Vent Window Pivot Post Rivet
p/n: 70-4757-98
This Vent Window Pivot Post Rivet is used to replace the hinge pivot rivet for both left and right vent window assemblies. Commonly used for General Motors car and truck models.
License Plate Light or Heater Motor Wire Grommet
p/n: 20-1815-20
This License Plate Light or Heater Motor Wire Grommet is designed from the original part for superior fitment and function. This part functions as a License Plate Light Grommet(s) for Bronco and as a Heater Motor Wire Grommet for 1957-1958 Ford Car models.
5/16" Glovebox Door Bumper
p/n: 33-0128-88
This 5/16" Glovebox Door Bumper is designed from the original part for superior fitment, finish and function. This bumper is commonly used as a glovebox door bumper on GM models.
5/16" Standard Stem Bumper - GM
p/n: 33-0127-41
This 5/16" Standard Stem Bumper is designed from the original part for superior fitment, finish and function. This bumper is commonly used as a console and fuel filler door bumper on GM models.
Hood Bumper
p/n: 20-2753-42
This Hood Bumper is a quality reproduction of the original factory part. The bumper attaches to the front fenders to support/cushion the hood closure. Used to provide a cushion for the hood closure that also minimizes vibration.
15/16" Trunk Bumper
p/n: 33-0350-87
This 7/8" Trunk Bumper is a quality reproduction of the original factory part. Bumper fits to the rear compartment lid, lower corners on lid. Two (2) per car. Manufactured to OEM specifications to install for an authentic fit, finish, and function.
Hood to Fender Bumper
p/n: 70-3305-42
This Hood to Fender Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure. Four (4) required per car.
Rear License Plate Bracket Bumper
p/n: 70-4478-45
This Rear License Plate Bracket Bumper is designed from the original part for superior fitment and function. This OEM exact copy reproduction bumper mounts in the spring retainer on the license plate bracket.
Bumper support bar pad
p/n: 20-2765-45
Pads, front bumper bracket to fender. Two (2) required per car.
Glovebox and License Plate Bumper
p/n: 20-2889-45
Bumpers, glovebox and/or license plate. Used as glove box door bumpers for 65-66 and 71-73 models, used as license plate bumper for 65-70 models.
Lock Cylinder Gasket
p/n: 60-0641-69
This Lock Cylinder Gasket is die cut from one-thirty-second (1/32) inch neoprene.
Hood Bumper
p/n: 33-0861-42
This Hood Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
Door Weatherstrip Fastener
p/n: 50-0198-73
This Door Weatherstrip Fastener is steel with a black finish. Each push-in fastener measures one half (1/2") inch long with a thirteen thirty second (13/32") inch diameter head. Reproduction fastener is designed from the original part to fit correctly.
Brake Adjustment Hole Cover Plug
p/n: 70-1092-24
A quality molded rubber Brake Adjustment Hole Cover Plug that inserts into brake adjustment hole in the backing plate. Most models with drum brakes. Length: 1.25 inches. Height: .875 inches.
7/8" Trunk Bumper
p/n: 33-0293-87
This 7/8" Trunk Bumper is a quality reproduction of the original factory part. Self-retaining bumper is manufactured to OEM specifications to install for an authentic fit, finish, and function.
Sun Visor Tips
p/n: 20-2882-88
These Sun Visor Tips are reproductions manufactured to OEM specifications to install for an authentic fit, finish and function. Sold as a pair.
3/4" Body Hole Plug
p/n: 20-1038-21
This Body Hole Plug is designed from the original part for superior fitment, finish and function. This plug is made from high quality EPDM dense rubber to provide excellent durability. This body plug covers a sheet metal hole that is three-fourths (3/4") inches in diameter.
Fuel Filler Door Bumper
p/n: 33-0538-41
This Fuel Filler Door Bumper is a quality reproduction of the original factory part. This rubber bumper attaches to the Fuel Filler Door to support / cushion the closure and prevent metal to metal contact. Usually requires two (2) bumpers each per vehicle.
Hydraulic Pump Mounting Pad
p/n: 70-0946-67
This Hydraulic Pump Mounting Pad is designed from the original part for superior fitment and function. For folding top hydraulic pump mount. Special design to hold pump mounting bracket to floor pan. Four (4) pads needed per car. Height: 1" inch.
Hood To Fender Bumper
p/n: 70-1836-42
This Hood To Fender Bumper is designed from the original part for superior fitment, finish and function. This bumper is manufactured with quality EPDM dense rubber and measures 1-7/16" x 11/16" inches.
Door Bumper - Lower
p/n: 70-3308-71
This Lower Door Bumper is designed from the original part for superior fitment and function. Bumper pushes into slot on door at bottom.
3/4" Trunk Floor Pan Plug
p/n: 35-0070-87
This Trunk Floor Pan Plug is fully molded and designed from the original part for superior fitment and seal. This plug is made from high-quality EPDM dense rubber to provide excellent durability.
Body Hole Plug
p/n: 20-1040-21
This Body Hole Plug is designed from the original part for superior fitment, finish and function. This plug is made from high quality EPDM dense rubber to provide excellent durability. This body plug covers a sheet metal hole that is one and one half (1-1/2") inch in diameter.
Window Regulator Arm Roller
p/n: 70-4813-62
This Window Regulator Arm Roller is designed from the original part for superior fitment and function. This nylon roller fits to the window regulator arm to lower and raise the side windows.
1-1/4" Body Hole Plug
p/n: 20-1039-21
This Body Hole Plug is designed from the original part for superior fitment, finish and function. This plug is made from high quality EPDM dense rubber to provide excellent durability. This body plug covers a sheet metal hole that is one and one fourth (1-1/4") inches in diameter.
Glovebox Arm Bumper Stop
p/n: 20-1399-88
Stop, glovebox arm.Ford Truck 1957-64 Stop, glovebox arm. Requires 2 each. Ford Cars 1955-68 Bumper, glovebox door check arm stop.
1" Floor Pan Plug
p/n: 35-0262-20
This Floor Pan Plug is fully molded and designed from the original part for superior fitment and seal. This plug is made from high-quality EPDM dense rubber to provide excellent durability. Up to twelve (12) used per vehicle.
Engine light grommet
p/n: 60-0706-17
Grommet, engine compartment light wire in lid. Not a universal grommet, this part is dimensionally just like the original.
Door Bumper
p/n: 70-2045-71
This Door to Body Bumper is quality reproduction of the original factory part. Use varies depending upon model and body type. Some models uses four (4) bumpers for front doors and four (4) for rear doors.
1/4" Universal Mounting Pad
p/n: 70-0308-17
This Universal Mounting Pad is used for lights, hinges, brackets, and other bright work when no molded pad is available. Manufactured with special edge lip to hug bright work when clamped down. Shape outline to suit.
Body Hole Plug
p/n: 20-0843-20
Plug, style-side bed side panel. One and five eighths (1-5/8) inch diameter. Fits 1-1/16" hole.
Door Bumper, Upper / Lower
p/n: 20-2825-71
This Door Bumper is a quality reproduction of the original factory part. Upper / Lower push-in type. Four (4) required per car.
Body Hole Plug
p/n: 20-0844-20
Plug, cowl side panel inner. One and seven eighths (1-7/8) inch diameter. Two (2) each required per truck.
Door Bumper
p/n: 20-0067-71
This Door Bumper is designed from the original part for an authentic fit, finish and function. Installs on back edge of door. Usually two (2) to eight (8) per vehicle.
Body Hole Plug
p/n: 20-0845-20
Plug, oval floor pan front. Rubber. One half (1/2) inch by one (1) inch diameter. Two (2) each required per truck.
Door Bumper
p/n: 33-1227-71
This Door Bumper is fully molded and designed from the original part for superior fitment. The twin retainer style rubber bumper attaches to the vehicle body to support/cushion the door closure. Usually requires two (2) bumpers each per vehicle.
Door Bumper
p/n: 70-1563-71
Bumper, door edge.Length: 1.0 inches. Width: .625 inches. Height: .75 inches.
1/16" Filler and Cushion Strip
p/n: 70-1236-48
Filler and cushion strip with a variety of applications. Available by the foot.
Door Glass Bumper
p/n: 20-1172-71
This lower door glass bumper is designed from the original part for superior fitment. If your door window goes too low, or makes a metallic sound when lowered all the way down, you likely need to replace this lower door glass bumper.
Tailgate Side Seals
p/n: 70-4009-85
This Tailgate Side Seals includes right and left side with installation screws. These seals are properly molded from originals for a factory like fit.
Hood To Cowl Weatherstrip Bumper
p/n: 70-1251-42
This Hood To Cowl Weatherstrip Bumper is a quality reproduction of the original factory part. One fourth (1/4") of an inch high.
Door or Tailgate Bumper
p/n: 33-1228-71
This Door Bumper is fully molded and designed from the original part for superior fitment. This rubber bumper attaches to the vehicle body to support / cushion the door closure. Usually requires two (2) bumpers each per vehicle.
Hood To Cowl Weatherstrip Bumper
p/n: 70-1252-42
This Hood To Cowl Weatherstrip Bumper is a quality reproduction of the original factory part. Five sixteenths (5/16") of an inch high.
Accelerator Pedal Rod Seal
p/n: 20-2745-41
This Accelerator Pedal Rod Seal is used when running the accelerator rod through the firewall. The seal helps to block out air and wind noise from entering into the cabin.
Hood To Cowl Weatherstrip Bumper
p/n: 70-1250-42
This Hood To Cowl Weatherstrip Bumper is a quality reproduction of the original factory part. Three sixteenths (3/16") of an inch high.
PCV valve grommet
p/n: 20-2696-20
Grommet, valve cover (Positive crankcase ventilation valve). Used in round hole on steel valve covers.
AC Condenser Tube to Radiator Support Grommet
p/n: 20-2723-31
This A/C Condenser Tube to Radiator Support Grommet is used to protect the air conditioner condenser tubes to the radiator support. Made from flat foam rubber to provide protection.
Door Bumper
p/n: 33-0981-71
This Door Bumper is designed from the original part for superior fitment, finish and function. Molded with push in carrot retainers, this bumper is commonly used as a upper door bumper on GM models.
Standard Bumper
p/n: 20-0001-88
This Standard Bumper pair is designed from the original part for superior fitment and function. This rubber bumper fits ashtray or glovebox doors.
Cowl Top Plug
p/n: 20-1813-20
This Cowl Top Plug is designed from the original part for an authentic fit, finish, and appearance. This plug installs in the access hole in cowl top.
Clutch or Brake Pedal Bumper
p/n: 20-1051-24
This Clutch or Brake Pedal Bumper is designed from the original part for superior fitment, finish and function. This bumper is commonly used as a clutch or brake pedal arm stop cushion.
Parking Brake Cable To Floor Seal
p/n: 20-0853-24
This Parking Brake Cable To Floor Seal is designed from the original part for superior fitment and seal. This works to seal the parking brake cable as it passes through the truck floor pan.
1" Floor Pan Grommet
p/n: 35-0515-20
This Floor Pan Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability.
Tailgate Bumper
p/n: 20-0888-45
These Tailgate Bumpers are designed from original parts for a correct fit. Sold as a pair.
Body Hole Plug
p/n: 20-1041-21
Plug, cowl and floor pan. This body plug covers a sheet metal hole that is one and one seven eighths (1-7/8) inch in diameter.
Tailgate Latch Striker Bumper
p/n: 70-1911-87
This Tailgate Latch Striker Bumper is a quality reproduction of the original factory part. This rubber bumper attaches to the station wagon tailgate to cushion its closure. Usually requires two (2) bumpers each per vehicle.
2" Firewall Grommet
p/n: 60-0707-20
This Firewall Grommet is used to run the body wiring harness at the engine bulkhead through the firewall. Special design for this usage.
Brake Pedal Pad
p/n: 20-1043-22
This reproduction Brake Pedal Pad slips over the full perimeter of the brake pedal for a precise, factory fit. Replaces original brake pedal pad for models with manual transmission and manual drum (not disc) brakes.
5/16” Round Top Hood Bumper
p/n: 20-2755-42
This Hood Bumper pair is a quality reproduction of the original factory part. This rubber bumper attaches to the front radiator support to cushion / bump stop the hood closure.
5/8" Door Weatherstrip without Clips
p/n: 70-1111-73
This Door Weatherstrip made from high-quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
Fuel filler cover bumper
p/n: 20-0006-41
Bumpers, fuel tank door. Single stem and double retainer bumper set.
Bumper Cap - Door, Hood and Trunk
p/n: 82-0020-42
This Bumper Cap is a quality reproduction of the original factory part. Serves as a Door, Hood and Trunk Bumper Cap for adjustment bolt. 7/8" diameter X 7/16" thick. Each
Tailgate Bumper
p/n: 70-1609-87
This Tailgate Bumper is a quality reproduction of the original factory part. Made of a high-quality EPDM rubber, the bumper attaches to the vehicle body to support / cushion the tailgate closure.
Hood Bumper
p/n: 70-0991-42
Bumper, hood to fender ledge. Typically four (4) to six (6) used per car.Length: 1.15625 inches. Width: .3125 inches.
Stabilizer Link or Shock Grommet
p/n: 70-0737-33
This Stabilizer Link or Shock Grommet is designed from the original part for superior fitment and usage. Fully molded rubber.
Gearshift Seal
p/n: 20-2875-88
Seal, automatic transmission shifter housing to floor. Installs between housing and floor pan.
Hood to Fender Bumper
p/n: 70-1630-42
This Hood to Fender Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure. Four (4) to six (6) required per vehicle.
2-1/4" Body Hole Plug
p/n: 35-0863-45
This Body Hole Plug is fully molded and designed from the original part for superior fitment and seal. Designed for the trunk, however the generic shape makes this plug usable for a variety of applications.
Instrument Bezel To Bezel Glass Seal
p/n: 70-4941-88
This Instrument Bezel To Bezel Glass Seal is designed from the original part for superior fitment and seal. This part seals the glass to the Instrument Panel / Bezel.
13/16" Door Weatherstrip without Clips
p/n: 70-1244-73
This Door Weatherstrip is made from high-quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
Hood to Fender Bumper
p/n: 70-1963-42
This Hood to Fender Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.