For black only see our #30-0188-22.Length: 3.875 inches. Width: 2.875 inches.
Channel, rigid run, for division bar, un-beaded, plush lined, cloth covered, twenty four (24) inches long, channel size one half (1/2) inch outside width
Retainer, intermediate bearing. All models with two piece driveshafts.
Pads, brake and clutch pedal, slip over type. Black rubber only. For black and red (semi-automatic clutch models) see our #30-0188-89.Length: 3.875 inches.
Grommets, hood lock link through firewall.
Grommet, several useages. Radiator core cradle tie rod to frame or rear stablizer pad to link to where the leaf springs are bolted. Fully molded rubber. 2nd type with chamfered edge. Comes as a (4) piece set. One and three eighths inch (1 3/8") outside di
Bushings, front stabilizer mounting bracket. Fully molded rubber. One and seven sixteenths inch (1 7/16") length by one and five eighths inch (1 5/8") width by five eighths inch (5/8") inside hole diameter by one and eleven sixteenths inch (1 11/16") heig
Grommet, ignition cable.Length: 2.125 inches. Width: 1.50 inches.
Channel, flexible window run, un-beaded. Cloth covered mohair-lined type. Available in 6ft lengths.
Insulator, engine snubber. One four (4) piece set required per car. Sold only in complete sets.
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Weatherstrip, rear vent window, front edge (on division post) right and left.
Cloth covered, mohair lined flexible metal channel for sides and top of door windows.
This Beltline Weatherstrip is sold as a three (3) foot pair. The beltline is used for side window inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt 3/8"-16 NF x 6-15/16" long. Comes with metal sleeve, metal cup washers and rubber grommets.
Boot, brake and clutch pedal shank at toe board.Length: 2.9375 inches.
Grommet, shifter shaft to shroud. One (1) per car.Length: 4.125 inches. Width: 2.3125 inches.
Pad, rear license light mounting, with correct dimensions and beading.Length: 8.125 inches.
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
This Side Window Weatherstrips can be used for inner and/or outer. The weatherstrip is flexible, pile lined, rubber covered, with black bead. Available in 3ft pairs.
Gaskets, headlight body mounting to fender. Cut to exact size as original.
Gasket, rear trunk lock and handle mounting.Length: 4.0 inches.
Cloth covered mohair-lined type. For sides and top of side windows. Available in 5ft lengths.
Pad, roof mounted antenna gasket. Models with antenna mounted above center of windshield.
Boot, gearshift on steering column. Brown rubber. For black see our #30-0069-36. Two and one eighth (2-1/8) inch long style.
Hood Rest Pad. Molded rubber with a steel core. Six (6) required per car. Length: 1.75 inches Width: 1.625 inches.
Grommet, speedometer cable through firewall. Retained by steel collar (not included). Two and one half (2-1/2) inch outside diameter.
Grommet, firewall, vacuum antenna line through firewall. Four holes provided but three left masked for use if needed.