Instrument Panel Grommet
p/n: 70-1654-88
Grommet, instrument panel to windshield frame. Two (2) to six (6) required.Length: 1.3125 inches. Width: 1.0625 inches.
License Plate Light Gasket
p/n: 70-3334-17
This License Plate Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the License Plate Light Lens and the License Plate Light Housing or Bezel.
Lock Cylinder Gasket
p/n: 60-0641-69
This Lock Cylinder Gasket is die cut from one-thirty-second (1/32) inch neoprene.
Lower suspension arm dust seal
p/n: 70-0646-32
Seal, lower suspension arm, inner. Four (4) piece set.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
Metal Sleeved Grommet
p/n: 70-0203-41
Flanged rubber grommet with metal sleeve bushing. Used as part of the accelerator relay lever. Also used from 1959-61 on all Cadillac models as a bushing for the windshield wiper relay lever adaptor.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0773-WT
This Peel-N-Stick Trunk Weatherstrip is designed from the original part for superior fitment and seal. The weatherstrip mounts around the full perimeter of the trunk directly to the body.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0510-WT
This Peel-N-Stick Trunk Weatherstrip is made from a high-quality EPDM sponge rubber. Available by the foot.
Prop shaft support service
p/n: 70-0748-27
Bearing support bracket assembly, drive shaft center bearing. Revulcanization service only. .
Rear Door Hinge Pillar Fillers
p/n: 60-0591-79
This Rear Door Hinge Pillar Filler pair seals the bottom of the rear door side window and may also be known as a rear door jamb seal. Fully molded authentic rubber construction with metal core.
Rear Door Weatherstrips
p/n: 60-0592-72
This Rear Door Weatherstrip pair is designed from the original part for superior fitment and seal. These weatherstrips mount around the front, bottom, and rear of the rear doors using pre-installed clips.
Rear Grill to Body Seal
p/n: 70-3124-31
This Rear Grill to Body Seal is designed from the original part for superior fitment and seal. This seal mounts on the top edge of REAR grill above the rear bumper.
Rear View Mirror Mounting Pad
p/n: 70-3082-70
This single Rear View Mirror Mounting Pad To Door gasket is designed from the original part for superior fitment and seal. The gasket is precision die cut to the original specifications. This gasket is for one (1) door mounted rear view mirror.
Rear Window Gasket
p/n: 60-0553-81
This Rear Window Gasket mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
Rigid Run Channels
p/n: 70-0516-58
This Rigid Run Channel pair is zinc plated steel with black cloth inside lining to provide a smooth sliding surface for glass movement. Also works to protect the glass. Fastens in place by small screws or rivets on top and bottom.
Rigid Run Channels
p/n: 70-0347-58
This Rigid Run Channel pair is stainless beaded and mohair-lined to help eliminate window rattles and provide a smooth sliding surface for glass movement. Also works to protect the glass.
Rigid Run Channels
p/n: 70-0536-58
A Rigid Run Channel pair with bright beaded edge, mohair lined channel, die trimmed and round formed at the top. Sold in 29" pairs.
Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.