Search Results
Glass Weatherstrip Kit
p/n: 90-3074-90
This kit includes the weatherstrip components needed for the glass on your restoration project.
Body Weatherstrip Kit
p/n: 90-3100-90
This kit includes the major weatherstrip components and some other essential parts needed for the body of your restoration project.
Front Door Vent Window Set
p/n: 90-0431-90
This front door vent window weatherstrip set is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Rear Window Gasket
p/n: 50-0281-81
This rear window gasket mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit.
Windshield Gasket
p/n: 70-1875-50
This windshield gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation. It also has the slot to accommodate the outer edge's decorative molding.
Front Door Vent Window Weatherstrips
p/n: 38-0098-55
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Door weatherstrip
p/n: 50-0458-72
Door edge weatherstrip with molded ends. Clip on type. This part is the primary door to body weatherstrip. Includes pins and fasteners for easy installation.
Steering column floorplate
p/n: 70-2578-36
Floor plate, steering column at floorboard. Durable black rubber construction with metal core just like original.
Axle rebound pad
p/n: 50-0371-35
Bumper, rear axle. Revulcanization service only.Height: 3.5 inches.
Motor Mount
p/n: 50-0274-11
Front motor mount. Revulcanizing core exchange only. Send in both pairs of the two piece cores when ordering.
Transmission mount service
p/n: 50-0264-25
Support pad, transmission mount (insulator). Revulcanization service only.Length: 5.0 inches. Width: 2.0 inches.
Transmission mount service
p/n: 50-0263-25
Support, transmission (insulator). Revulcanization service only. See also our #50-0262-25, many models use both.Length: 5.0 inches. Width: 1.875 inches.
Transmission mount service
p/n: 50-0262-25
Pad, transmission mounting, thrust. Revulcanization service only. One (1) per car required. See also our #50-0263-25. Many models use both.Length: 7.
Trunk emblem mounting pad
p/n: 50-0122-17
Mounting pad set, Trunk ornament. Three (3) piece set to replace original twenty six (26) inch single type, perfect fit.Width: 26.0 inches.
Torque ball service
p/n: 50-0190-27
Retainer, torque ball, heavy steel jacket with molded rubber inner collar. Revulcanization service only.
Roof rail filler
p/n: 25-0069-73
Weatherstrip, front door upper corner, outer (at front end of flipper). Right and left, brass core.Length: 5.625 inches.
Trunk Weatherstrip
p/n: 50-0483-84
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid.
Rigid Run Channels
p/n: 70-0536-58
A Rigid Run Channel pair with bright beaded edge, mohair lined channel, die trimmed and round formed at the top. Sold in 29" pairs.
Axle rebound pad
p/n: 50-0370-35
Bumper, rear axle stop. Molded left and right. Revulcanization service only.
U Jamb lock pillar filler
p/n: 50-0307-79
Door lock pillar seal. This part seals the bottom of the rear side window, and may also be known as a door jamb seal.
Hood to Cowl Weatherstrip
p/n: 50-0561-43
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. This seal mounts at the rear of the engine bay to seal between the hood and vehicle body cowl. Part is pre-drilled with 12 holes and includes button retainers.
Door Auxiliary Weatherstrip
p/n: 60-0342-73
Weatherstrip, front door, auxiliary on door front at beltline, right and left. Held on by button fasteners (our #50-0198-73, four (4) each included in set). Also known as a "J" seal.
Rear coil spring pad
p/n: 50-0359-35
Insulators, rear coil spring. Fabric reinforced rubber as original. One (1) pair per car.
Run Channel Upper Bumper
p/n: 60-0183-62
Bumper, side window glass in vent frame at top, right and left, brass core.Length: 1.625 inches.
Brake and clutch pedal pad
p/n: 70-3148-22
Pad, brake and clutch pedal. For vehicles with manual transmission.
Rigid Run Channel
p/n: 70-0347-58
Stainless beaded edge, mohair-lined, exact replacement for rear side of division bar. Available in 15" pairs.
Beltline Weatherstrip
p/n: 70-0555-58
Weatherstrip, door window inner and outer, front and rear doors. Bend to fit. Available in a 3ft pair.
Vent division bar weatherstrip
p/n: 50-0518-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Front Coil Spring Pad
p/n: 50-0476-35
Pad, front coil spring insulator, upper. Two (2) per car, five and one eighths (5-1/8) inch outside diameter. Height: .28125 inches.
Front stabilizer bushing
p/n: 50-0094-34
Bushings, front stabilizer shaft-to-frame or stabilizer shaft, front or rear. Fully molded rubber. One and one half inch (1 1/2") length by one and one half inch (1 1/2") width by eleven sixteenths inch (11/16") inside hole diameter by one and one half in
Sliding Quarter Window Weatherstrip
p/n: 70-0353-78
Weatherstrip, door window inner and outer, front and rear doors. Bend to fit. Available in a 6ft lengths.
Front suspension bumper
p/n: 50-0092-32
Bumper, front suspension, lower arm. Steel core, with threaded stud, as original. Two (2) per car required.
Side Window Sash Channel
p/n: 70-0641-58
Sash channel, side window glass. U-shaped steel channel only, no filler. Will require that you attach your own window regulator cam to underside as required.
Windshield post to door seal
p/n: 70-0304-73
Weatherstrip, windshield post, upper to door. Seals between front door vent window frame and windshield pillar. Top quality rubber made to original cross-section. Two (2) strips approximately fifteen (15) inches long. May need to trim ends to fit.
Rigid Run Channel
p/n: 70-0516-58
Channel, rigid run, lower side window below beltline, zinc plated steel with black cloth lining. Available in 15" pairs.
Taillight mounting pad
p/n: 50-0100-15
Mounting pad, extrusion, taillight body-to-rear fender. Sold in sets sufficient for two (2) taillights.Length: 55.0 inches. Width: .3125 inches.
Parking brake pedal pad
p/n: 50-0405-22
Pad, parking brake pedal. With "PARK" written on pad. Black only. For pedal pad without "PARK" written on pad see our #50-0348-22.Width: 2.0625 inches.
Door Flipper Stop
p/n: 70-2853-62
This Door Flipper Stop is designed from the original part for superior fitment and seal. The rear flipper stop mounts inside the flipper opening at the very rear of the door flipper.
Door Handle Gasket Set
p/n: 70-1913-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Roof rail filler
p/n: 70-1763-73
Weatherstrip seal, roof rail, outer at quarter window.Length: 1.125 inches. Width: .75 inches.
Headlight Outer Rim Seal
p/n: 27-0063-14
Headlight Outer Rim Seal - Used to seal the headlight beam retainer ring. Replaces # 5945844.
Side Window Vertical Leading Edge Weatherstrip
p/n: 70-0141-58
This Vertical Leading Edge Weatherstrip seal pair is designed from the original part for superior fitment and seal. Slides into metal retaining channel attached to rear side window and seals between the front door window and the rear quarter window.
Firewall grommet
p/n: 70-2067-20
Grommet, main wiring harness through firewall. Excellent reproduction of original.Width: 3.1875 inches. Height: .6875 inches.
Body mounting pad
p/n: 50-0477-48
Pad, body mounting. Fully molded rubber with metal core & locating collar. One and seven eighths inch (1 7/8") outside diameter by one and one eighths inch (1 1/8") locating collar outside diameter by three fourths inch (3/4") locating collar inside diame
Firewall grommet
p/n: 70-2066-24
Grommet, emergency brake cable through firewall. Excellent reproduction of original.Width: 2.5 inches.
Battery clamp cover
p/n: 70-0095-21
Cover, battery clamp. Control unsightly sulfate buildup. Help protect the nearby metal and finish. Good copy from original part.Length: 3.5 inches.