Search Results
Body Mounting Pad Set
p/n: 70-3200-48
This twenty-eight (28) piece Body Mounting Pad set is designed from the original parts for superior fitment and function. Designed from original parts, made from rubber with steel core.
Window Felt and Run Channel Set
p/n: 90-0141-58
This ten (10) piece Window Felt and Run Channel set includes the inner and outer window felts, upper and lower rigid run channels, and flexible run channels needed to complete two (2) doors.
Body Weatherstrip Kit
p/n: 90-3010-90
This kit includes the major weatherstrip components and some other essential parts needed for the body of your restoration project.
Body Weatherstrip Kit
p/n: 90-3009-90
This kit includes the major weatherstrip components and some other essential parts needed for the body of your restoration project.
Front Door Vent Window Set
p/n: 90-0402-90
This front door vent window weatherstrip set is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Front Door Weatherstrip
p/n: 60-0299-72
Door weatherstrip, front door snap-on type. High quality sponge rubber with inserted nylon clips. Each strip approximately one hundred sixty six (166) inches long.
Quarter window weatherstrip
p/n: 70-2519-77
Weatherstrip, fixed rear quarter window. Fully molded with proper cross section rubber extrusion and molded-in corners.
Windshield Gasket
p/n: 60-0266-50
This windshield gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation. It also has the slot to accommodate the outer edge's decorative molding.
Front Door Vent Window Weatherstrips
p/n: 38-0060-55
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Rear wheelhouse seal
p/n: 60-0354-45
Seal, rear wheelhouse panel-to-quarter panel, outer. Two (2) five (5) foot strips, one for each side.Length: 60.0 inches. Width: .21875 inches.
Trunk Weatherstrip - Clipped
p/n: 70-1123-85
This Clipped Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter and directly to the trunk lid using properly spaced plastic clips.
Door Auxiliary Weatherstrip
p/n: 60-0342-73
Weatherstrip, front door, auxiliary on door front at beltline, right and left. Held on by button fasteners (our #50-0198-73, four (4) each included in set). Also known as a "J" seal.
Brake and Clutch Pedal Pads
p/n: 60-0068-22
Brake and Clutch Pedal Pads - The proper design and fully detailed with ribs extending down over sides of the pad. Length: 3.50 inches. Width: 2.0 inches.
Rear Bumper To Body Filler
p/n: 60-0359-30
This dense rubber Rear Bumper To Body Filler is designed from the original part for a superior fitment. The part is approximately sixty-six (66) inches long and fits between the vehicle body and the rear bumper.
Rigid Run Channel
p/n: 70-0347-58
Stainless beaded edge, mohair-lined, exact replacement for rear side of division bar. Available in 15" pairs.
Body Bumper Kit
p/n: 90-0205-90
Body Bumper Kit - hood, door and trunk bumpers. Includes fourteen (14) pieces.
Front Suspension Rubber Bumper
p/n: 60-0219-32
Front Suspension Rubber Bumper for the front suspension lower control arm (attaches to lower arm spring mount). This part is compatible to several Chevrolet model vehicles. Self-retaining, top quality. Height: 1.75 inches.
Flexible Run Channel
p/n: 70-1239-58
Cloth covered, mohair lined flexible metal channel for sides and top of door windows.
Accelerator Pedal Pad
p/n: 60-0239-40
Accelerator Pedal Pad - Slip-over type made from top quality rubber. Length: 8.875 inches.
Beltline Weatherstrip
p/n: 70-0555-58
Weatherstrip, door window inner and outer, front and rear doors. Bend to fit. Available in a 3ft pair.
Trunk Weatherstrip
p/n: 70-1122-85
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid. The seal glues directly to the trunk lid.
Vent division bar weatherstrip
p/n: 60-0529-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Stabilizer Bar End Link Set
p/n: 60-0221-33
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt 3/8"-16 NF x 6-15/16" long. Comes with metal sleeve, metal cup washers and rubber grommets.
Inner Fender Seal
p/n: 60-0288-45
Inner Fender Seal for anti-rattle, running board apron to body, or fender splash panels. Nine sixteenths (9/16) inch by seven eighths (7/8) inch slotted sponge rubber to accept rivets. Sold in eight (8) foot strips.
Flexible Run Channel
p/n: 70-1238-58
Cloth covered, mohair lined flexible metal channel for sides and top of door windows.
Sliding Quarter Window Weatherstrip
p/n: 70-0353-78
Weatherstrip, door window inner and outer, front and rear doors. Bend to fit. Available in a 6ft lengths.
Front Stabilizer Bushing
p/n: 60-0088-34
Front Stabilizer Bushing - Front stabilizer bar mounting. Fully molded rubber. Two (2) required per car. One and five sixteenths inch (1 5/16") length by one and five sixteenths inch (1 5/16") width by five eighths inch (5/8") inside hole diameter by one and three fourths inch (1 3/4") height.
Fenderskirt edge seal
p/n: 60-0201-45
Steele Rubber Products has the best quality Fenderskirt edge seal for your Street Rod or Custom Build project. Made from top-quality rubber to ensure durability and proper seal.
Side Window Sash Channel
p/n: 70-0641-58
Sash channel, side window glass. U-shaped steel channel only, no filler. Will require that you attach your own window regulator cam to underside as required.
Steering column floorplate
p/n: 60-0403-24
Cover, steering gear and clutch pedal push rod dash seal.Length: 8.625 inches. Width: 7.625 inches.
Rigid Run Channel
p/n: 70-0516-58
Channel, rigid run, lower side window below beltline, zinc plated steel with black cloth lining. Available in 15" pairs.
Taillight gasket
p/n: 60-0691-15
Seal, taillight bezel. Correct profile and long lasting material. Two (2) strips cut thirty six (36) inches long.Length: 36.0 inches. Width: .21875 inches.
Exhaust system hanger
p/n: 60-0307-13
Support (insulator) muffler-to-tailpipe, webbing reinforced. One (1) per car.Length: 3.4 inches. Width: 1.0 inches.
Brake master cylinder boot
p/n: 60-0180-24
Boot, brake master cylinder rod. Fits on one and one fourth (1-1/4) inch diameter cylinder. Height: 2.125 inches.
Front Suspension Bumper - Lower Control Arm
p/n: 60-0220-32
Bumper, front suspension, lower arm. Steel core as original, excellent quality.
Body mounting pad
p/n: 60-0188-48
Pad and steel bushing assembly. Two (2) required per vehicle Rectangular rubber with metal core, locating collar and metal bolt. Two and seven sixteenths inch (2 7/16") length by one and three fourths inch (1 3/4") width by three fourths inch (3/4") ins
Hood To Cowl Weatherstrip
p/n: 60-0153-42
This Hood To Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact copy reproduction of the original profile. This weatherstrip installs at the rear of the engine bay to seal between the hood and vehicle body cowl.
Battery clamp cover
p/n: 70-0095-21
Cover, battery clamp. Control unsightly sulfate buildup. Help protect the nearby metal and finish. Good copy from original part.Length: 3.5 inches.
Body mounting pad
p/n: 60-0119-48
Pad, body mounting. Rubber original type with metal core, locating collar and metal bolt liner. Two and one eighths inch (2 1/8") outside diameter by three fourths inch (3/4") inside bolt hole diameter by seven eighths inch (7/8") metal bolt outside diame
Cowl Drain Gutter Hose Grommet
p/n: 33-0329-54
Grommet, cowl gutter drain hose. Nine sixteenth (9/16) inch hole through cowl side wall, five sixteenths (5/16) inch inside diameter. Two (2) per car.
Solenoid plunger boot
p/n: 60-0567-21
Boot, solenoid plunger, starter switch at starter.Height: 1.625 inches.
Window Regulator / Accelerator Rod Seal
p/n: 60-0652-70
This part is used as a front window regulator or accelerator rod through toe board seal. A front window regulator seal for 1955-60 passenger cars with electric windows and for 1957-62 Corvette models. Used as an accelerator rod through toeboard seal for 1955-62 V8 only Corvettes.
Exhaust system hanger
p/n: 60-0308-13
Insulator (support). Muffler/tailpipe system, strap type as original. One and three fourths (1-3/4) inch by three and five eighths (3-5/8) inch.
Hood bumper
p/n: 60-0318-42
Bumper, hood side-to-fender, stem retainer type. Two (2) or more per car, as required.
Splash Apron - A-Arm Dust Shield Set
p/n: 70-4041-45
This two (2) piece Splash Apron - A-Arm Dust Shield set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions.
Gearshift bushing
p/n: 60-0237-24
Bushing, gearshift shaft lever, larger type. Three eighths (3/8) inch inside diameter by nine sixteenths (9/16) inch outside diameter barrel.Height: .
Masticated Rubber Sheet
p/n: 70-0645-45
Masticated sheet. Three thirty seconds (3/32) inch thick rubber sheet containing random milled cotton cord reinforcement for front end splash aprons, etc. This product is a four (4) foot wide roll, and will only be sold in four (4) square foot multiples