This four (4) piece front Front Door Vent Window Weatherstrip contains the main vent window seals and division post seals. The division post seals contain a metal core for durability and easy installation.
Door edge weatherstrip. Includes both front and rear door seals. These parts are the primary door to body weatherstrips. Contains plastic pins and metal tabs that are attached to the door weatherstrips. Also includes four (4) screws.
This is a Original equipment style side window horizontal weatherstrip set (also known as beltline weatherstrip). This eight (8) piece anti-rattle set includes inner and outer window felt beltline weatherstrips for each door and quarter window.
This Rear Window Gasket mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
This Windshield Gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative chrome molding.
This Leaf Spring Shackle Set is manufactured to OEM specifications to install for an authentic fit and finish. Rear of rear spring shackle bars and bolt assembly with rubber bushings. Two (2) sets required per car.
These rear door stationary window weatherstrips are fully molded for superior performance and designed from originals for a factory fit.
This Front Coil Spring Saddle Insulator Set is a four (4) piece kit with two front coil spring bushings and two spring insulators to restore the ride quality performance of your classic vehicle.
This Rear Bumper To Body Stone Deflector is designed from the original part for a superior fitment level. This filler piece seals between the rear bumper and the body.
Seal, accelerator pedal rod.
This collared Steering Column Floor Seal is designed from the original part for superior fitment and sealing. This gasket is manufactured from top quality EPDM rubber to authentic original dimensions. This part fits around the steering column to seal the column through the body floor pan.
This automatic Transmission Mount is designed from the original part for superior fitment and seal. This rear mount fits between the transmission and the crossmember to locate and retain the rear of the engine / transmission powertrain.
Shield, generator splash.
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
This Front Fender To Cowl Seal pair is designed from the original part for superior fitment and seal. These filler strips fit at the rear of the front fender to the cowl side panels.
Pad, horn ring pressure.
Bumpers, door. Installed on rear of door just above lock.
Bumper, front suspension.
This Firewall To Hood Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This single piece cowl lacing seal mounts at the rear of the engine bay to seal between the hood and vehicle body cowl / firewall.
Bumpers, hood front to radiator support. Five sixteenths (5/16) inch by twenty four (24) thread.
Insulator, gear shift.
Gaskets, air vent inlet duct to cowl.
This eleven (11) piece Stabilizer Bar End Link Repair Set is designed to withstand harsh conditions without deteriorating. Two (2) end link sets required per car.
This Parking Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Parking Light Lens and the Parking Light Housing or Bezel.
Pad, brake and clutch pedal. Slip over type.
Bumpers, door. Seven sixteenths (7/16) inch high. Fits on door jamb where rear of door closes against body and on rear lower part of door.
Bumpers, door. Five eighths (5/8) inch high. Installs on door jamb where rear of door closes against body and on rear lower part of door.
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This four (4) piece gasket set will do either front two (2) or rear two (2) doors.
Bumpers, fender to hood. Used in top of fender. Four (4) piece set.
Gaskets, taillight lens.
Bumpers, fuel tank door.
Bumpers, trunk lid.
Pad, deck lid lock cylinder sleeve.
Grommet, antenna lead-in. For front mount type.
Bumpers, glovebox and/or fuel filler door. Used as glove box door bumpers for all models listed, used as fuel door bumper for 1950-51 cars and 57-59 retractables only.
Plug, cowl and floor pan. This body plug covers a sheet metal hole that is one and one seven eighths (1-7/8) inch in diameter.
This lower door glass bumper is designed from the original part for superior fitment. If your door window goes too low, or makes a metallic sound when lowered all the way down, you likely need to replace this lower door glass bumper.
Stop, glovebox arm.Ford Truck 1957-64 Stop, glovebox arm. Requires 2 each. Ford Cars 1955-68 Bumper, glovebox door check arm stop.
Plug, cowl and floor pan. This body plug covers a sheet metal hole that is one and one fourth (1-1/4) inch in diameter.
Plug, hole in dog leg cover. Installs at front of door where bolt to adjust vent window frame is located. This body plug covers a sheet metal hole that is one and one half (1-1/2) inch in diameter.
Plug, cowl and floor pan. Three fourths (3/4) inch.
Plug, brake adjustment hole. Fits five sixteenths (5/16) inch by one (1) inch slot. Most models with drum brakes.Length: 1.25 inches. Height: .875 inches.