This Rear Window Gasket mounts around the full perimeter of the back glass and has the divider bars molded directly into it. It has properly molded corners to precisely conform to the glass and has the slot to accommodate the outer edge's decorative molding.
This six (6) piece Front Door Vent Window Set contains the main vent window seals, base extensions, and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
This seven (7) piece Front Door Weatherstrip Set is the primary seal for the doors to the body. The set includes the door bottom weatherstrip with molded corners, hinge pillar bellows, front edge seals, and rear edge seals.
This Windshield Gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
This Front Door Vent Window Weatherstrips contain the main seals for the vent windows and the base extension pieces for the frame. They are designed and molded from original parts for superior fitment and seal.
This Windshield Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends.
This Revulcanization Service Only is designed to restore your Front Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Support retainer, transmission mounting at front cross member. One (1) required per car. Revulcanization service only.
Hinge Pillar Weatherstrip - Attaches to the body and seals between the A-pillar post and the front section of the door or vent window frame when the door is closed.
This Trunk Weatherstrip is designed from original parts for superior fitment and seal. The set contains the strips and corners that mount to the body and the strip that mounts to the lid.
Weatherstrip, door bottom and corners, molded right and left. Overall length forty and three fourths (40-3/4) inch per door.
Seat, rear spring. Revulcanization service only. Send in complete casting with metal sleeve bushing.
Bumpers, rear springs to frame. Revulcanization service only.Length: 3.0 inches. Width: 2.5 inches.
Weatherstrip, roof rail at hinge pillar.
Weatherstrip body hinge pillar
Weatherstrip, front door opening. Right and left, hinge pillar at beltline. Constructed of soft rubber.Length: 12.0 inches.
These trunk weatherstrip corners are designed from the original part for superior fitment and seal. The seals mount to the front corners of the trunk directly to the body.
Mounting pad, back up light. Fully molded left and right.
Cover (grommet), steering gear-to-toe board seal.Width: 5.8125 inches. Height: 6.0 inches.
Pad, taillight mounting.Length: 6.625 inches.
Bumper, door side. Square type held by four (4) screws, metal core as original.
Insulator (support), exhaust system, right angle type, fabric reinforced. Steel core at one end as original.Width: 2.5 inches. Height: 1.625 inches.
Brake and Clutch Pedal Pads - The proper design and fully detailed with ribs extending down over sides of the pad. Length: 3.50 inches. Width: 2.0 inches.
Front Spring Rubber Bumper Pair - for upper control arm on frame.
This Master Cylinder Access Hole Cover is designed from the original part for superior fitment and seal. Secures the Brake Master Cylinder Filler and Inspection Access Hole in the vehicle.
This Hood to Cowl Weatherstrip is designed from original parts so it fits correctly. The pair comes ready to install with pre-punched holes.
Bumper, side window glass in vent frame at top, right and left, brass core.Length: 1.625 inches.
Headlight Door To Lens Seal - Molded without wire. Double lip type for sealed beam headlights. Note: Compare with our single lip type #70-0389-14 sold separately.
Stainless beaded edge, mohair-lined, exact replacement for rear side of division bar. Available in 15" pairs.
These Window Felt Beltline Weatherstrips are sold as a three (3) foot pair. The beltline is used for side windows inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Pads, rear bumper bar, inner, to quarter panel. Fully molded rubber. Two and eleven sixteenths inch (2-11/16") outside length by one inch (1") outside width by one and five eighths inch (1-5/8") inside hole length by one fourth inch (1/4") inside hole wid
Inner Fender Seal for anti-rattle, running board apron to body, or fender splash panels. Nine sixteenths (9/16) inch by seven eighths (7/8) inch slotted sponge rubber to accept rivets. Sold in eight (8) foot strips.
Bushing, rear spring front eye, inlox cartridge type as original.
This Sliding Quarter Window Weatherstrip is used for side window inner and/or outer, front and/or rear doors. Available in a 6ft lengths.
Seal, rear spring seat. Four (4) piece set.Height: .1875 inches.
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish, and seal. This weatherstrips fits between the rear wheel fender skirt and the rear fender quarter panel.
Bumper, front suspension, lower arm. Steel core, with threaded stud, as original. Two (2) per car required.
Front Stabilizer Bushing - Front stabilizer bar mounting. Fully molded rubber. Two (2) required per car. One and five sixteenths inch (1 5/16") length by one and five sixteenths inch (1 5/16") width by five eighths inch (5/8") inside hole diameter by one and three fourths inch (1 3/4") height.
Headlight body mounting gasket. Rubber.
This Hood To Cowl Weatherstrip mounts at the rear of the engine bay to seal between the hood and vehicle body cowl. A reproduction designed from original part so it fits correctly.
This Rear Bumper Gravel Shield, also known as a rear bumper face bar-to-body seal, is made of high quality dense rubber. Fully molded rubber with all original features.
Sash channel, side window glass. U-shaped steel channel only, no filler. Will require that you attach your own window regulator cam to underside as required.
Weatherstrip, sash channel. Correct extrusion. Two (2) strips cut twenty five and one half (25-1/2) inches long.
Channel, rigid run, lower side window below beltline, zinc plated steel with black cloth lining. Available in 15" pairs.
Accelerator pedal. Steel core with hinge. Length: 8.9375 inches.
Weatherstrip, auxiliary on body lock pillar. Correct extrusion cut thirty (30) inches long.
Bumper, rear bumper deflector. Two (2) per car.Chevrolet 1942-55 Bumper, rubber, radiator grille, lower panel.Length: 2.1875 inches.
Support (insulator) muffler-to-tailpipe, webbing reinforced. One (1) per car.Length: 3.4 inches. Width: 1.0 inches.
Grommet, two hole type.Chevrolet 1949-54 Grommet, two hole type. Replaces #3708180.