This kit includes the major weatherstrip components and some other essential parts needed for the body of your restoration project.
This Front Door Vent Window Set is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
These Front Door Vent Window Weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
This Windshield Gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit.
Hardtop roof rail weatherstrip. This part fits on the roof of the vehicle and seals the side window when the window is fully raised.
Door edge weatherstrip with molded ends. This part is the primary door to body weatherstrip. Includes clips and fasteners for easy installation.
Bumper, rear axle. Revulcanization service only.Height: 3.5 inches.
This Revulcanization Service Only is designed to restore your Front Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Floorplate, steering column. Metal core just like the original.
Support pad, transmission mount (insulator). Revulcanization service only.Length: 5.0 inches. Width: 2.0 inches.
Retainer, torque ball, heavy steel jacket with molded rubber inner collar. Revulcanization service only.
A Rigid Run Channel pair with bright beaded edge, mohair lined channel, die trimmed and round formed at the top. Sold in 29" pairs.
Bumper, rear axle stop. Molded left and right. Revulcanization service only.
Bumper, lower support arm. With metal core and attaching bolt. One (1) pair per car.Width: 2.4375 inches. Height: 4.0 inches.
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. This weatherstrip mounts at the rear of the engine bay to seal between the hood and vehicle body cowl.
Weatherstrip, front door, auxiliary on body above beltline, hinge pillar windshield post. Two (2) strips, each thirteen and three eighths (13-3/8) inches long with retaining clips.
Weatherstrip, front door auxiliary, on door at beltline, right and left. Uses snap-in fasteners, four (4) each included.
Door lock pillar seal. This part seals the bottom of the rear side window, and may also be known as a door jamb seal.
Bumper, grill to front bumper. Fully molded rubber. Three and one fourth inch (3-1/4") outside length. Distance between the two bottom retaining plugs is one and three sixteenths inch (1-3/16'). Biggest plug is one half inch (1/2") diameter, smallest plug
Insulators, rear coil spring. Fabric reinforced rubber as original. One (1) pair per car.
Insulator, engine support at transmission. Revulcanization service only.Length: 7.375 inches. Width: 1.75 inches. Height: 1.5 inches.
Bumper, side window glass in vent frame at top, right and left, brass core.Length: 1.625 inches.
Stainless beaded edge, mohair-lined, exact replacement for rear side of division bar. Available in 15" pairs.
Pad, power brake pedal. Available in BLACK only, "Power Brake" written with white lettering.Width: 5.5 inches. Height: 2.625 inches.
This Beltline Weatherstrip is sold as a three (3) foot pair. The beltline is used for side window inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Front vent window division post seal. Fully molded with metal core and attaching tabs. This part fits opposite the glass run channel and seals the vent window when the vent is closed. See Front door vent weatherstrip for main rubber seal.
Pad, front coil spring insulator, upper. Two (2) per car, five and one eighths (5-1/8) inch outside diameter. Height: .28125 inches.
Bushings, front stabilizer shaft-to-frame or stabilizer shaft, front or rear. Fully molded rubber. One and one half inch (1 1/2") length by one and one half inch (1 1/2") width by eleven sixteenths inch (11/16") inside hole diameter by one and one half in
This Sliding Quarter Window Weatherstrip is used for side window inner and/or outer, front and/or rear doors. Available in a 6ft lengths.
This Peel-N-Stick Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Headlight body mounting gasket. Rubber.
Sash channel, side window glass. U-shaped steel channel only, no filler. Will require that you attach your own window regulator cam to underside as required.
Channel, rigid run, lower side window below beltline, zinc plated steel with black cloth lining. Available in 15" pairs.
Mounting pad, extrusion, taillight body-to-rear fender. Sold in sets sufficient for two (2) taillights.Length: 55.0 inches. Width: .3125 inches.
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Pad, parking brake pedal. With "PARK" written on pad. Black only. For pedal pad without "PARK" written on pad see our #50-0348-22.Width: 2.0625 inches.
Headlight Outer Rim Seal - Used to seal the headlight beam retainer ring. Replaces # 5945844.
This Side Window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. Slides into metal retaining channel attached to rear side window and seals between the front door window and the rear quarter window.
This black rubber Battery Clamp Cover helps to protect the nearby metal and finish. Good copy from an original part. Length: 3-1/2" inches.
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Pad, body mounting. Fully molded rubber with steel core and locating collar. Two inch (2") square by one and one eighth inch (1 1/8") locating collar outside diameter by eleven sixteenths inch (11/16") locating collar inside diameter by one half inch (1/2
Insulator, rear coil spring clamp bolt (upper end). Two (2) per car. Fabric reinforced rubber as original.
Grommet, glove box door cushion. One and three quarters long (1-3/4") and thirteen sixteenths (13/16")wide.Length: 1.75 inches. Width: .8125 inches.
Spring Insulator, rear
Steele Rubber Products offers the best quality Dimmer Switch Grommet for your classic vehicle. This universal fit dimmer switch grommet is used during carpet installations in automotive restorations. Includes a wide flange for floor dimmer switch fitments.
This Masticated Rubber Sheet is three thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
Bushing, strut rod at drive shaft tube. Two (2) per car required.Length: 1.65625 inches.
Pad, several useages. Use as a body mounting pad or as a cushion for body mounting bolt. Fully molded rubber. Up to twenty (20) required per car. Two inches (2") outside diameter by three fourths inch (3/4") inside hole diameter by one half inch (1/2") he
Bushing, rear axle, anti-sway rod ends. Fully molded rubber. Four (4) required per car. One and one fourth inch (1 1/4") top outside diameter by one and one eighth inch (1 1/8") bottom outside diameter by five eighths inch (5/8") inside hole diameter by t
Bumper, hood to fender ledge. Self retaining type. See our # 50-0194-42 for center type.