Search Results
Please click on the part name in red in order to get a complete description.
Glass Weatherstrip Kit
p/n: 90-3074-90
This kit includes the weatherstrip components needed for the glass on your restoration project.
Glass Weatherstrip Kit
p/n: 90-3072-90
This kit includes the weatherstrip components needed for the glass on your restoration project.
Body Weatherstrip Kit
p/n: 90-3088-90
This kit includes the major weatherstrip components and some other essential parts needed for the body of your restoration project.
Body Weatherstrip Kit
p/n: 90-3087-90
This kit includes the major weatherstrip components and some other essential parts needed for the body of your restoration project.
Front Door Vent Window Kit
p/n: 90-0431-90
This front door vent window weatherstrip kit is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Rear Window Gasket
p/n: 50-0281-81
This rear window gasket mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit.
Windshield Gasket
p/n: 70-1875-50
This windshield gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation. It also has the slot to accommodate the outer edge's decorative molding.
Front Door Vent Window Weatherstrips
p/n: 38-0098-55
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Door weatherstrip
p/n: 50-0458-72
Door edge weatherstrip with molded ends. Clip on type. This part is the primary door to body weatherstrip. Includes pins and fasteners for easy installation.
Windshield Gasket
p/n: 50-0212-50
This windshield gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation. It also has the slot to accommodate the top edge's decorative molding.
Door weatherstrip
p/n: 50-0440-72
Door edge weatherstrip with molded ends. Glue in type. Four (4) piece set with fourteen (14) clips. This part is the primary door to body weatherstrip.
Motor mount service
p/n: 25-0072-11
Insulator, cushion assembly. Engine mount at bell housing, right and left. Revulcanization service only.Length: 5.25 inches.
Motor mount service
p/n: 25-0059-11
Motor mounts, rear at transmission, right and left. Revulcanization service only.Length: 5.25 inches.
Motor mount service
p/n: 25-0063-11
Motor mount, upper, engine bracket at front cross member. One (1) per vehicle. Revulcanization service only.Length: 6.1875 inches. Width: 2.875 inches.
Motor mount service
p/n: 25-0073-11
Insulator, engine mount, front lower. Revulcanization service only.Length: 5.125 inches.
Roof rail filler
p/n: 25-0069-73
Weatherstrip, front door upper corner, outer (at front end of flipper). Right and left, brass core.Length: 5.625 inches.
Trunk Weatherstrip
p/n: 50-0483-84
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid.
U Jamb lock pillar filler
p/n: 50-0307-79
Door lock pillar seal. This part seals the bottom of the rear side window, and may also be known as a door jamb seal.
Fenderskirt edge seal
p/n: 25-0092-44
Seal, fender skirt. Two 5 foot lengths of extrusion.Length: 60. inches. Width: .9375 inches.
Hood To Cowl Weatherstrip
p/n: 70-0940-42
Weatherstrip, hood to cowl. An exact reproduction of the original profile. This seal mounts at the rear of the engine bay directly to the body.
Door Auxiliary Weatherstrip
p/n: 60-0342-73
Weatherstrip, front door, auxiliary on door front at beltline, right and left. Held on by button fasteners (our #50-0198-73, four (4) each included in set). Also known as a "J" seal.
Front Stablizer Bar End Link Kit
p/n: 70-0567-34
Kit, stabilizer bar link assembly. Twenty two (22) piece set for both sides of one (1) car, front and rear. (Order 2 sets if you need both). Hex head bolt. 5/16"-24nf x 7-5/8" lg. Comes with metal sleeve, cup washers and rubber grommets.
Front Spring Rubber Bumper
p/n: 70-0329-32
Front Spring Rubber Bumper - for upper control arm on frame.
Run Channel Upper Bumper
p/n: 60-0183-62
Bumper, side window glass in vent frame at top, right and left, brass core.Length: 1.625 inches.
Motor (Engine) Mount
p/n: 25-0060-11
Motor (engine) mount, lower front. One (1) per car. Length: 4.50 inches.
Rigid Run Channel
p/n: 70-0347-58
Channel, rigid run, window division bar. Stainless beaded edge, mohair-lined, exact replacement for rear side of division bar.
Beltline weatherstrip
p/n: 70-0555-58
Weatherstrip, door window inner and outer, front and rear doors. Seven sixteenths (7/16) inch wide, with chrome bead, mohair faced, flexible. Two (2) three (3) foot strips. Bend to fit.
Gearshift boot
p/n: 70-2126-24
Boot, transmission gear hand shift lever. Molded in pliable black rubber which may be painted if needed for restoration.
Vent division bar weatherstrip
p/n: 50-0518-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Front stabilizer bushing
p/n: 50-0094-34
Bushings, front stabilizer shaft-to-frame or stabilizer shaft, front or rear. Fully molded rubber. One and one half inch (1 1/2") length by one and one half inch (1 1/2") width by eleven sixteenths inch (11/16") inside hole diameter by one and one half in
Fenderskirt edge seal
p/n: 60-0201-45
Seal, fenderskirt edge. Proper profile for most skirts of this period, including Fox-Craft. Sixty (60) inch strip.Length: 60. inches. Width: .75 inches.
Steel sash channel
p/n: 70-0641-58
Sash channel, side window glass. U-shaped steel channel only, no filler. Will require that you attach your own window regulator cam to underside as required.
Windshield post to door seal
p/n: 70-0304-73
Weatherstrip, windshield post, upper to door. Seals between front door vent window frame and windshield pillar. Top quality rubber made to original cross-section. Two (2) strips approximately fifteen (15) inches long. May need to trim ends to fit.
Rigid run channel
p/n: 70-0516-58
Channel, rigid run, lower side window below beltline, zinc plated steel with black cloth lining, one half (1/2) inch deep by one half (1/2) inch wide, fifteen (15) inches long.
Door Flipper Stop
p/n: 70-2853-62
This Door Flipper Stop is designed from the original part for superior fitment and seal. The rear flipper stop mounts inside the flipper opening at the very rear of the door flipper.
Roof rail filler
p/n: 70-1763-73
Weatherstrip seal, roof rail, outer at quarter window.Length: 1.125 inches. Width: .75 inches.
Brake & Clutch Pedal Pads
p/n: 25-0058-22
Pads, brake and clutch pedal. Two (2) per car. Length: 4.0 inches. Width: 2.5 inches.
Headlight Outer Rim Seal
p/n: 27-0063-14
Headlight Outer Rim Seal - Used to seal the headlight beam retainer ring. Replaces # 5945844.
Splash apron
p/n: 70-3064-45
Filler, splash apron. A-arm dust shield two (2) piece set. Die cut masticated rubber. Includes all factory style holes required for installation.
Quarter Window Leading Edge Weatherstrip
p/n: 70-0141-58
This Leading Edge Vertical Weatherstrip seal pair is designed from the original part for superior fitment and seal. Slides into metal retaining channel attached to rear side window and seals between the front door window and the rear quarter window.
Body mounting pad
p/n: 27-0092-48
Insulator, body mounting pad. Metal core & locating collar covered with rubber. Two inch (2") square by fifteen sixteenths inch (15/16") locating collar outside diameter by five eighths inch (5/8") locating collar inside hole diameter. Seven sixteenths in
Battery clamp cover
p/n: 70-0095-21
Cover, battery clamp. Control unsightly sulfate buildup. Help protect the nearby metal and finish. Good copy from original part.Length: 3.5 inches.
Rocker panel dust shield cover
p/n: 70-2392-45
Cover, rocker panel inner dust shield. Fully molded with proper attaching teeth and flap.
Solenoid plunger boot
p/n: 60-0567-21
Boot, solenoid plunger, starter switch at starter.Height: 1.625 inches.
Hood bumper
p/n: 25-0068-42
Bumper, hood to fender, side.Length: 1.1875 inches. Width: .8125 inches.
Masticated rubber sheet
p/n: 70-0645-45
Masticated sheet. Three thirty seconds (3/32) inch thick rubber sheet containing random milled cotton cord reinforcement for front end splash aprons, etc. This product is a four (4) foot wide roll, and will only be sold in four (4) square foot multiples
Wiring grommet
p/n: 70-0355-14
Grommet, electric wire into light body under fenders, for headlights, taillights, some parking lights and auxiliary (fog) lights. Fits seven eighths (7/8) inch hole in light body. Two (2) to eight (8) per car as required.
Window stop stem bumper
p/n: 33-0622-62
Bumper, window stop. One and one fourth (1-1/4) inch square by one half (1/2) inch thick. Compare with our #33-0540-62 and #33-0675-62.Length: 1.
Door bumper
p/n: 50-0203-41
Bumper, fuel filler door, rear fender. With steel core, screw retained two (2) per car.Width: .5 inches. Height: .625 inches.
Glovebox link bumper
p/n: 50-0367-88
Bumper, glove box check link. Fits on glove box door arm as needed.Length: .75 inches. Width: .5625 inches. Height: .3125 inches.
Window stop stem bumper
p/n: 33-0540-62
Cushion (stem bumper), window stop, lower. For front and rear door, rear side and quarter windows as required.
Body Bolt Cushion
p/n: 60-0189-48
Pad, for each body bolt under frame bracket, to cushion washer and nut. Fully molded rubber. One and seven eighths inch (1 7/8") outside diameter by seven eighths inch (7/8") inside hole diameter by nine sixteenths inch (9/16) height.
Door Weatherstrip w/ Clips (Sponge Rubber Extrusion - General Use)
p/n: 70-1112-73
Door edge weatherstrip made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models.
Brown door lock knob
p/n: 70-0660-70
Knob or push button for inside door lock, fits over 1/8" steel rod to door lock. Hard brown rubber, may be lacquered other colors as required.
Trunk Weatherstrip (Sponge Rubber Extrusion - General Use)
p/n: 70-0463-85
Trunk weatherstrip made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models.
Run channel mohair liner
p/n: 70-2863-58
Liner, mohair. Liner with a rubber backing. Apply with adhesive to division bars and channels. Helps reline guide bars on lock side of hardtops and convertibles.
Brown door lock knob
p/n: 70-0354-70
Knob for inside door lock control rod. Neutral brown color rubber, 3/32 inch hole. See also our #70-0660-70.
Shock and stabilizer grommet
p/n: 70-0274-33
Grommet, shock and stabilizer link. Eight (8) required per car. Fully molded rubber with locating collar. One and one sixteenth inch (1 1/16") outside diameter by nine sixteenths inch (9/16") locating collar outside diameter by three eighths inch (3/8") i
Universal mounting pad
p/n: 70-0308-17
Mounting pad, continuous for lights, hinges, brackets, and other bright work when no molded pad is available.
Body hole plug
p/n: 35-0863-45
Plug, body sheet metal holes. Used in various places (like trunks). For one and one half (1-1/2) inch hole in body.
Door Weatherstrip w/o Clips (Sponge Rubber Extrusion - General Use)
p/n: 70-1111-73
Door edge weatherstrip made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models.
Door weatherstrip
p/n: 70-0219-73
Weatherstrip, door edge, constant section on some models. Five eighths (5/8) inch by (5/8) inch cross-section, high grade, fine grain sponge rubber.
Sash channel filler 1/16 cork
p/n: 70-1115-57
Filler strip, window glass sash channel. One sixteenths (1/16) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherstrip type of filler. This is the highest quality linen back, rubber cork composition on
Firewall retainer
p/n: 60-0586-20
Retainer, firewall insulation panel. "Christmas Tree" style popular during this time. Constructed of vinyl plastic. Up to ten (10) required per car.
Door lock bumper
p/n: 34-0484-71
Bumper, door lock post, upper, one half (1/2) inch diameter by one half (1/2) inch tall, plated screw.Height: .50 inches.
Sash Channel Filler 1/16 Rubber
p/n: 70-2170-57
Filler strip, window glass sash channel. One sixteenths (1/16) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherlip type of filler. This is the highest quality rubber like polymer designed for settin
Door or tailgate bumper
p/n: 33-1228-71
Bumper pads, door or tailgate. Twin retainer style. Three eighths (3/8) inch by seven eighths (7/8) inch by one half (1/2) inch high.
Sash channel filler 1/32 cork
p/n: 70-1114-57
Filler strip, window glass sash channel. One thirty seconds (1/32) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherlip type of filler. This is the highest quality linen back, rubber cork composition
Sash Channel Filler 1/32 Rubber
p/n: 70-2169-57
Filler strip, window glass sash channel. One thirty seconds (1/32) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherlip type of filler.
Door bumper
p/n: 33-1227-71
Bumper, door edge, twin retainer style, three eighths (3/8) inch wide by seven eighths (7/8) inch long by three eighths (3/8) inch high.
Shock absorber bushing
p/n: 70-0547-32
Bushing, shock absorber mounting. Double cone style, rear. Five eighths (5/8) inch hole, one and one sixteenths (1-3/16) inch outside diameter, three fourth (3/4) inch thick.
Side window lift limit cap
p/n: 60-0071-62
Caps, side window lift limit. Rubber, snap-over type, three fourths (3/4) inch diameter by five sixteenths (5/16) inch thick.
Sash channel weatherstrip
p/n: 70-0585-58
Weatherstrip, sash channel, outer, for side windows, one half (1/2) inch wide weatherlip (cross section).Width: .50 inches.
Trunk floor pan plug
p/n: 35-0070-87
Plug, trunk and floor pan drain hole. Buick 1950-65 Plug, trunk and floor pan drain hole.
Door weatherstrip fastener
p/n: 60-0260-73
Clip, retainer for door edge weatherstrip. Two (2) prong type with oval screw hole, spring steel, cadmium plated.Width: .875 inches. Height: .9375 inches.
Hood bumper
p/n: 70-0294-42
Bumper, hood rest, cap type for adjustable screw, fifteenth sixteenths (15/16) inch, seven sixteenths (7/16) inch thick.
Wiring grommet
p/n: 32-0366-53
Grommet, windshield wiper control cable or gas gauge wire through rear compartment pan. Sheet Metal Hole: 7/16" Center Hole: 1/8" Outside Diameter: 5/8" Slot Width: 1/16"
Door weatherstrip fastener
p/n: 50-0198-73
Fastener, door edge weatherstrip, steel. One half (1/2) inch long, thirteen thirty second (13/32) inch diameter head, black finish.
