This kit includes the major weatherstrip components and some other essential parts needed for the body of your restoration project.
This Front Door Vent Window Set is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Motor mount. Revulcanization service only. Center holes measure two and seven eighths (2-7/8) inches apart.Length: 5.375 inches.
These Front Door Vent Window Weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
This Windshield Gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit.
This rear window gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Door edge weatherstrip. This part is the primary door to body weatherstrip.
Motor mount, front. Revulcanization service only.Width: 4.875 inches.
Floorplate, steering column. Metal core just like the original.
Bumper, rear axle. Fully molded with new rubber vulcanized to new steel cores. Used on all models with conventional spring suspension.
Support pad, transmission mount (insulator). Revulcanization service only.Length: 5.0 inches. Width: 2.0 inches.
Retainer, torque ball, heavy steel jacket with molded rubber inner collar. Revulcanization service only.
A Rigid Run Channel pair with bright beaded edge, mohair lined channel, die trimmed and round formed at the top. Sold in 29" pairs.
Bumper, rear axle stop. Molded left and right. Revulcanization service only.
Bumper, lower support arm. With metal core and attaching bolt. One (1) pair per car.Width: 2.4375 inches. Height: 4.0 inches.
Door lock pillar seal. This part seals the bottom of the rear side window, and may also be known as a door jamb seal.
Weatherstrip, front door, auxiliary on body above beltline, hinge pillar windshield post. Two (2) strips, each thirteen and three eighths (13-3/8) inches long with retaining clips.
Weatherstrip, front door auxiliary, on door at beltline, right and left. Uses snap-in fasteners, four (4) each included.
Gasket, headlight to fender.Width: 13.0 inches.
Insulators, rear coil spring. Fabric reinforced rubber as original. One (1) pair per car.
Insulator, engine support at transmission. Revulcanization service only.Length: 7.375 inches. Width: 1.75 inches. Height: 1.5 inches.
Bumper, side window glass in vent frame at top, right and left, brass core.Length: 1.625 inches.
Stainless beaded edge, mohair-lined, exact replacement for rear side of division bar. Available in 15" pairs.
Pad, power brake pedal. Available in BLACK only, "Power Brake" written with white lettering.Width: 5.5 inches. Height: 2.625 inches.
This Beltline Weatherstrip Channel is a five (5) foot length of rigid channel with a flocked rubber lip and a flat stainless bead. Can be used as the inner beltline weatherstrip on front doors, rear doors and quarter windows.
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Seal, headlight outer rim to sealed beam retainer ring. Possible fit for models with dual headlights.Width: .375 inches. Height: .9375 inches.
Pad, front coil spring insulator, upper. Two (2) per car, five and one eighths (5-1/8) inch outside diameter. Height: .28125 inches.
Bushings, front stabilizer shaft-to-frame or stabilizer shaft, front or rear. Fully molded rubber. One and one half inch (1 1/2") length by one and one half inch (1 1/2") width by eleven sixteenths inch (11/16") inside hole diameter by one and one half in
Gasket, taillight lens, one fourth (1/4) inch thick sponge rubber.
This Peel-N-Stick Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Sash channel, side window glass. U-shaped steel channel only, no filler. Will require that you attach your own window regulator cam to underside as required.
Gasket, parking light lens and turn signal lens, front.
Channel, rigid run, lower side window below beltline, zinc plated steel with black cloth lining. Available in 15" pairs.
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Pad, parking brake pedal. With "PARK" written on pad. Black only. For pedal pad without "PARK" written on pad see our #50-0348-22.Width: 2.0625 inches.
This Door Flipper Stop is designed from the original part for superior fitment and seal. The rear flipper stop mounts inside the flipper opening at the very rear of the door flipper.
Weatherstrip seal, roof rail, outer at quarter window.Length: 1.125 inches. Width: .75 inches.
This Side Window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. Slides into metal retaining channel attached to rear side window and seals between the front door window and the rear quarter window.
Pad, body mounting. Rubber with metal core, locating collar and metal sleeve as original. Metal sleeve is removable, measures one and one eighth inch (1 1/8") long when removed. Part dimensions with metal sleeve inserted are: One and seven eighths inch (1 7/8")
Cover, battery clamp. Control unsightly sulfate buildup. Help protect the nearby metal and finish. Good copy from original part.Length: 3.5 inches.
Pad, body mounting. Rubber with metal nut and washer molded in. One and seven eighths inch (1 7/8") outside diameter by thirteen sixteenths inch (13/16") nut outside length by seven sixteenths inch (7/16") inside hole diameter. Three fourths inch (3/4") c
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Bumper, hood side on fender ledge center. Self retaining type. See our #50-0095-42 for rear type.Height: 1.625 inches.
Pad, body mounting. Fully molded rubber with steel core and locating collar. Two inch (2") square by one and one eighth inch (1 1/8") locating collar outside diameter by eleven sixteenths inch (11/16") locating collar inside diameter by one half inch (1/2
Insulator, rear coil spring clamp bolt (upper end). Two (2) per car. Fabric reinforced rubber as original.
Grommet, glove box door cushion. One and three quarters long (1-3/4") and thirteen sixteenths (13/16")wide.Length: 1.75 inches. Width: .8125 inches.
Spring Insulator, rear
This Steering Column gasket is designed from the original part for superior fitment and sealing. Gasket is machine cut from quality sponge rubber to authentic original dimensions. This part fits around the steering column to seal the column through the body floor pan.
Grommet, dimmer switch for carpet application.