Search Results
Body Weatherstrip Kit
p/n: 90-3129-90
This kit includes the major weatherstrip components and some other essential parts needed for the body of your restoration project.
Front door weatherstrip
p/n: 60-0638-72
Door edge weatherstrip, front door. This part is the primary door to body weatherstrip.
Front Door Vent Window Kit
p/n: 90-0411-90
This front door vent window weatherstrip kit is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Window felt weatherstrip
p/n: 80-0696-57
Original equipment style side window horizontal seal (also known as beltline weatherstrip). These strips wipe the side windows when the glass is lowered. They come ready to install with finished ends and body curvature bends for a factory like appearance
Rear door weatherstrip
p/n: 60-0639-72
Door edge weatherstrip, rear door. This part is the primary door to body weatherstrip.
Rear Window Gasket
p/n: 60-0388-81
This rear window gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Windshield Gasket
p/n: 60-0386-50
This windshield gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation. It also has the slot to accommodate the outer edge's decorative molding.
Front Door Vent Window Weatherstrips
p/n: 38-0072-55
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Engine Mounts - S/B Chevrolet
p/n: 70-1633-11
Engine Mounts, front pair. Three (3) bolt S/B Chevrolet. New replacement part manufactured to meet or exceed factory specifications.
Door weatherstrip
p/n: 70-0551-73
Weatherstrip, front door auxiliary, on door at beltline, right and left. Uses snap-in fasteners, four (4) each included.
Front Stabilizer Kit
p/n: 60-0217-34
Link kit, full replacement, front stabilizer bar link. Twenty-two (22) piece set completely replaces links at both ends of stabilizer bar. Hex head bolt 5/16"-24nf x 7-3/4" long. Comes with metal sleeve, metal cup washers and rubber grommets.
Gravel shield anti-squeak
p/n: 60-0359-30
Seal, rear bumper-to-body. Fully molded rubber. Approximately sixty-six (66) inches long. Extrusion ends measure two and one fourths inch (2-1/4") wide by three eighths inch (3/8") height.
Rigid Run Channel
p/n: 70-0347-58
Stainless beaded edge, mohair-lined, exact replacement for rear side of division bar. Available in 15" pairs.
Window Sash / Beltline Channel
p/n: 70-0651-58
Rigid, rubber covered weatherstrip with flock lining and one fourth (1/4) inch chrome edge. Available in a 6ft piece.
Transmission Mount
p/n: 70-2058-25
Transmission mount, rear. One (1) required per vehicle. Aftermarket replacement type.
Inner Fender Seal
p/n: 60-0288-45
Inner Fender Seal for anti-rattle, runningboard apron to body, or fender splash panels. Nine sixteenths (9/16) inch by seven eighths (7/8) inch slotted sponge rubber to accept rivets. Sold in eight (8) foot strips.
Headlight seal
p/n: 70-1465-14
Seal, headlight outer rim to sealed beam retainer ring. Possible fit for models with dual headlights.Width: .375 inches. Height: .9375 inches.
Vent division bar weatherstrip
p/n: 60-0534-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0773-WT
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.
Flexible Run Channel
Cloth covered, mohair lined flexible metal channel for sides and top of door windows. Available in 5ft and 6ft lengths.
Fenderskirt edge seal
p/n: 60-0201-45
Steele Rubber Products has the best quality Fenderskirt edge seal for your Street Rod or Custom Build project. Made from top-quality rubber to ensure durability and proper seal.
Steel sash channel
p/n: 70-0641-58
Sash channel, side window glass. U-shaped steel channel only, no filler. Will require that you attach your own window regulator cam to underside as required.
Body mounting pad
p/n: 60-0383-48
Cushion assembly body mounting pad. Fully molded rubber with metal core, locating collar and metal bolt sleeve. Rectangular. Three inches (3") length by two inches (2") width. Seven sixteenths inch (7/16") inside hole diameter by five eighths inch (5/8")
Trunk Weatherstrip
p/n: 70-0773-84
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Rigid Run Channel
p/n: 70-0516-58
Channel, rigid run, lower side window below beltline, zinc plated steel with black cloth lining. Available in 15" pairs.
Transmission mount service
p/n: 60-0465-25
Transmission mount. One (1) per car. Revulcanization service only.Length: 5.75 inches.
Hood to radiator weatherstrip
p/n: 60-0670-42
Weatherstrip or seal, hood panel to radiator support. Correct extruded rubber strip. Used on vehicles with factory A/C.
Brake master cylinder boot
p/n: 60-0180-24
Boot, brake master cylinder rod. Fits on one and one fourth (1-1/4) inch diameter cylinder. Height: 2.125 inches.
Taillight gasket
p/n: 60-0692-15
Seal, taillight bezel. Correct profile and long lasting material. Two (2) strips cut twenty four and three fourths (24-3/4) inches long.Length: 24.
Hood to cowl weatherstrip
p/n: 60-0417-42
Seal (anti-squeak). Hood to cowl. One forty three (43) inch strip, as required for one (1) car.Length: 43.0 inches. Width: .6875 inches. Height: .
Body mounting pad
p/n: 60-0382-48
Cushion assembly (body mounting pad). Rubber with metal core, locating collar and metal bolt as original. Metal bolt is removable, measures fifteen sixteenths inch (15/16") long when removed. Part dimensions with metal bolt inserted are: Two and one eight
Battery clamp cover
p/n: 70-0095-21
Cover, battery clamp. Control unsightly sulfate buildup. Help protect the nearby metal and finish. Good copy from original part.Length: 3.5 inches.
Splash Apron / A-Arm Dust Shield
p/n: 70-2800-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Cowl Drain Gutter Hose Grommet
p/n: 33-0329-54
Grommet, cowl gutter drain hose. Nine sixteenth (9/16) inch hole through cowl side wall, five sixteenths (5/16) inch inside diameter. Two (2) per car.
Window Stop Stem Bumper
p/n: 33-0675-62
Cushion (stem bumper), window stop, lower. For front and rear door, rear side and quarter windows as required.
Hood bumper
p/n: 70-2127-42
Bumper, hood side ledge. Correct, fully molded original factory design made of soft rubber. One (1) pair per car.Width: 1.0 inches. Height: .50 inches.
Solenoid plunger boot
p/n: 60-0567-21
Boot, solenoid plunger, starter switch at starter.Height: 1.625 inches.
Front Fender Splash Panel Seals
p/n: 70-3765-45
This two (2) piece Front Fender Splash Panel Seal pair is designed from the original part for superior fitment and seal. Panel pieces are die cut from quality masticated rubber to authentic original dimensions.
Window Regulator / Accelerator Rod Seal
p/n: 60-0652-70
This part is used as a front window regulator or accelerator rod through toe board seal. A front window regulator seal for 1955-60 passenger cars with electric windows and for 1957-62 Corvette models. Used as an accelerator rod through toeboard seal for 1955-62 V8 only Corvettes.
Glovebox door check grommet
p/n: 70-0968-88
Grommet, glove box door cushion. One and three quarters long (1-3/4") and thirteen sixteenths (13/16")wide.Length: 1.75 inches. Width: .8125 inches.
Exhaust system hanger
p/n: 60-0308-13
Insulator (support). Muffler/tailpipe system, strap type as original. One and three fourths (1-3/4) inch by three and five eighths (3-5/8) inch.
Door handle gasket kit
p/n: 60-0541-69
Gasket set, door handle, six (6) piece set. One thirty seconds (1/32) inch thick.
Gearshift bushing
p/n: 60-0237-24
Bushing, gearshift shaft lever, larger type. Three eighths (3/8) inch inside diameter by nine sixteenths (9/16) inch outside diameter barrel.Height: .
Masticated rubber sheet
p/n: 70-0645-45
Masticated sheet. Three thirty seconds (3/32) inch thick rubber sheet containing random milled cotton cord reinforcement for front end splash aprons, etc. This product is a four (4) foot wide roll, and will only be sold in four (4) square foot multiples
Body mounting pad
p/n: 40-0324-48
Cushion, used as either a body mounting pad or for all body bolt nuts, below brackets. Fully molded rubber. Two inch (2") outside diameter by one half inch (1/2") inside hole diameter by three eighths inch (3/8") height.
Hood bumper
p/n: 50-0205-42
Bumper, adjustable type, hood front. Cadmium plated bolt (5/16)-18 x 1-1/4", rubber bumper 1-1/8" in diameter, 5/8" thick.Height: 1.875 inches.
Window Stop Stem Bumper
p/n: 33-0540-62
Cushion (stem bumper), window stop, lower. For front and rear door, rear side and quarter windows as required.