Carburetor Air Intake Hose
p/n: 70-0290-41
Hoses, carburetor air intake. Two (2) per car. Sixteen and three fourths (16-3/4) inches long, two (2) inches inside diameter one end, two and one fourth (2-1/4) inches inside diameter other end. Trim to proper length when installing.
Shaker Hood Air Cleaner Seal
p/n: 20-2766-45
This Shaker Hood Air Cleaner Seal includes drain hose and correct FoMoCo script. Made from Original Ford Tooling.
Fuel Neck Grommet
p/n: 30-0157-41
Seal, fuel filler neck through rumble seat floor pan. Highest quality workmanship, rubber with brass core as original.
Air Inlet Hose
p/n: 70-0405-41
Hose, air inlet, radiator shroud to air silencer. Two and one eighths (2-1/8) inch outside diameter by nine and three eighths (9-3/8) inch long. Beautiful copy of rare original part.
Fuel Tank Filler Hose Set - Midship Tank
p/n: 70-5006-41
This Fuel Tank Filler Neck Hose is designed from the original part for superior fitment and function. This fuel resistant rubber hose set connects the midship fuel tank to the filler pipe on Styleside models.
Fuel Neck Grommet
p/n: 30-0099-41
Grommet, fuel filler neck. Three and one half (3-7/16) inch inside diameter for four (4) inch hole in apron.
Fuel Neck Grommet
p/n: 25-0013-41
Grommet, fuel filler neck. Virtually exact copy for two and one fourth (2-1/4) inch diameter filler neck through body or fender.
Fuel Filler Neck Grommet
p/n: 30-0158-41
This Fuel Filler Neck To Body Grommet is designed from the original part for superior fitment and seal. This grommet fits around the vehicles fuel filler neck between the filler neck and vehicle body.
Fuel Neck Grommet
p/n: 30-0101-41
Grommet, fuel filler neck. For inside of body, on floor of wheel carrier.
Fuel Neck Grommet
p/n: 30-0241-41
Grommet, gas tank inlet to wheel housing. Also used as grommet, gas tank inlet tube to wheel compartment bottom.
Fuel Filler Neck Lower Cover Collar Seal
p/n: 70-3700-39
This Fuel Filler Neck Lower Cover seals the neck where it goes through rear fender splash panel on the trunk floor. Part is fully molded rubber with a corrosion resistant brass core.
Fuel Filler Neck Bezel Mounting Pad
p/n: 16-0001-41
A Fuel Filler Neck Bezel Mounting Pad. Good copy of the original. Length: 5-3/4 inches.
Fuel Tank Filler Hose
p/n: 70-5009-41
This Fuel Tank Filler Hose is designed from the original part for superior fitment and function. This molded fuel resistant rubber hose connects the fuel tank to the filler pipe.
Accelerator Lever to Accelerator Shaft Seal
p/n: 70-4098-40
This Accelerator Lever to Accelerator Shaft Seal is designed from the original part for superior fitment and seal. This seal mounts directly to cover and protect the accelerator lever to accelerator shaft rod linkage connection.
Fuel Line Grommet
p/n: 30-0045-41
Grommet, fuel gauge and gas line through rear frame cross member. For five eighths (5/8) inch by two and three eighths (2-3/8) inch slot.Length: 2.
Accelerator Rod Seal
p/n: 60-0136-41
Grommet, accelerator rod through toe board. Brass core and center bushing as original.
Fuel Tank To Apron Anti-Squeak Channel and Plugs
p/n: 20-2014-41
This Fuel Tank To Apron Anti-Squeak Channel and Plugs set is designed from the original part for an authentic fit, finish, and appearance. Rubber channel fits between the fuel tank and apron. Includes 4 rubber bumper plugs.
Fuel Tank Filler Hose - Front Tank
p/n: 70-5010-41
This Front Tank Fuel Tank Filler Hose is designed from the original part for superior fitment and function. This molded fuel resistant rubber hose connects the front fuel tank to the filler neck pipe.
