Anti-Rattle Gravel Guard Deflector - Front or Rear Bumper
p/n: 70-0569-30
Manufactured to OEM standards, this Anti-Rattle Gravel Guard Deflector is for the front or rear bumper mounting bar depending on vehicle model. Metal with rubber covered end. Installs for an authentic fit and finish.
Bumper Grommet
p/n: 10-0167-28
Grommets, front and rear bumper arm. Fully molded rubber, slightly angular.
Bumper Grommet
p/n: 30-0039-28
Grommets, front or rear bumper. On models without trunk racks. Two (2) pair used per car if needing both front and rear bumper grommets.
Bumper Grommet
p/n: 40-0047-30
Grommets, front or rear bumpers, right and left. Two (2) pair used per car if needing both front and rear bumper grommets. Fully molded rubber.
Bumper Grommet
p/n: 40-0048-30
Grommets, bumper. Some front and some rear, right and left. Fully molded rubber.
Bumper Seal
p/n: 70-0978-45
Filler valance or deflector, rear. Extruded rubber to correct cross section. Fifty five (55) inches long.Length: 55.0 inches. Height: .28125 inches.
Bumper Seal
p/n: 70-0563-45
Filler valance or deflector, rear. Eight (8) inches long (cut shorter where required), three (3) to four (4) required per car.
Bumper Support Bar Pad
p/n: 70-0993-30
Bumper, impact bar end to body, for rear bumper. Fully molded rubber. Two inches (2") length by seven sixteenths inch (7/16") width by eleven sixteenths inch (11/16") height.
Bumper Support Bar Pad
p/n: 60-0420-30
Pads, rear bumper bar, inner, to quarter panel. Fully molded rubber.
Chrome Bumper To Body Splash Shield Filler
p/n: 70-4858-47
This Chrome Bumper To Body Splash Shield Filler is designed from the original part for a superior fitment. This bumper filler is approximately fifty-eight and three-eighths (58-3/8") inches long and fits between the vehicle body and the chrome rear bumper.</p>
Fender Bumper
p/n: 33-0545-30
Bumper, fender extension to quarter panel. Fully molded rubber. One and one fourths inch (1-1/4") length by eleven sixteenths inch (11/16") base diameter.
Front and Rear Bumper Spacer
p/n: 70-0184-30
Spacer or mute, front and rear bumper mounting bar to gravel deflector. Fully molded rubber. Two and nine sixteenths inch (2-9/16") outside length by seven eighths inch (7/8") width by thirteen sixteenths inch (13/16") height.
Front Bumper Gravel Shield Mute
p/n: 30-0399-29
These Front Bumper Gravel Shield Mutes are fully molded out of quality EPDM rubber. They are sold as a pair to fit on the outer bumper brackets. Designed to slide over the outer bumper to put tension on the bottom of the shield to prevent rattle.
Front Bumper Grommet
p/n: 27-0004-28
Grommet, front or rear bumper. Hollow construction, perfect fit. Note: In 1935 this grommet is used on the front bumper. In 1937-1938: this bumper is used on the rear bumper.
Front Bumper Grommet
p/n: 27-0054-28
Grommet, front bumper. Fully molded rubber, detailed and flanged as original.
Gravel Shield
p/n: 60-0524-30
This Gravel Shield is designed from an original part so it fits correctly. The seal installs to the rear apron to bumper. Sold as a sixty-six (66) inch strip.
Gravel Shield Bumper
p/n: 33-0286-30
Bumper, rear gravel shield, anti-rattle. Five (5) or more used per car. Fully molded rubber. Replaces factory #1320392.
Plastic body filler
p/n: 70-2265-30
Rear bumper corner. Seals between body and bumper on each end. Fully molded with proper details of long lasting rubber. Replaces #1387314-5.