Search Results
Rear Window Gasket
p/n: 60-0121-81
This rear window gasket mounts around the full perimeter of the back glass and has the divider bars molded directly into it. It has properly molded corners to precisely conform to the glass and has the slot to accommodate the outer edge's decorative molding.
Hardtop roof rail weatherstrip
p/n: 60-0274-68
Hardtop roof rail weatherstrip (1950-2nd type). Goes over the front doors only. This part fits on the roof of the vehicle and seals the side window when the window is fully raised. Replaces 4600737-8. Note: compare with part #60-0272-68 for
Door Weatherstrip Kit
p/n: 90-0113-72
Door weatherstrip kit. This kit is the primary seal for the door to the body. Set includes the door bottom with molded corners, hinge pillar bellows, front edge seals, and rear edge seals.
Front Door Vent Window Set
p/n: 90-0382-90
This front door vent window weatherstrip kit is a six (6) piece set that contains the main vent window seals, base extensions, and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Windshield Gasket
p/n: 60-0194-50
This windshield gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
Front Door Vent Window Weatherstrips
p/n: 38-0038-55
This front door vent window weatherstrip set contains the main seals for the vent windows and the base extension pieces for the frame. They are designed and molded from original parts for superior fitment and seal.
Windshield Gasket
p/n: 70-1791-50
This windshield gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Motor mount service
p/n: 60-0296-11
Cushion, engine mount, front. Revulcanization service only.Length: 3.0 inches. Width: 2.125 inches.
Trunk Weatherstrip
p/n: 70-0870-84
This trunk weatherstrip set is designed from original parts for superior fitment and seal. The set contains the strips and corners that mount to the body and the strip that mounts to the lid.
Door weatherstrip
p/n: 60-0250-73
Weatherstrip, door bottom and corners, molded right and left. Overall length forty and three fourths (40-3/4) inch per door.
Transmission mount service
p/n: 60-0312-25
Insulator (support), motor at transmission. One (1) per car. Revulcanization service only.Length: 7.75 inches.
Spring seat service
p/n: 60-0619-35
Seat, rear spring. Revulcanization service only. Send in complete casting with metal sleeve bushing.
Rear spring bumper service
p/n: 60-0425-32
Bumpers, rear springs to frame. Revulcanization service only.Length: 3.0 inches. Width: 2.5 inches.
Motor Mount
p/n: 60-0225-11
Side motor mounts. Revulcanization service only. Two (2) required per car.
Door weatherstrip
p/n: 60-0324-73
Weatherstrip, front door opening. Right and left, hinge pillar at beltline. Constructed of soft rubber.Length: 12.0 inches.
Trunk Weatherstrip Corners
p/n: 60-0511-85
These trunk weatherstrip corners are designed from the original part for superior fitment and seal. The seals mount to the front corners of the trunk directly to the body.
Front Stabilizer Kit
p/n: 60-0221-33
Link kit, full replacement, front stabilizer bar link. Twenty two (22) piece set. Hex head bolt 5/16"-24NF x 6-3/8" long. Comes with metal sleeve, metal cup washers and rubber grommets.
Steering column floorplate
p/n: 60-0395-36
Cover (grommet), steering gear-to-toe board seal.Width: 5.8125 inches. Height: 6.0 inches.
Door bumper
p/n: 70-0168-71
Bumper, door side. Square type held by four (4) screws, metal core as original.
Exhaust system support pad
p/n: 60-0319-13
Insulator (support), exhaust system, right angle type, fabric reinforced. Steel core at one end as original.Width: 2.5 inches. Height: 1.625 inches.
Brake and Clutch Pedal Pads
p/n: 60-0068-22
Brake and Clutch Pedal Pads - The proper design and fully detailed with ribs extending down over sides of the pad. Length: 3.50 inches. Width: 2.0 inches.
Front Spring Rubber Bumper
p/n: 70-0329-32
Front Spring Rubber Bumper - for upper control arm on frame.
Hood to cowl weatherstrip
p/n: 60-0428-42
Anti-squeak, hood to cowl ledge. Two (2) pieces with holes, ready to install.Length: 21.0 inches. Width: .625 inches.
Run Channel Upper Bumper
p/n: 60-0183-62
Bumper, side window glass in vent frame at top, right and left, brass core.Length: 1.625 inches.
Headlight Door To Lens Seal
p/n: 70-0493-14
Headlight Door To Lens Seal - Molded without wire. Double lip type for sealed beam headlights. Note: Compare with our single lip type #70-0389-14 sold separately.
Rigid Run Channel
p/n: 70-0347-58
Stainless beaded edge, mohair-lined, exact replacement for rear side of division bar. Available in 15" pairs.
Beltline Weatherstrip
p/n: 70-0555-58
Weatherstrip, door window inner and outer, front and rear doors. Bend to fit. Available in a 3ft pair.
Quarter window bumper
p/n: 60-0669-62
Bumper, quarter window on body lock pillar.Though we haven't been able to determine a part number, this part is used on 1951 hardtops and convertibles.
Vent division bar weatherstrip
p/n: 60-0596-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Inner Fender Seal
p/n: 60-0288-45
Inner Fender Seal for anti-rattle, running board apron to body, or fender splash panels. Nine sixteenths (9/16) inch by seven eighths (7/8) inch slotted sponge rubber to accept rivets. Sold in eight (8) foot strips.
Bumper support bar pad
p/n: 60-0420-30
Pads, rear bumper bar, inner, to quarter panel. Fully molded rubber. Two and eleven sixteenths inch (2-11/16") outside length by one inch (1") outside width by one and five eighths inch (1-5/8") inside hole length by one fourth inch (1/4") inside hole wid
Rear spring bushing
p/n: 60-0311-35
Bushing, rear spring front eye, inlox cartridge type as original.
Sliding Quarter Window Weatherstrip
p/n: 70-0353-78
Weatherstrip, door window inner and outer, front and rear doors. Bend to fit. Available in a 6ft lengths.
Fenderskirt Edge Seal
p/n: 60-0109-45
Fenderskirt Edge Seal - One (1) ten (10) foot strip. Length: 120.0 inches.
Front suspension bumper
p/n: 50-0092-32
Bumper, front suspension, lower arm. Steel core, with threaded stud, as original. Two (2) per car required.
Front Stabilizer Bushing
p/n: 60-0088-34
Front Stabilizer Bushing - Front stabilizer bar mounting. Fully molded rubber. Two (2) required per car. One and five sixteenths inch (1 5/16") length by one and five sixteenths inch (1 5/16") width by five eighths inch (5/8") inside hole diameter by one and three fourths inch (1 3/4") height.
Hood to cowl weatherstrip
p/n: 70-1698-43
Weatherstrip, hood to cowl.Length: 47.0 inches. Width: .5625 inches. Height: .28125 inches.
Gravel shield anti-squeak
p/n: 60-0173-30
Seal, rear bumper face bar-to-body (gravel shield). Fully molded rubber with all original features. Seventy-nine inches (79") long. Extrusion ends measure one and three fourths inch (1-3/4") wide by nine sixteenths inch (9/16") height.
Side Window Sash Channel
p/n: 70-0641-58
Sash channel, side window glass. U-shaped steel channel only, no filler. Will require that you attach your own window regulator cam to underside as required.
Rigid Run Channel
p/n: 70-0516-58
Channel, rigid run, lower side window below beltline, zinc plated steel with black cloth lining. Available in 15" pairs.
Door weatherstrip
p/n: 60-0664-73
Weatherstrip, auxiliary on body lock pillar. Correct extrusion cut thirty (30) inches long.
Gravel shield bumper
p/n: 60-0146-30
Bumper, rear bumper deflector. Two (2) per car.Chevrolet 1942-55 Bumper, rubber, radiator grille, lower panel.Length: 2.1875 inches.
Exhaust system hanger
p/n: 60-0307-13
Support (insulator) muffler-to-tailpipe, webbing reinforced. One (1) per car.Length: 3.4 inches. Width: 1.0 inches.
Firewall grommet
p/n: 60-0565-20
Grommet, two hole type.Chevrolet 1949-54 Grommet, two hole type. Replaces #3708180.