Search Results
Please click on the part name in red in order to get a complete description.
Glass Weatherstrip Kit
p/n: 90-3028-90
This kit includes the weatherstrip components needed for the glass on your restoration project.
Body Weatherstrip Kit
p/n: 90-3018-90
This kit includes the major weatherstrip components and some other essential parts needed for the body of your restoration project.
Body mounting pad kit
p/n: 70-3200-48
Kit, body mounting. Twenty-eight (28) piece set. Original copy, made from rubber with steel core. Kit includes twelve (12) each of part #60-0119-48, two (2) each of part #60-0188-48, and fourteen (14) each of part #60-0189-48.
Side window run channel kit
p/n: 90-0141-58
This ten (10) piece kit includes the inner and outer windowfelts, upper and lower rigid run channels, and flexible run channels needed to complete two (2) doors. Used for front or rear doors in models with vent windows in the door.
Front Door Vent Window Kit
p/n: 90-0402-90
This front door vent window weatherstrip kit is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Door weatherstrip
p/n: 60-0247-72
Door edge weatherstrip, with pins. This part is the primary door to body weatherstrip. For Cadillac models, these are for the FRONT doors ONLY. For Chevrolet and Pontiac models, these are for the REAR doors ONLY.
Front Door weatherstrip
p/n: 60-0299-72
Door weatherstrip, front door snap-on type. High quality sponge rubber with inserted nylon clips. Each strip approximately one hundred sixty six (166) inches long. Note: For 4 door vehicles see our part #60-0247-72 for the rear door.
Windshield Gasket
p/n: 60-0266-50
This windshield gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation. It also has the slot to accommodate the outer edge's decorative molding.
Front Door Vent Window Weatherstrips
p/n: 38-0060-55
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Rear wheelhouse seal
p/n: 60-0354-45
Seal, rear wheelhouse panel-to-quarter panel, outer. Two (2) five (5) foot strips, one for each side.Length: 60.0 inches. Width: .21875 inches.
Rear Window Gasket
p/n: 70-2051-81
This rear window gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Door Auxiliary Weatherstrip
p/n: 60-0342-73
Weatherstrip, front door, auxiliary on door front at beltline, right and left. Held on by button fasteners (our #50-0198-73, four (4) each included in set). Also known as a "J" seal.
Brake and Clutch Pedal Pads
p/n: 60-0068-22
Brake and Clutch Pedal Pads - The proper design and fully detailed with ribs extending down over sides of the pad. Length: 3.50 inches. Width: 2.0 inches.
Tailgate or Back Door Weatherstrip
p/n: 70-3604-84
This tailgate or back door weatherstrip is designed from the original part for superior fitment and seal. The seal mounts with properly spaced plastic clips around the full perimeter of the rear opening.
Rigid Run Channel
p/n: 70-0347-58
Channel, rigid run, window division bar. Stainless beaded edge, mohair-lined, exact replacement for rear side of division bar.
Front Suspension Rubber Bumper
p/n: 60-0219-32
Front Suspension Rubber Bumper for the front suspension lower control arm (attaches to lower arm spring mount). This part is compatible to several Chevrolet model vehicles. Self-retaining, top quality. Height: 1.75 inches.
Flexible Run Channel 6 Foot
p/n: 70-1239-58
Window run channel with stainless beaded edge. Six (6) foot length. Cloth covered, mohair lined, flexible channel for sides and top of door windows. Exact replacement for listed vehicles but can be used in many applications.
Accelerator Pedal Pad
p/n: 60-0239-40
Accelerator Pedal Pad - Slip-over type made from top quality rubber. Length: 8.875 inches.
Beltline weatherstrip
p/n: 70-0555-58
Weatherstrip, door window inner and outer, front and rear doors. Seven sixteenths (7/16) inch wide, with chrome bead, mohair faced, flexible. Two (2) three (3) foot strips. Bend to fit.
Inner Fender Seal
p/n: 60-0288-45
Inner Fender Seal for anti-rattle, runningboard apron to body, or fender splash panels. Nine sixteenths (9/16) inch by seven eighths (7/8) inch slotted sponge rubber to accept rivets. Sold in eight (8) foot strips.
Vent division bar weatherstrip
p/n: 60-0529-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Flexible Run Channel 5 Foot
p/n: 70-1238-58
Window run channel, stainless beaded edge. Cloth covered, mohair lined flexible metal channel for sides and top of door windows. Perfect dimensions, Five eighths (5/8) inch wide by nine sixteenths (9/16) inch overall height, exact replacement. Five (5) fo
Front Stabilizer Bushing
p/n: 60-0088-34
Front Stabilizer Bushing - Front stabilizer bar mounting. Fully molded rubber. Two (2) required per car. One and five sixteenths inch (1 5/16") length by one and five sixteenths inch (1 5/16") width by five eighths inch (5/8") inside hole diameter by one and three fourths inch (1 3/4") height.
Fenderskirt edge seal
p/n: 60-0201-45
Seal, fenderskirt edge. Proper profile for most skirts of this period, including Fox-Craft. Sixty (60) inch strip.Length: 60. inches. Width: .75 inches.
Steel sash channel
p/n: 70-0641-58
Sash channel, side window glass. U-shaped steel channel only, no filler. Will require that you attach your own window regulator cam to underside as required.
Rigid run channel
p/n: 70-0516-58
Channel, rigid run, lower side window below beltline, zinc plated steel with black cloth lining, one half (1/2) inch deep by one half (1/2) inch wide, fifteen (15) inches long.
Gravel shield anti-squeak
p/n: 60-0213-30
Seal, rear bumper face bar-to-body or gravel shield. Exact profile, three and five eighths (3-5/8) inch wide by fifty nine (59) inches long.
Brake master cylinder boot
p/n: 60-0180-24
Boot, brake master cylinder rod. Fits on one and one fourth (1-1/4) inch diameter cylinder. Height: 2.125 inches.
Front Suspension Bumper - Lower Control Arm
p/n: 60-0220-32
Bumper, front suspension, lower arm. Steel core as original, excellent quality.
Body mounting pad
p/n: 60-0188-48
Pad and steel bushing assembly. Two (2) required per vehicle Rectangular rubber with metal core, locating collar and metal bolt. Two and seven sixteenths inch (2 7/16") length by one and three fourths inch (1 3/4") width by three fourths inch (3/4") ins
Battery clamp cover
p/n: 70-0095-21
Cover, battery clamp. Control unsightly sulfate buildup. Help protect the nearby metal and finish. Good copy from original part.Length: 3.5 inches.
Body mounting pad
p/n: 60-0119-48
Pad, body mounting. Rubber original type with metal core, locating collar and metal bolt liner. Two and one eighths inch (2 1/8") outside diameter by three fourths inch (3/4") inside bolt hole diameter by seven eighths inch (7/8") metal bolt outside diame
Hood to cowl weatherstrip
p/n: 60-0346-42
Anti-squeak, hood-to-cowl. Thirty eight (38) inch strip.Length: 38.0 inches. Width: .5625 inches. Height: .28125 inches.
Taillight Seals
p/n: 70-3766-15
Seals, under taillight assembly. Die cut masticated rubber to authentic original dimensions.
Cowl drain gutter hose grommet
p/n: 33-0329-54
Grommet, cowl gutter drain hose. Nine sixteenth (9/16) inch hole through cowl side wall, five sixteenths (5/16) inch inside diameter. Two (2) per car.
Solenoid plunger boot
p/n: 60-0567-21
Boot, solenoid plunger, starter switch at starter.Height: 1.625 inches.
Window Regulator / Accelerator Rod Seal
p/n: 60-0652-70
This part is used as a front window regulator or accelerator rod through toe board seal. A front window regulator seal for 1955-60 passenger cars with electric windows and for 1957-62 Corvette models. Used as an accelerator rod through toeboard seal for 1955-62 V8 only Corvettes.
Exhaust system hanger
p/n: 60-0308-13
Insulator (support). Muffler/tailpipe system, strap type as original. One and three fourths (1-3/4) inch by three and five eighths (3-5/8) inch.
Hood bumper
p/n: 60-0318-42
Bumper, hood side-to-fender, stem retainer type. Two (2) or more per car, as required.
A-Arm Dust Shields
p/n: 70-4040-45
A-Arm dust shield 2 piece set. Die cut masticated rubber. Includes all factory style holes required for installation.
Gearshift bushing
p/n: 60-0237-24
Bushing, gearshift shaft lever, larger type. Three eighths (3/8) inch inside diameter by nine sixteenths (9/16) inch outside diameter barrel.Height: .
Masticated rubber sheet
p/n: 70-0645-45
Masticated sheet. Three thirty seconds (3/32) inch thick rubber sheet containing random milled cotton cord reinforcement for front end splash aprons, etc. This product is a four (4) foot wide roll, and will only be sold in four (4) square foot multiples
Door handle gasket kit
p/n: 60-0352-69
Gasket set, outside door handle, right and left, front and rear doors. Six (6) piece set for two (2) doors.
Wiring grommet
p/n: 70-0355-14
Grommet, electric wire into light body under fenders, for headlights, taillights, some parking lights and auxiliary (fog) lights. Fits seven eighths (7/8) inch hole in light body. Two (2) to eight (8) per car as required.
Rear spring bushing
p/n: 60-0208-32
Bushing, rear spring, shackle eye and spring eye. Up to twelve (12) per car.CV/GMC TRK 1955-57 Bushing, rubber, rear spring, shackle eye and spring eye.
Hood bumper
p/n: 50-0205-42
Bumper, adjustable type, hood front. Cadmium plated bolt (5/16)-18 x 1-1/4", rubber bumper 1-1/8" in diameter, 5/8" thick.Height: 1.875 inches.
Firewall grommet
p/n: 32-0347-20
Grommet, firewall wiring harness. For wiper control cable, heat tube, etc. Sheet Metal Hole: 1" Center Hole: 1/8" Secondary Holes: 1/16" Outside Diameter: 1-5/16" Slot Width: 1/16"
Window stop stem bumper
p/n: 33-0540-62
Cushion (stem bumper), window stop, lower. For front and rear door, rear side and quarter windows as required.
Body Bolt Cushion
p/n: 60-0189-48
Pad, for each body bolt under frame bracket, to cushion washer and nut. Fully molded rubber. One and seven eighths inch (1 7/8") outside diameter by seven eighths inch (7/8") inside hole diameter by nine sixteenths inch (9/16) height.
Door Weatherstrip w/ Clips (Sponge Rubber Extrusion - General Use)
p/n: 70-1112-73
Door edge weatherstrip made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models.
Side window roller
p/n: 70-0117-62
Anti-rattle roller, side windows. Rubber only, replaces original perfectly and easily. Fits both styles of brackets.
Brown door lock knob
p/n: 70-0660-70
Knob or push button for inside door lock, fits over 1/8" steel rod to door lock. Hard brown rubber, may be lacquered other colors as required.
Shock and stabilizer grommet
p/n: 70-0274-33
Grommet, shock and stabilizer link. Eight (8) required per car. Fully molded rubber with locating collar. One and one sixteenth inch (1 1/16") outside diameter by nine sixteenths inch (9/16") locating collar outside diameter by three eighths inch (3/8") i
Universal mounting pad
p/n: 70-0308-17
Mounting pad, continuous for lights, hinges, brackets, and other bright work when no molded pad is available.
Body hole plug
p/n: 35-0863-45
Plug, body sheet metal holes. Used in various places (like trunks). For one and one half (1-1/2) inch hole in body.
Door drain hole seal
p/n: 60-0442-70
Weatherstrip, door bottom drain hole seal. Also used on tailgate of station wagon. (Two (2) required for this use).Length: 4.0 inches.
Door Weatherstrip w/o Clips (Sponge Rubber Extrusion - General Use)
p/n: 70-1111-73
Door edge weatherstrip made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models.
Shock absorber grommet
p/n: 60-0235-33
Grommet, shock absorber mounting, plain cylinder type with flat ends.
Engine Mount Cushion
p/n: 60-0232-11
Front engine mount large cushion. Four (4) needed per truck. Height: 0.875 inches.
Engine Mount Cushion
p/n: 60-0231-11
Front engine mount small cushion. Four (4) needed per truck. Height: 0.84375 inches.
Antenna hole plug
p/n: 35-0327-45
Plug, antenna mounting for inner front fender at shroud. For vehicles without fender-mounted antenna.
Sash channel filler 1/16 cork
p/n: 70-1115-57
Filler strip, window glass sash channel. One sixteenths (1/16) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherstrip type of filler. This is the highest quality linen back, rubber cork composition on
Firewall retainer
p/n: 60-0586-20
Retainer, firewall insulation panel. "Christmas Tree" style popular during this time. Constructed of vinyl plastic. Up to ten (10) required per car.
Door lock bumper
p/n: 34-0484-71
Bumper, door lock post, upper, one half (1/2) inch diameter by one half (1/2) inch tall, plated screw.Height: .50 inches.
Sash Channel Filler 1/16 Rubber
p/n: 70-2170-57
Filler strip, window glass sash channel. One sixteenths (1/16) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherlip type of filler. This is the highest quality rubber like polymer designed for settin
Door or tailgate bumper
p/n: 33-1228-71
Bumper pads, door or tailgate. Twin retainer style. Three eighths (3/8) inch by seven eighths (7/8) inch by one half (1/2) inch high.
Sash channel filler 1/32 cork
p/n: 70-1114-57
Filler strip, window glass sash channel. One thirty seconds (1/32) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherlip type of filler. This is the highest quality linen back, rubber cork composition
Sash Channel Filler 1/32 Rubber
p/n: 70-2169-57
Filler strip, window glass sash channel. One thirty seconds (1/32) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherlip type of filler.
Firewall grommet
p/n: 32-0162-21
Grommet, utility. Sheet Metal Hole: 3/4" Center Hole: 1/4" Outside Diameter: 15/16" Slot Width: 1/16"
Firewall grommet
p/n: 32-0263-17
Grommet, license light wire through body. Sheet Metal Hole: 3/4" Center Hole: 5/16" Outside Diameter: 1" Slot Width: 1/16"
Door bumper
p/n: 33-1227-71
Bumper, door edge, twin retainer style, three eighths (3/8) inch wide by seven eighths (7/8) inch long by three eighths (3/8) inch high.
Shock absorber bushing
p/n: 70-0547-32
Bushing, shock absorber mounting. Double cone style, rear. Five eighths (5/8) inch hole, one and one sixteenths (1-3/16) inch outside diameter, three fourth (3/4) inch thick.
Trunk floor pan plug
p/n: 35-0070-87
Plug, trunk and floor pan drain hole. Buick 1950-65 Plug, trunk and floor pan drain hole.
Door weatherstrip fastener
p/n: 60-0260-73
Clip, retainer for door edge weatherstrip. Two (2) prong type with oval screw hole, spring steel, cadmium plated.Width: .875 inches. Height: .9375 inches.
Hood bumper
p/n: 70-0294-42
Bumper, hood rest, cap type for adjustable screw, fifteenth sixteenths (15/16) inch, seven sixteenths (7/16) inch thick.
Hood & Door bumper
p/n: 33-0459-42
Bumper, hood to cowl and door hinge pillar upper. May be used in both places.
Standard bumper
p/n: 33-0496-71
Bumper, used at door opening at upper corner, license plate, and/or fuel filler door. Self-retaining type.
Door Bumper
p/n: 33-1234-71
Bumper, door side. One half (1/2) inch block height. Two (2) or four (4) used per car.
Door weatherstrip fastener
p/n: 50-0198-73
Fastener, door edge weatherstrip, steel. One half (1/2) inch long, thirteen thirty second (13/32) inch diameter head, black finish.
