Please click on the part name in red in order to get a complete description.
This front door vent window weatherstrip kit is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Door edge weatherstrip. This part is the primary door to body weatherstrip.
This rear window gasket mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
This windshield gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
Original equipment style side window horizontal seal kit (also known as beltline weatherstrip). Eight (8) piece kit includes inner and outer felt beltline weatherstrip for each door and quarter windows. These strips wipe the side windows when the glass is
Seal, rear bumper to body. Splash apron. Three (3) piece kit includes: left, right and special molded center piece.
Front Coil Spring Saddle Insulator Kit - Two front coil spring bushings and two spring insulators to restore the performance of your classic vehicle. Requires two (2) per car.
Insulator, cantilever spring type rear support.
Pad, transmission support cross member mount.
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid.
Shackle kit, rear of rear spring. Two (2) kits required per car.
Shield, generator splash.
Bumpers, side of hood to fender. Four (4) piece set.
Seals, windshield drain trough. For A-pillar
Kit, cowl lacing. Clips installed.
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Seal, steering tube to floor. Used on top of floor mat.
Pads, taillight housing to body.
Bumpers, hood front to radiator support. Five sixteenths (5/16) inch by twenty four (24) thread.
Seal, radiator support to hood. Includes staples to install.1960-62: All Falcon models; 1963: Falcon 6 cylinder models EXCEPT those with air conditioner.
Insulator, gear shift.
Lacing, hood cowl.
Gaskets, parking light lens.
This eleven (11) piece Front Stabilizer Bar End Link Kit is designed from original parts so it fits correctly. Two (2) kits / sets required per car as one (1) kit / set services one side of front stabilizer bar.
Pads, outside door handle.
Pad, brake and clutch pedal. Slip over type.
Bumpers, door. Five eighths (5/8) inch high. Installs on door jamb where rear of door closes against body and on rear lower part of door.
Bumpers, door. Seven sixteenths (7/16) inch high. Fits on door jamb where rear of door closes against body and on rear lower part of door.
Bumper, front suspension. Bumper section is 1-3/4" tall, 1-1/2" long, and 1-1/8 wide.
Upper Control Arm Bumper made with top quality rubber. Includes nut.
Insulators, gear shift lever arm.
Gasket, headlight bucket to fender.
Grommet, antenna lead-in. For front mount type.
Gaskets, wiper pivot bezel to cowl.
Bumpers, glovebox and/or fuel filler door. Used as glove box door bumpers for all models listed, used as fuel door bumper for 1950-51 cars and 57-59 retractables only.
Plug, cowl and floor pan. This body plug covers a sheet metal hole that is one and one seven eighths (1-7/8) inch in diameter.
Seal, accelerator pedal linkage to firewall.
Bumper, brake and clutch pedal arm.
Bumpers, ashtray door or glove box door.
Stop, glovebox arm.Ford Truck 1957-64 Stop, glovebox arm. Requires 2 each. Ford Cars 1955-68 Bumper, glovebox door check arm stop.
Plug, cowl and floor pan. This body plug covers a sheet metal hole that is one and one fourth (1-1/4) inch in diameter.
Plug, hole in dog leg cover. Installs at front of door where bolt to adjust vent window frame is located. This body plug covers a sheet metal hole that is one and one half (1-1/2) inch in diameter.
Plug, cowl and floor pan. Three fourths (3/4) inch.
Bumper, fuel tank filler lid. Gray rubber.Ford Cars 1960-63 Bumper, license plate rubber. Used on rear bumper. 2 required per car.
Plug, brake adjustment hole. Fits five sixteenths (5/16) inch by one (1) inch slot. Most models with drum brakes.Length: 1.25 inches. Height: .875 inches.
Tip, sun visor arm boot. Used where sun visor hooks to clip in center. Two (2) required per car.