This kit includes the weatherstrip components needed for the glass on your restoration project.
This kit includes the major weatherstrip components and some other essential parts needed for the body of your restoration project.
This front door vent window weatherstrip set is a six (6) piece set that contains the main vent window seals, base extensions, and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
This front door vent window weatherstrip set contains the main seals for the vent windows and the base extension pieces for the frame. They are designed and molded from original parts for superior fitment and seal.
This windshield gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
Door edge weatherstrip with molded ends. This part is the primary door to body weatherstrip. Includes clips for easy installation.
This rear window gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Weatherstrip, front door opening, auxiliary on cowl at beltline. Right and left, brass core.
Bumper, rear axle. Revulcanization service only.Height: 3.5 inches.
Grommet, steering column to dash at floorboard. Black rubber. For brown see our #70-2516-89. Fully molded with correct metal core.
Grommet, steering column to dash at floorboard. Brown rubber. For black see our #70-2516-36. Fully molded with correct metal core.
Front motor mount. Revulcanizing core exchange only. Send in both pairs of the two piece cores when ordering.
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Support pad, transmission mount (insulator). Revulcanization service only.Length: 5.0 inches. Width: 2.0 inches.
Support, transmission (insulator). Revulcanization service only. See also our #50-0262-25, many models use both.Length: 5.0 inches. Width: 1.875 inches.
Pad, transmission mounting, thrust. Revulcanization service only. One (1) per car required. See also our #50-0263-25. Many models use both.Length: 7.
Retainer, torque ball, heavy steel jacket with molded rubber inner collar. Revulcanization service only.
A Rigid Run Channel pair with bright beaded edge, mohair lined channel, die trimmed and round formed at the top. Sold in 29" pairs.
Bumper, rear axle stop. Molded left and right. Revulcanization service only.
Weatherstrip, upper front door hinge pillar at roof rail. Molded rubber with brass core.Length: 3.75 inches.
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Weatherstrip, hood to cowl. 63 3/4" long.
Door lock pillar seal. This part seals the bottom of the rear side window, and may also be known as a door jamb seal.
Pad, trunk ornament mounting.Width: 21.0 inches.
Weatherstrip, front door auxiliary, on door at beltline, right and left. Uses snap-in fasteners, four (4) each included.
Boot, torque ball.Height: 2.375 inches.
Insulators, rear coil spring. Fabric reinforced rubber as original. One (1) pair per car.
Bumper, side window glass in vent frame at top, right and left, brass core.Length: 1.625 inches.
Stainless beaded edge, mohair-lined, exact replacement for rear side of division bar. Available in 15" pairs.
Weatherstrip, door window inner and outer, front and rear doors. Bend to fit. Available in a 3ft pair.
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Bumper, front suspension, upper arm.Height: 2.0 inches.
Pad, front coil spring insulator, upper. Two (2) per car, five and one eighths (5-1/8) inch outside diameter. Height: .28125 inches.
Bushings, front stabilizer shaft-to-frame or stabilizer shaft, front or rear. Fully molded rubber. One and one half inch (1 1/2") length by one and one half inch (1 1/2") width by eleven sixteenths inch (11/16") inside hole diameter by one and one half in
Pad, brake and clutch pedal. Brown rubber. For black see our part #50-0054-22. Perfect copy, fine detail.Color:brown Width: 3.125 inches.
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Seal, roof rail at quarter window. Fully molded with brass core.Length: 1.375 inches. Width: .6875 inches.
Weatherstrip, door window inner and outer, front and rear doors. Bend to fit. Available in a 6ft lengths.
Bumper, front suspension, lower arm. Steel core, with threaded stud, as original. Two (2) per car required.
Headlight body mounting gasket. Rubber.
Sash channel, side window glass. U-shaped steel channel only, no filler. Will require that you attach your own window regulator cam to underside as required.
Pedal pad, power brake only, slip-over.Width: 4.75 inches.
Weatherstrip, windshield post, upper to door. Seals between front door vent window frame and windshield pillar. Top quality rubber made to original cross-section. Two (2) strips approximately fifteen (15) inches long. May need to trim ends to fit.
Channel, rigid run, lower side window below beltline, zinc plated steel with black cloth lining. Available in 15" pairs.
Mounting pad, extrusion, taillight body-to-rear fender. Sold in sets sufficient for two (2) taillights.Length: 55.0 inches. Width: .3125 inches.
Pad, parking brake pedal. With "PARK" written on pad. Black only. For pedal pad without "PARK" written on pad see our #50-0348-22.Width: 2.0625 inches.
Seal, headlight to fender. Die cut to original dimensions.Height: .125 inches.
Grommet, brake and clutch pedal floor seal.Width: 1.8125 inches. Height: 2.375 inches.
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Pad, brake and clutch pedal. Black rubber. For brown see our part #50-0054-89. Perfect copy, fine detail.Width: 3.125 inches. Height: 2.125 inches.