Search Results
Please click on the part name in red in order to get a complete description.
Glass Weatherstrip Kit
p/n: 90-3071-90
This kit includes the weatherstrip components needed for the glass on your restoration project.
Body Weatherstrip Kit
p/n: 90-3103-90
This kit includes the major weatherstrip components and some other essential parts needed for the body of your restoration project.
Side window run channel kit
p/n: 90-0141-58
This ten (10) piece kit includes the inner and outer windowfelts, upper and lower rigid run channels, and flexible run channels needed to complete two (2) doors. Used for front or rear doors in models with vent windows in the door.
Windshield Gasket
p/n: 70-1875-50
This windshield gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation. It also has the slot to accommodate the outer edge's decorative molding.
Front Door Vent Window Kit
p/n: 90-0418-90
This front door vent window weatherstrip kit is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Steering column floorplate
p/n: 70-2578-36
Floor plate, steering column at floorboard. Durable black rubber construction with metal core just like original.
Axle rebound pad
p/n: 50-0371-35
Bumper, rear axle. Revulcanization service only.Height: 3.5 inches.
Front Door Vent Window Weatherstrips
p/n: 38-0081-55
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Motor Mount
p/n: 50-0274-11
Front motor mount. Revulcanizing core exchange only. Send in both pairs of the two piece cores when ordering.
Door weatherstrip
p/n: 50-0533-72
Door edge weatherstrip, front or rear door. Fits front doors for all vehicles on the list. Also used on rear doors but ONLY for 1955-1956 Buick Century & Special 4dr wagons. Clip on type. This part is the primary door to body weatherstrip. Includes pins f
Transmission mount service
p/n: 50-0264-25
Support pad, transmission mount (insulator). Revulcanization service only.Length: 5.0 inches. Width: 2.0 inches.
Transmission mount service
p/n: 50-0263-25
Support, transmission (insulator). Revulcanization service only. See also our #50-0262-25, many models use both.Length: 5.0 inches. Width: 1.875 inches.
Transmission mount service
p/n: 50-0262-25
Pad, transmission mounting, thrust. Revulcanization service only. One (1) per car required. See also our #50-0263-25. Many models use both.Length: 7.
Torque ball service
p/n: 50-0190-27
Retainer, torque ball, heavy steel jacket with molded rubber inner collar. Revulcanization service only.
Rigid run channel
p/n: 70-0536-58
Run channel, front door window, for full length of division bar (approximately twenty nine (29) inches). Rigid, bright beaded edge, mohair lined channel, die trimmed and formed at top.
Axle rebound pad
p/n: 50-0370-35
Bumper, rear axle stop. Molded left and right. Revulcanization service only.
Rear Window Gasket
p/n: 60-0469-81
This rear window gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Hood To Cowl Weatherstrip
p/n: 50-0561-43
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. This seal mounts at the rear of the engine bay to seal between the hood and vehicle body cowl. Part is pre-drilled with 12 holes and includes button retainers.
Door Auxiliary Weatherstrip
p/n: 60-0342-73
Weatherstrip, front door, auxiliary on door front at beltline, right and left. Held on by button fasteners (our #50-0198-73, four (4) each included in set). Also known as a "J" seal.
Rear coil spring pad
p/n: 50-0359-35
Insulators, rear coil spring. Fabric reinforced rubber as original. One (1) pair per car.
Rigid Run Channel
p/n: 70-0347-58
Channel, rigid run, window division bar. Stainless beaded edge, mohair-lined, exact replacement for rear side of division bar.
Flexible Run Channel 6 Foot
p/n: 70-1239-58
Window run channel with stainless beaded edge. Six (6) foot length. Cloth covered, mohair lined, flexible channel for sides and top of door windows. Exact replacement for listed vehicles but can be used in many applications.
Beltline weatherstrip
p/n: 70-0555-58
Weatherstrip, door window inner and outer, front and rear doors. Seven sixteenths (7/16) inch wide, with chrome bead, mohair faced, flexible. Two (2) three (3) foot strips. Bend to fit.
Vent division bar weatherstrip
p/n: 60-0534-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Front Coil Spring Pad
p/n: 50-0476-35
Pad, front coil spring insulator, upper. Two (2) per car, five and one eighths (5-1/8) inch outside diameter. Height: .28125 inches.
Front stabilizer bushing
p/n: 50-0094-34
Bushings, front stabilizer shaft-to-frame or stabilizer shaft, front or rear. Fully molded rubber. One and one half inch (1 1/2") length by one and one half inch (1 1/2") width by eleven sixteenths inch (11/16") inside hole diameter by one and one half in
Flexible Run Channel 5 Foot
p/n: 70-1238-58
Window run channel, stainless beaded edge. Cloth covered, mohair lined flexible metal channel for sides and top of door windows. Perfect dimensions, Five eighths (5/8) inch wide by nine sixteenths (9/16) inch overall height, exact replacement. Five (5) fo
Sliding Quarter Window Weatherstrip
p/n: 70-0353-78
Weatherstrip, inner and outer for sliding quarter window, chrome beaded, mohair faced, flexible stock. May be formed to required outline. Six (6) foot strip.
Front suspension bumper
p/n: 50-0092-32
Bumper, front suspension, lower arm. Steel core, with threaded stud, as original. Two (2) per car required.
Steel sash channel
p/n: 70-0641-58
Sash channel, side window glass. U-shaped steel channel only, no filler. Will require that you attach your own window regulator cam to underside as required.
Rigid run channel
p/n: 70-0516-58
Channel, rigid run, lower side window below beltline, zinc plated steel with black cloth lining, one half (1/2) inch deep by one half (1/2) inch wide, fifteen (15) inches long.
Taillight mounting pad
p/n: 50-0100-15
Mounting pad, extrusion, taillight body-to-rear fender. Sold in sets sufficient for two (2) taillights.Length: 55.0 inches. Width: .3125 inches.
Parking brake pedal pad
p/n: 50-0405-22
Pad, parking brake pedal. With "PARK" written on pad. Black only. For pedal pad without "PARK" written on pad see our #50-0348-22.Width: 2.0625 inches.
Door handle gasket kit
p/n: 70-2673-69
Gasket set, front or rear door handles. Machine die cut from long lasting thin stock rubber. Six (6) piece set for two (2) doors.
Headlight Outer Rim Seal
p/n: 27-0063-14
Headlight Outer Rim Seal - Used to seal the headlight beam retainer ring. Replaces # 5945844.
Firewall grommet
p/n: 70-2067-20
Grommet, main wiring harness through firewall. Excellent reproduction of original.Width: 3.1875 inches. Height: .6875 inches.
Body mounting pad
p/n: 50-0477-48
Pad, body mounting. Fully molded rubber with metal core & locating collar. One and seven eighths inch (1 7/8") outside diameter by one and one eighths inch (1 1/8") locating collar outside diameter by three fourths inch (3/4") locating collar inside diame
Firewall grommet
p/n: 70-2066-24
Grommet, emergency brake cable through firewall. Excellent reproduction of original.Width: 2.5 inches.
Battery clamp cover
p/n: 70-0095-21
Cover, battery clamp. Control unsightly sulfate buildup. Help protect the nearby metal and finish. Good copy from original part.Length: 3.5 inches.
Firewall grommet
p/n: 70-2063-20
Grommet, speedometer cable line through firewall. Excellent reproduction of original.
Firewall grommet
p/n: 70-2062-20
Grommet, oil pressure and temperature line through firewall. Excellent reproduction of original.
Firewall grommet
p/n: 70-2064-20
Grommet, vacuum hose and ignition resistor wire through firewall. Excellent reproduction of original.
Window stop stem bumper
p/n: 33-0675-62
Cushion (stem bumper), window stop, lower. For front and rear door, rear side and quarter windows as required. (See sketch and our #33-0540-62).
Body mounting pad
p/n: 50-0096-48
Pad, body mounting. Fully molded rubber with steel core and locating collar. Two inch (2") square by one and one eighth inch (1 1/8") locating collar outside diameter by eleven sixteenths inch (11/16") locating collar inside diameter by one half inch (1/2
Rear coil spring pad
p/n: 50-0304-35
Insulator, rear coil spring clamp bolt (upper end). Two (2) per car. Fabric reinforced rubber as original.
Glovebox door check grommet
p/n: 70-0968-88
Grommet, glove box door cushion. One and three quarters long (1-3/4") and thirteen sixteenths (13/16")wide.Length: 1.75 inches. Width: .8125 inches.
Masticated rubber sheet
p/n: 70-0645-45
Masticated sheet. Three thirty seconds (3/32) inch thick rubber sheet containing random milled cotton cord reinforcement for front end splash aprons, etc. This product is a four (4) foot wide roll, and will only be sold in four (4) square foot multiples
Strut rod bushing
p/n: 50-0522-27
Bushing, strut rod at drive shaft tube. Two (2) per car required.Length: 1.65625 inches.
Body mounting pad
p/n: 50-0097-48
Pad, several useages. Use as a body mounting pad or as a cushion for body mounting bolt. Fully molded rubber. Up to twenty (20) required per car. Two inches (2") outside diameter by three fourths inch (3/4") inside hole diameter by one half inch (1/2") he
Axle rebound pad
p/n: 50-0302-35
Bushing, rear axle, anti-sway rod ends. Fully molded rubber. Four (4) required per car. One and one fourth inch (1 1/4") top outside diameter by one and one eighth inch (1 1/8") bottom outside diameter by five eighths inch (5/8") inside hole diameter by t
Hood bumper
p/n: 50-0095-42
Bumper, hood to fender ledge. Self retaining type. See our # 50-0194-42 for center type.
Firewall grommet
p/n: 70-2065-20
Grommet, cowl side hole stopper. Excellent reproduction of original.
Door bumper
p/n: 50-0203-41
Bumper, fuel filler door, rear fender. With steel core, screw retained two (2) per car.Width: .5 inches. Height: .625 inches.
Glovebox link bumper
p/n: 50-0367-88
Bumper, glove box check link. Fits on glove box door arm as needed.Length: .75 inches. Width: .5625 inches. Height: .3125 inches.
Window stop stem bumper
p/n: 33-0540-62
Cushion (stem bumper), window stop, lower. For front and rear door, rear side and quarter windows as required.
Door Weatherstrip w/ Clips (Sponge Rubber Extrusion - General Use)
p/n: 70-1112-73
Door edge weatherstrip made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models.
Shift lever grommet
p/n: 50-0284-24
Grommet, shift lever insulator. One (1) per car. Three eighths (3/8) inch inside diameter by five eighths (5/8) inch barrel by one half (1/2) inch long.
Brown door lock knob
p/n: 70-0660-70
Knob or push button for inside door lock, fits over 1/8" steel rod to door lock. Hard brown rubber, may be lacquered other colors as required.
Universal mounting pad
p/n: 70-0308-17
Mounting pad, continuous for lights, hinges, brackets, and other bright work when no molded pad is available.
Body hole plug
p/n: 35-0863-45
Plug, body sheet metal holes. Used in various places (like trunks). For one and one half (1-1/2) inch hole in body.
Door Weatherstrip w/o Clips (Sponge Rubber Extrusion - General Use)
p/n: 70-1111-73
Door edge weatherstrip made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models.
Window Gasket Weatherstrip
p/n: 60-0059-83
This window gasket weatherstrip was designed from an original part for a specific application but has many uses outside of its original purpose. The seal is structured to be used with 1/4" glass in a 3/8" channel. Most often used for rear quarter windows and rear windows.
Door weatherstrip
p/n: 70-0219-73
Weatherstrip, door edge, constant section on some models. Five eighths (5/8) inch by (5/8) inch cross-section, high grade, fine grain sponge rubber.
Sash channel filler 1/16 cork
p/n: 70-1115-57
Filler strip, window glass sash channel. One sixteenths (1/16) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherstrip type of filler. This is the highest quality linen back, rubber cork composition on
Firewall retainer
p/n: 60-0586-20
Retainer, firewall insulation panel. "Christmas Tree" style popular during this time. Constructed of vinyl plastic. Up to ten (10) required per car.
Door lock bumper
p/n: 34-0484-71
Bumper, door lock post, upper, one half (1/2) inch diameter by one half (1/2) inch tall, plated screw.Height: .50 inches.
Sash Channel Filler 1/16 Rubber
p/n: 70-2170-57
Filler strip, window glass sash channel. One sixteenths (1/16) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherlip type of filler. This is the highest quality rubber like polymer designed for settin
Door or tailgate bumper
p/n: 33-1228-71
Bumper pads, door or tailgate. Twin retainer style. Three eighths (3/8) inch by seven eighths (7/8) inch by one half (1/2) inch high.
Firewall grommet
p/n: 32-0365-20
Grommet, firewall, vent control cable. Sheet Metal Hole: 1/2" Center Hole: 3/16" Outside Diameter: 3/4" Slot Width: 1/16"
Sash Channel Filler 1/32 Rubber
p/n: 70-2169-57
Filler strip, window glass sash channel. One thirty seconds (1/32) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherlip type of filler.
Sash Channel Filler, 1/32" Cork
p/n: 70-1114-57
Filler strip, window glass sash channel. One thirty seconds (1/32) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherlip type of filler. This is the highest quality linen back, rubber cork composition
Door bumper
p/n: 33-1227-71
Bumper, door edge, twin retainer style, three eighths (3/8) inch wide by seven eighths (7/8) inch long by three eighths (3/8) inch high.
Shock absorber bushing
p/n: 70-0547-32
Bushing, shock absorber mounting. Double cone style, rear. Five eighths (5/8) inch hole, one and one sixteenths (1-3/16) inch outside diameter, three fourth (3/4) inch thick.
Firewall Grommet
p/n: 35-0369-20
Grommet, shroud or cowl upper panel gauge holes and for various body holes requiring grommet.
Trunk floor pan plug
p/n: 35-0070-87
Plug, trunk and floor pan drain hole. Buick 1950-65 Plug, trunk and floor pan drain hole.
Hood bumper
p/n: 70-0294-42
Bumper, hood rest, cap type for adjustable screw, fifteenth sixteenths (15/16) inch, seven sixteenths (7/16) inch thick.
Wiring grommet
p/n: 32-0366-53
Grommet, windshield wiper control cable or gas gauge wire through rear compartment pan. Sheet Metal Hole: 7/16" Center Hole: 1/8" Outside Diameter: 5/8" Slot Width: 1/16"
Hood & Door bumper
p/n: 33-0459-42
Bumper, hood to cowl and door hinge pillar upper. May be used in both places.
Door weatherstrip fastener
p/n: 50-0198-73
Fastener, door edge weatherstrip, steel. One half (1/2) inch long, thirteen thirty second (13/32) inch diameter head, black finish.
Fastener - Hood To Cowl Weatherstrip
p/n: 70-0564-42
A quality plastic button-head push-in fastener with self-retaining barbs. Typically used for hood to cowl weatherstrips, but also has other uses. The fastener length is three-fourths (3/4") inch with a five-eights (5/8") inch smooth button-head. Will fit a five-sixteenths (5/16') inch hole.
Cable or Wire Grommet
p/n: 32-0158-17
This Grommet is designed from the original part for superior fitment and seal. The grommet works for the hand brake cable through firewall or license light through trunk. Sheet Metal Hole: 9/16" Center Hole: 5/16" Outside Diameter: 13/16" Slot Width: 1/16"