Search Results
Body Weatherstrip Kit
p/n: 90-3276-90
This kit includes the major weatherstrip components and some other essential parts needed for the body of your restoration project.
Front Door Weatherstrip
p/n: 70-0805-72
Door edge weatherstrip with molded ends. This part is the primary door to body weatherstrip. Includes clips and pins for easy installation.
Front Door Vent Window Set
p/n: 90-0422-90
This front door vent window weatherstrip set is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Rear Door Weatherstrip
p/n: 70-0571-72
Door edge weatherstrip with molded ends, rear doors. This part is the primary door to body weatherstrip. Includes clips and pins for easy installation.
Motor mount service
p/n: 70-1774-11
Motor mount. Revulcanization service only. Center holes measure two and seven eighths (2-7/8) inches apart.Length: 5.375 inches.
Rear door vent weatherstrip
p/n: 38-0088-74
Weatherstrip, rear door vent window. Order our #70-0783-74 division post weatherstrip separately.
Front Door Vent Window Weatherstrips
p/n: 38-0087-55
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Hardtop roof rail weatherstrip
p/n: 70-0534-68
Hardtop roof rail weatherstrip. This part fits on the roof of the vehicle and seals the side window when the window is fully raised.
Windshield Gasket
p/n: 70-0762-50
This Windshield Gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit.
Rear Window Gasket
p/n: 50-0191-81
This rear window gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Motor mount service
p/n: 50-0273-11
Motor mount, front. Revulcanization service only.Width: 4.875 inches.
Steering column floorplate
p/n: 50-0412-36
Floorplate, steering column. Metal core just like the original.
Rear axle suspension bumper
p/n: 70-2638-35
Bumper, rear axle. Fully molded with new rubber vulcanized to new steel cores. Used on all models with conventional spring suspension.
Transmission mount service
p/n: 50-0264-25
Support pad, transmission mount (insulator). Revulcanization service only.Length: 5.0 inches. Width: 2.0 inches.
Torque ball service
p/n: 50-0190-27
Retainer, torque ball, heavy steel jacket with molded rubber inner collar. Revulcanization service only.
Rigid Run Channels
p/n: 70-0536-58
A Rigid Run Channel pair with bright beaded edge, mohair lined channel, die trimmed and round formed at the top. Sold in 29" pairs.
Axle rebound pad
p/n: 50-0370-35
Bumper, rear axle stop. Molded left and right. Revulcanization service only.
Support arm bumper
p/n: 50-0526-32
Bumper, lower support arm. With metal core and attaching bolt. One (1) pair per car.Width: 2.4375 inches. Height: 4.0 inches.
Run channel upper bumper
p/n: 70-1629-62
Bumper, upper division post.Length: 1.5 inches. Width: .5625 inches.
U Jamb lock pillar filler
p/n: 70-1907-79
Rear door lock pillar seal. This part seals the bottom of the rear side window, and may also be known as a door jamb seal. Fully molded authentic rubber construction with metal core. For rear doors.
Door weatherstrip
p/n: 70-0552-73
Weatherstrip, front door, auxiliary on body above beltline, hinge pillar windshield post. Two (2) strips, each thirteen and three eighths (13-3/8) inches long with retaining clips.
Front Door Auxiliary Weatherstrip
p/n: 70-0551-73
Weatherstrip, front door auxiliary, on door at beltline, right and left. Uses snap-in fasteners, four (4) each included.
Rear coil spring pad
p/n: 50-0359-35
Insulators, rear coil spring. Fabric reinforced rubber as original. One (1) pair per car.
Transmission mount service
p/n: 50-0186-25
Insulator, engine support at transmission. Revulcanization service only.Length: 7.375 inches. Width: 1.75 inches. Height: 1.5 inches.
Run Channel Upper Bumper
p/n: 60-0183-62
Bumper, side window glass in vent frame at top, right and left, brass core.Length: 1.625 inches.
Rigid Run Channel
p/n: 70-0347-58
Stainless beaded edge, mohair-lined, exact replacement for rear side of division bar. Available in 15" pairs.
Power brake pedal pad
p/n: 50-0406-22
Pad, power brake pedal. Available in BLACK only, "Power Brake" written with white lettering.Width: 5.5 inches. Height: 2.625 inches.
Beltline Weatherstrip Channel - 5 Foot
p/n: 70-0651-58
A five (5) foot length of rigid channel with a flocked rubber lip and a flat stainless bead. Can be used as the inner beltline weatherstrip on front doors, rear doors and quarter windows.
Vent Window Division Bar Weatherstrip
p/n: 70-0703-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Headlight seal
p/n: 70-1465-14
Seal, headlight outer rim to sealed beam retainer ring. Possible fit for models with dual headlights.Width: .375 inches. Height: .9375 inches.
Front Coil Spring Pad
p/n: 50-0476-35
Pad, front coil spring insulator, upper. Two (2) per car, five and one eighths (5-1/8) inch outside diameter. Height: .28125 inches.
Front stabilizer bushing
p/n: 50-0094-34
Bushings, front stabilizer shaft-to-frame or stabilizer shaft, front or rear. Fully molded rubber. One and one half inch (1 1/2") length by one and one half inch (1 1/2") width by eleven sixteenths inch (11/16") inside hole diameter by one and one half in
Taillight lens gasket
p/n: 50-0197-15
Gasket, taillight lens, one fourth (1/4) inch thick sponge rubber.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0773-WT
This Peel-N-Stick Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Door Handle Gasket Set
p/n: 50-0193-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This four (4) piece gasket set will do two (2) doors.
Side Window Sash Channel
p/n: 70-0641-58
Sash channel, side window glass. U-shaped steel channel only, no filler. Will require that you attach your own window regulator cam to underside as required.
Parking and signal lens gasket
p/n: 50-0192-16
Gasket, parking light lens and turn signal lens, front.
Rigid Run Channel
p/n: 70-0516-58
Channel, rigid run, lower side window below beltline, zinc plated steel with black cloth lining. Available in 15" pairs.
Trunk Weatherstrip
p/n: 70-0773-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Parking brake pedal pad
p/n: 50-0405-22
Pad, parking brake pedal. With "PARK" written on pad. Black only. For pedal pad without "PARK" written on pad see our #50-0348-22.Width: 2.0625 inches.
Body mounting pad
p/n: 50-0506-48
Pad, body mounting. Rubber with metal core, locating collar and metal sleeve as original. Metal sleeve is removable, measures one and one eighth inch (1 1/8") long when removed. Part dimensions with metal sleeve inserted are: One and seven eighths inch (1 7/8")
Battery clamp cover
p/n: 70-0095-21
Cover, battery clamp. Control unsightly sulfate buildup. Help protect the nearby metal and finish. Good copy from original part.Length: 3.5 inches.
Body mounting pad
p/n: 50-0508-48
Pad, body mounting. Rubber with metal nut and washer molded in. One and seven eighths inch (1 7/8") outside diameter by thirteen sixteenths inch (13/16") nut outside length by seven sixteenths inch (7/16") inside hole diameter. Three fourths inch (3/4") c
Door Handle Gasket Set
p/n: 50-0515-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Hood bumper
p/n: 50-0194-42
Bumper, hood side on fender ledge center. Self retaining type. See our #50-0095-42 for rear type.Height: 1.625 inches.
Body mounting pad
p/n: 50-0096-48
Pad, body mounting. Fully molded rubber with steel core and locating collar. Two inch (2") square by one and one eighth inch (1 1/8") locating collar outside diameter by eleven sixteenths inch (11/16") locating collar inside diameter by one half inch (1/2
Rear coil spring pad
p/n: 50-0304-35
Insulator, rear coil spring clamp bolt (upper end). Two (2) per car. Fabric reinforced rubber as original.
Glovebox door check grommet
p/n: 70-0968-88
Grommet, glove box door cushion. One and three quarters long (1-3/4") and thirteen sixteenths (13/16")wide.Length: 1.75 inches. Width: .8125 inches.