Search Results
Side Window Run Channel Kit
p/n: 90-0141-58
This ten (10) piece kit includes the inner and outer windowfelts, upper and lower rigid run channels, and flexible run channels needed to complete two (2) doors.
Front Door Weatherstrip Kit
p/n: 90-0111-72
Front door weatherstrip kit. This eight (8) piece kit is the primary seal for the door to the body. Set includes the door bottom with molded corners, hinge pillar bellows, front edge seals, and door edge weatherstrip.
Front Door Vent Window Set
p/n: 90-0401-90
This front door vent window weatherstrip set is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Rear Door weatherstrip
p/n: 70-1444-72
Door edge weatherstrip. This part is the primary door to body weatherstrip. Adhesive not included in kits.
Windshield Gasket
p/n: 60-0151-50
This windshield gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
Rear door vent weatherstrip
p/n: 38-0086-74
Vent window weatherstrip, rear door. Note: we do not have a matching metal core division post seal for this part. Please order our part #70-0040-56 separately.
Front Door Vent Window Weatherstrips
p/n: 38-0059-55
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Trunk Weatherstrip
p/n: 70-0870-84
This trunk weatherstrip set is designed from original parts for superior fitment and seal. The set contains the strips and corners that mount to the body and the strip that mounts to the lid.
Door weatherstrip
p/n: 60-0250-73
Weatherstrip, door bottom and corners, molded right and left. Overall length forty and three fourths (40-3/4) inch per door.
Rear Window Gasket
p/n: 60-0152-81
This rear window gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation. It also has the slot to accommodate the outer edge's decorative molding.
Spring seat service
p/n: 60-0619-35
Seat, rear spring. Revulcanization service only. Send in complete casting with metal sleeve bushing.
Rear spring bumper service
p/n: 60-0425-32
Bumpers, rear springs to frame. Revulcanization service only.Length: 3.0 inches. Width: 2.5 inches.
Motor Mount
p/n: 60-0225-11
Side motor mounts. Revulcanization service only. Two (2) required per car.
Door weatherstrip
p/n: 60-0476-73
Weatherstrip, auxiliary, front door opening. Right and left, at beltline on body hinge post, above upper hinge. Metal core, as original, with screw holes.
Fender welting 1/4" bead 50ft
p/n: 70-1098-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five
Fender welting 3/16 bead 50ft
p/n: 70-1100-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide, three sixteenths (3/16) inch, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty fi
Fender welting 50ft chrome
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Door weatherstrip
p/n: 60-0517-73
Weatherstrip, front door hinge pillar at beltline. Fourteen and one half (14-1/2) inches long, molded right and left.Length: 13.75 inches.
Trunk Weatherstrip Corners
p/n: 60-0511-85
These trunk weatherstrip corners are designed from the original part for superior fitment and seal. The seals mount to the front corners of the trunk directly to the body.
Front Stabilizer Kit
p/n: 60-0221-33
Link kit, full replacement, front stabilizer bar link. Twenty two (22) piece set. Hex head bolt 5/16"-24NF x 6-3/8" long. Comes with metal sleeve, metal cup washers and rubber grommets.
Taillight mounting pad
p/n: 60-0176-15
Pad, taillight body mounting. Three (3) inch by six and one half (6-1/2) inch overall. Proper lip design.Length: 6.50 inches. Width: 3.0 inches.
Steering column floorplate
p/n: 60-0395-36
Cover (grommet), steering gear-to-toe board seal.Width: 5.8125 inches. Height: 6.0 inches.
Fenderskirt edge seal
p/n: 20-0111-44
Pad, fenderskirt edge, similar to our #70-0055-45, but thinner. Approximately five (5) foot strip per skirt.Length: 60.0 inches. Width: .15625 inches.
Division Bar Grommet
p/n: 70-0483-62
Grommets, rear door vent divider post (wind deflector), upper and lower, right and left. Four (4) piece set.
Exhaust system support pad
p/n: 60-0319-13
Insulator (support), exhaust system, right angle type, fabric reinforced. Steel core at one end as original.Width: 2.5 inches. Height: 1.625 inches.
Brake and Clutch Pedal Pads
p/n: 60-0068-22
Brake and Clutch Pedal Pads - The proper design and fully detailed with ribs extending down over sides of the pad. Length: 3.50 inches. Width: 2.0 inches.
Front Spring Rubber Bumper
p/n: 70-0329-32
Front Spring Rubber Bumper - for upper control arm on frame.
Hood to cowl weatherstrip
p/n: 60-0428-42
Anti-squeak, hood to cowl ledge. Two (2) pieces with holes, ready to install.Length: 21.0 inches. Width: .625 inches.
License light mounting pad
p/n: 60-0174-17
Pad. rear license light mounting. Two and three fourths (2-3/4) inch by three and nine thirty seconds (3-9/32) inch overall. Two (2) required per vehicle.
Headlight Door To Lens Seal
p/n: 70-0493-14
Headlight Door To Lens Seal - Molded without wire. Double lip type for sealed beam headlights. Note: Compare with our single lip type #70-0389-14 sold separately.
Rigid Run Channel
p/n: 70-0347-58
Stainless beaded edge, mohair-lined, exact replacement for rear side of division bar. Available in 15" pairs.
Flexible Run Channel
p/n: 70-1239-58
Cloth covered, mohair lined flexible metal channel for sides and top of door windows.
Beltline Weatherstrip
p/n: 70-0555-58
Weatherstrip, door window inner and outer, front and rear doors. Bend to fit. Available in a 3ft pair.
Vent division bar weatherstrip
p/n: 60-0494-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Inner Fender Seal
p/n: 60-0288-45
Inner Fender Seal for anti-rattle, running board apron to body, or fender splash panels. Nine sixteenths (9/16) inch by seven eighths (7/8) inch slotted sponge rubber to accept rivets. Sold in eight (8) foot strips.
Bumper support bar pad
p/n: 60-0420-30
Pads, rear bumper bar, inner, to quarter panel. Fully molded rubber. Two and eleven sixteenths inch (2-11/16") outside length by one inch (1") outside width by one and five eighths inch (1-5/8") inside hole length by one fourth inch (1/4") inside hole wid
Rear spring bushing
p/n: 60-0311-35
Bushing, rear spring front eye, inlox cartridge type as original.
Flexible Run Channel
p/n: 70-1238-58
Cloth covered, mohair lined flexible metal channel for sides and top of door windows.
Fender welting 1/4" bead 25ft
p/n: 70-1097-44
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For
Fender welting 25ft chrome
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Sliding Quarter Window Weatherstrip
p/n: 70-0353-78
Weatherstrip, door window inner and outer, front and rear doors. Bend to fit. Available in a 6ft lengths.
Fenderskirt Edge Seal
p/n: 60-0109-45
Fenderskirt Edge Seal - One (1) ten (10) foot strip. Length: 120.0 inches.
Front suspension bumper
p/n: 50-0092-32
Bumper, front suspension, lower arm. Steel core, with threaded stud, as original. Two (2) per car required.
Fender welting 3/16 bead 25ft
p/n: 70-1099-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide, three sixteenths (3/16) inch, twenty five (25) foot roll. Typially used for attaching two (2) fenders to body. For f
Front Stabilizer Bushing
p/n: 60-0088-34
Front Stabilizer Bushing - Front stabilizer bar mounting. Fully molded rubber. Two (2) required per car. One and five sixteenths inch (1 5/16") length by one and five sixteenths inch (1 5/16") width by five eighths inch (5/8") inside hole diameter by one and three fourths inch (1 3/4") height.
Gravel shield anti-squeak
p/n: 60-0173-30
Seal, rear bumper face bar-to-body (gravel shield). Fully molded rubber with all original features. Seventy-nine inches (79") long. Extrusion ends measure one and three fourths inch (1-3/4") wide by nine sixteenths inch (9/16") height.
Side Window Sash Channel
p/n: 70-0641-58
Sash channel, side window glass. U-shaped steel channel only, no filler. Will require that you attach your own window regulator cam to underside as required.