This windshield gasket set contains the windshield gasket itself and the locking strip. The seal mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit.
Weatherstrip, front door kit. Includes weatherstrip for door perimeter and hinge pillars.
Weatherstrip, front door hinge pillar.
This front door vent window weatherstrip kit is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Engine support, front. Revulcanization service only.
Support, engine mount at rear. Revulcanization service only.
Bumper, front spring compression, lower arm. Steel core, retained by clip (not included).Height: 2.625 inches.
Bumper, front spring rebound, lower.Width: 2.125 inches. Height: 2.25 inches.
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Pedal, accelerator. Revulcanization service only. Includes new rod ball socket and pivot. Original pattern tread.Length: 9.625 inches. Width: 1.9375 inches.
Weatherstrip, hood to cowl. Fully molded with carrot-bumper retainers.Width: .625 inches.
Grommet, steering column at floorboard.Length: 4.50 inches.
Bumper, front spring rebound, upper.Height: 2.25 inches.
Pad or Gasket, taillight to body. One (1) pair required per car, sold only in pairs.
Retainer, intermediate bearing. All models with two piece driveshafts.
Bearings or bushings, front stabilizer rod. One (1) pair used per vehicle. Fully molded rubber. One and nine sixteenths inch (1 9/16") length by one and nine sixteenths inch (1 9/16") width by three fourths inch (3/4") inside hole diameter by one and elev
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Bushings, front stabilizer rod end. One (1) pair required per car. Fully molded rubber. One and one half inch (1 1/2") length by one and one eighth inch (1 1/8") width by three fourths inch (3/4") inside hole diameter by one and one half inch (1 1/2") hei
Grommet, ignition cable.Length: 2.125 inches. Width: 1.50 inches.
Weatherstrip, door window inner and outer, front and rear doors. Bend to fit. Available in a 3ft pair and 6ft piece.
Gaskets, headlight body mounting to fender. Cut to exact size as original.
Headlight body mounting gasket. Rubber.
Grommet, handbrake rod to dash.Height: 1.875 inches.
Grommet, wiring harness.
Gasket, rear bumper license plate lens. Machine die-cut from 1/16" rubber.Length: 6.5625 inches. Width: 1.625 inches.
Back-Up Light To Body Gaskets - A pair of top quality molded rubber seals manufactured to authentic original dimensions. These gaskets are designed and made for a precise, factory like fit and performance.
Boot, gearshift on steering column. Brown rubber. For black see our #30-0069-36. Two and one eighth (2-1/8) inch long style.
Tail Light Lens Gasket
Boot, gearshift on steering column. Black rubber. For brown see our #30-0069-89. Two and one eighth (2-1/8) inch long style.Length: 2.25 inches.
Boot, starter solenoid.
Grommet, carpet. Floor front carpet grommet use for power brake hole.
Pad, fender mounted antenna.Length: 2.5 inches.
Pad, body mounting. Fully molded rubber with metal core and rubber locating collar. Also used for radiator cradle to frame. Eight (8) to ten (10) required per car. Two and one fourth inch (2 1/4") outside diameter by one and one sixteenth inch (1 1/16") l
Cover, battery clamp. Control unsightly sulfate buildup. Help protect the nearby metal and finish. Good copy from original part.Length: 3.5 inches.
Bumper, hood, on side of fender. Six (6) required per car.Length: 1.0 inches. Width: 1.375 inches.
Grommet, antenna mounting. Fits all models with power antenna. Used with our #70-0756-19.
Bushing, rear stabilizer. Four (4) are required per car. Fully molded rubber. One and one half inch (1 1/2") outside diameter by five eighths inch (5/8") inside hole diameter by seven eighths inch (7/8") height.
Insulator, rear spring leaf clip. Seven and one half (7-1/2) inch long, customer may trim for shorter lengths. May use up to eight (8) per car.
Grommet, dimmer switch for carpet application.
Masticated sheet. Three thirty seconds (3/32) inch thick rubber sheet containing random milled cotton cord reinforcement for front end splash aprons, etc. This product is a four (4) foot wide roll, and will only be sold in four (4) square foot multiples
Knob, inside door lock control, flexible rubber, black only.Height: 1.125 inches.
Pad, body mounting. Fully molded rubber. Also used for radiator cradle to frame. Eight (8) to ten (10) required per car. Two and one eighth inch (2 1/8") outside diameter by three fourths inch (3/4") inside hole diameter by five sixteenths inch (5/16") he
Dust cover, tie rod ends.
Grommet, overdrive control linkage. Spool type grommet used on manual transmission models with factory overdrive. Three fourths inch (3/4") outside diameter by three eighths inch (3/8") inside hole diameter by three eighths inch (3/8") height.
Grommet, spark plug & coil wire at distributor cap outlets. For nine (9mm) millimeter wire, earlier years.
Cushion Horn BUTTON
Weatherstrip, door edge. Fine grain sponge. Larger type used on most GM cars this period. Available by the foot.
Trunk weatherstrip made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.