This comprehensive twenty (20) piece Glass Weatherstrip Kit includes the weatherstrip components needed for the glass on your restoration project. These parts are designed from originals for superior performance and a factory fit.
This twenty-eight (28) piece Body Mounting Pad set is designed from the original parts for superior fitment and function. Designed from original parts, made from rubber with steel core.
This ten (10) piece Window Felt and Run Channel set includes the inner and outer window felts, upper and lower rigid run channels, and flexible run channels needed to complete two (2) doors.
This six (6) piece Body Weatherstrip Kit includes the major weatherstrip components needed for the body of your classic restoration vehicle. We’ve put everything together in one simple and convenient kit.
This Rear Side Window Weatherstrip set contains the left and right seals for the two (2) fixed windows on the rear side of the vehicle. The seals have properly molded corners for a precise, factory fit.
This Side Window Weatherstrip set contains the left and right seals for the two (2) fixed windows on the side of the vehicle. The seals have properly molded corners for a precise, factory fit.
This front door vent window weatherstrip set is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
This Front Door Weatherstrip pair is high quality sponge rubber with inserted nylon clips. Designed from the original part for superior fitment and seal. Each strip is approximately one hundred sixty six (166") inches long.
This windshield gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
This Automatic Transmission Mount pair supports the transmission and dampens vibration. Engineered and designed to OE standards. Steel core as original.
Seal, rear wheelhouse panel-to-quarter panel, outer. Two (2) five (5) foot strips, one for each side.Length: 60.0 inches. Width: .21875 inches.
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
This six (6) piece Door Auxiliary Weatherstrip set is designed from the original part for superior fitment and seal. The Auxiliary Weatherstrip, also known as a "J" seal, installs on the door front at the beltline, right and left sides of the vehicle.
Insulator (support), exhaust system, right angle type, fabric reinforced. Steel core at one end as original.Width: 2.5 inches. Height: 1.625 inches.
Brake and Clutch Pedal Pads - The proper design and fully detailed with ribs extending down over sides of the pad. Length: 3.50 inches. Width: 2.0 inches.
This Tailgate or Back Door Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts with properly spaced plastic clips around the full perimeter of the rear opening.
Headlight Door To Lens Seal - Molded without wire. Double lip type for sealed beam headlights. Note: Compare with our single lip type #70-0389-14 sold separately.
Stainless beaded edge, mohair-lined, exact replacement for rear side of division bar. Available in 15" pairs.
Front Suspension Rubber Bumper for the front suspension lower control arm (attaches to lower arm spring mount). This part is compatible to several Chevrolet model vehicles. Self-retaining, top quality. Height: 1.75 inches.
Cloth covered, mohair lined flexible metal channel for sides and top of door windows.
Accelerator Pedal Pad - Slip-over type made from top quality rubber. Length: 8.875 inches.
These Window Felt Beltline Weatherstrips are sold as a three (3) foot pair. The beltline is used for side windows inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Inner Fender Seal for anti-rattle, running board apron to body, or fender splash panels. Nine sixteenths (9/16) inch by seven eighths (7/8) inch slotted sponge rubber to accept rivets. Sold in eight (8) foot strips.
Cloth covered, mohair lined flexible metal channel for sides and top of door windows.
This Sliding Quarter Window Weatherstrip is used for side window inner and/or outer, front and/or rear doors. Available in a 6ft lengths.
Front Stabilizer Bushing - Front stabilizer bar mounting. Fully molded rubber. Two (2) required per car. One and five sixteenths inch (1 5/16") length by one and five sixteenths inch (1 5/16") width by five eighths inch (5/8") inside hole diameter by one and three fourths inch (1 3/4") height.
Headlight body mounting gasket. Rubber.
This Rear Bumper Gravel Shield, also known as a rear bumper face bar-to-body seal, is made of high quality dense rubber. Fully molded rubber with all original features.
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment and seal. This weatherstrips fits between the removable fender skirt and the rear fender quarter panel.
Sash channel, side window glass. U-shaped steel channel only, no filler. Will require that you attach your own window regulator cam to underside as required.
Cover, steering gear and clutch pedal push rod dash seal.Length: 8.625 inches. Width: 7.625 inches.
Channel, rigid run, lower side window below beltline, zinc plated steel with black cloth lining. Available in 15" pairs.
Filler, quarter window division bar, upper and lower. Fits into inside garnish molding between rear seat side window and rear side window.
Support (insulator) muffler-to-tailpipe, webbing reinforced. One (1) per car.Length: 3.4 inches. Width: 1.0 inches.
This Brake Master Cylinder Push Rod Boot is made from high-quality Nitrile rubber for a precise, factory like fit for your classic vehicle. Manufactured to OEM specifications to install for an authentic fit and finish.
Bumper, brake and clutch pedal shank, rides under floorboard. One and one eighth (1-1/8) inch clearance for pedal shaft. Compare with our #60-0579-24.
Pad and steel bushing assembly. Two (2) required per vehicle Rectangular rubber with metal core, locating collar and metal bolt. Two and seven sixteenths inch (2 7/16") length by one and three fourths inch (1 3/4") width by three fourths inch (3/4") ins
Bumper, front suspension, lower arm. Steel core as original, excellent quality.
This Hood To Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact copy reproduction of the original profile. This weatherstrip installs at the rear of the engine bay to seal between the hood and vehicle body cowl.
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt 3/8"-16 NF x 6-15/16" long. Comes with metal sleeve, metal cup washers and rubber grommets.
This black rubber Battery Clamp Cover helps to protect the nearby metal and finish. Good copy from an original part. Length: 3-1/2" inches.
Pad, body mounting. Rubber original type with metal core, locating collar and metal bolt liner. Two and one eighths inch (2 1/8") outside diameter by three fourths inch (3/4") inside bolt hole diameter by seven eighths inch (7/8") metal bolt outside diame
Mounting pad, radio antenna. Approximately one and one half (1-1/2) inch by four and five sixteenths (4-5/16) inch.Length: 4.3125 inches. Width: 1.
Bumper, hood rest. Self-retained in slot on fender ledge. Six (6) piece set.Width: .5625 inches. Height: .78125 inches.
Grommet, cowl gutter drain hose. Nine sixteenth (9/16) inch hole through cowl side wall, five sixteenths (5/16) inch inside diameter. Two (2) per car.
Boot, solenoid plunger, starter switch at starter.Height: 1.625 inches.
This Standard Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability.
This part is used as a front window regulator or accelerator rod through toe board seal. A front window regulator seal for 1955-60 passenger cars with electric windows and for 1957-62 Corvette models. Used as an accelerator rod through toeboard seal for 1955-62 V8 only Corvettes.