Rear Door weatherstrip
p/n: 70-1904-72
Door edge weatherstrip. This part is the primary door to body weatherstrip. Includes 26 sockets.
Rear Door Weatherstrips
p/n: 60-0592-72
This Rear Door Weatherstrip pair is designed from the original part for superior fitment and seal. These weatherstrips mount around the front, bottom, and rear of the rear doors using pre-installed clips.
Rear Door Weatherstrips
p/n: 50-0481-72
This Rear Door Weatherstrip pair is designed from the original part for superior fitment and seal. These primary door weatherstrips mount (pin-on) directly to the left and right rear doors sealing the full perimeter of the doors against the vehicle body when the door is closed.
Rear Engine Support Mounts
p/n: 25-0061-11
These Engine Support Mounts pair are fully molded to heavy steel cores as original. The supports are for the rear right and left engine mounts for models with Hydramatic transmission.
Rear Grill to Body Seal
p/n: 70-3124-31
This Rear Grill to Body Seal is designed from the original part for superior fitment and seal. This seal mounts on the top edge of REAR grill above the rear bumper.
Rear Leaf Spring Insulator
p/n: 70-0980-32
This Rear Leaf Spring Insulator is an exact replacement for the upper and lower spring pad. Two and one half (2-1/2) inches wide, with cloth reinforcement. Four (4) used per car.
Rear Spring Pad
p/n: 20-1275-32
This Rear Spring Pad is used as a spring insert silencer. The leaf spring insulator installs between the leaves.
Rear View Mirror Mounting Pad
p/n: 70-3082-70
This single Rear View Mirror Mounting Pad To Door gasket is designed from the original part for superior fitment and seal. The gasket is precision die cut to the original specifications. This gasket is for one (1) door mounted rear view mirror.
Rear Window Gasket
p/n: 60-0528-81
This Rear Window Gasket mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit. This is for vehicles without the upper inside garnish molding.
Rear Window Gasket
p/n: 70-1729-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rear Window Gasket
p/n: 60-0554-81
This Rear Window Gasket mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit. Fitted gasket provides a formed, seamless seal.
Rear Window Gasket
p/n: 70-0826-81
This Rear Window Gasket mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit. Fitted gasket provides a formed, seamless seal.
Rear Window Gasket
p/n: 20-0734-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rear Window Gasket
p/n: 20-0733-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rear Window Gasket
p/n: 60-0497-81
This Rear Window Gasket mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit. This is for vehicles WITHOUT the upper inside garnish molding, except for Pontiac models WITH upper inside garnish molding.
Rear Window Gasket
p/n: 60-0553-81
This Rear Window Gasket mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
Rear Window Gasket
p/n: 20-1962-81
This Rear Window Gasket mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
Rear Window Gasket
p/n: 20-1959-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rear Window Gasket
p/n: 60-0498-81
This Rear Window Gasket mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit. This is for vehicles with the upper inside garnish molding.
Rear Window Gasket
p/n: 70-2477-81
This Rear Window Gasket mounts around the full perimeter of the back glass and has properly molded corners. It also has the slot to accommodate the outer edge's decorative molding.
Rear Window Gasket
p/n: 20-1386-81
This Rear Window Gasket mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
Rear Window Gasket
p/n: 20-1956-81
This Rear Window Gasket mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
Rear Window Gasket Set
p/n: 60-0380-81
This Rear Window Gasket Set mounts around the two (2) separate back windows. They have vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rear Window Gasket Set
p/n: 60-0182-83
This Rear Window Gasket Set contains the rear window gasket itself and the locking strip. Both strips comes in a thirteen foot, one inch (13' 1") piece and mount around the full perimeter of the back glass. The ends may require trimming and bonding for installation.
Rear Window Gasket Set
p/n: 70-1623-81
This Rear Window Gasket Set contains the rear window gasket itself and the locking strip. The seal mounts around the full perimeter of the back glass and the locking strip holds it tight for a precise, factory fit.
Rear Window Gasket Set
p/n: 40-0510-83
This Rear Window Gasket Set contains the rear window gasket itself and the locking strip. The seal mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
Rear Window Gasket Set
p/n: 60-0082-83
This Rear Window Gasket Set contains the rear window gasket itself and the locking strip. Both strips comes in a ninety inch (90") piece and mount around the full perimeter of the back glass. The ends may require trimming and bonding for installation.
Retractable Front Roof Weatherstrip
p/n: 20-1935-67
Weatherstripping, front roof rear. Has special molded ends.
Retractable Hardtop Roof Rail Weatherstrips
p/n: 20-1916-65
This Retractable Roof Rail Weatherstrip pair is designed from the original part for superior fitment and seal. These roof rails seals fit on the folding roof of the vehicle and seal the side windows when the window is fully raised.
Retractable roof weatherstrip
p/n: 20-1922-67
Seals, body to rear side of top. Glues to top of quarter where sides of top set on body when top is up.
Retractable roof weatherstrip
p/n: 20-1927-67
Weatherstripping, rear roof side. Glues on top of rear quarter.
Retractable roof weatherstrip
p/n: 20-1933-67
Weatherstripping, front roof side assembly. Cloth covered like original. Installs on side of flapper.
Retractable roof weatherstrip
p/n: 20-1921-67
Pads, flapper. (Front of top rests on when top is down.) Glues to top of wheel well.
Retractable roof weatherstrip
p/n: 20-1934-67
Weatherstripping, rear roof front. Seal has special molded ends.
Rigid Run Channel
p/n: 20-1747-58
Channel, door glass run. Lock side. Rear of front door. This glass run installs on your original brackets.
Rigid Run Channels
p/n: 70-0536-58
A Rigid Run Channel pair with bright beaded edge, mohair lined channel, die trimmed and round formed at the top. Sold in 29" pairs.
Rigid Run Channels
p/n: 70-0347-58
This Rigid Run Channel pair is stainless beaded and mohair-lined to help eliminate window rattles and provide a smooth sliding surface for glass movement. Also works to protect the glass.
Rigid Run Channels
p/n: 70-0516-58
This Rigid Run Channel pair is zinc plated steel with black cloth inside lining to provide a smooth sliding surface for glass movement. Also works to protect the glass. Fastens in place by small screws or rivets on top and bottom.
Rocker Panel Inner Drain Cover
p/n: 70-2392-45
This Rocker Panel Inner Drain Cover pair is designed from the original part for superior fitment and seal. Fully molded with proper attaching teeth and flap.
Running Board or Inner Fender Splash Filler
p/n: 60-0288-45
This eight (8) foot Splash Filler strip is used for the running board apron to body or fender splash panels anti-rattle filler. This filler strip is top-quality EPDM sponge rubber to accept rivets or retaining screws.
Shift Lever Grommet
p/n: 50-0284-24
Grommet, shift lever insulator. One (1) per car. Three eighths (3/8) inch inside diameter by five eighths (5/8) inch barrel by one half (1/2) inch long.
Shifter Bushing Set - Column Shift
p/n: 20-1435-26
This Shifter Bushing Set is designed from the original part for superior fitment and function. This bushing set will restore and tighten that loose and sloppy column shift gear selector to a like new condition.
Shock Absorber Bushing
p/n: 70-0547-32
This Shock Absorber Bushing is manufactured with high-quality EPDM rubber to OEM specifications. The bushing is the double cone style. Designed from original part to ensure proper fit.
Shock Absorber Bushing
p/n: 70-0541-33
This Shock Absorber Bushing is manufactured with high-quality Nitrile rubber to OEM specifications. The bushing is the single cone style. Designed from original part and made of high-quality Nitrile dense rubber to ensure durability.
Shock Absorber Grommet
p/n: 60-0235-33
This Shock Absorber Grommet is fully molded and designed from the original part for superior fitment and durability. The grommet the plain cylinder type with flat ends for shock absorber mounting.
Shock and Stabilizer Grommet
p/n: 70-0274-33
This Shock and Stabilizer Grommet is fully molded using EPDM dense rubber. Designed from original with locating collar. Eight (8) required per car.
Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
Side Window Vertical Leading Edge
p/n: 70-0815-80
This quarter to side window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. This part attaches to the vertical edge of the rear side windows when the rear side windows are fully raised.
Side Window Vertical Leading Edge
p/n: 20-1951-80
This side to quarter window Vertical Leading Edge pair attaches to the vertical edge of the rear side windows when the rear side windows are fully raised. This molded rubber weatherstrip pair does not include the chrome piece that attaches directly to the glass.
Side Window Vertical Leading Edge
p/n: 70-0958-80
This quarter to side window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. This part attaches to the vertical edge of the rear side windows when the rear side windows are fully raised.
Side Window Vertical Leading Edge
p/n: 70-1271-80
This quarter to side window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. This part attaches to the vertical edge of the rear side windows when the rear side windows are fully raised.
Sliding Quarter Window Weatherstrip
p/n: 70-0353-78
This Sliding Quarter Window Weatherstrip is used for side window inner and/or outer, front and/or rear doors. Available in a 6ft. lengths.
Solenoid Plunger Boot
p/n: 60-0567-21
Boot, solenoid plunger, starter switch at starter.Height: 1.625 inches.
Spark Plug Wire Spacer
p/n: 70-0394-21
This Spark Plug Wire Spacer is designed from the original part for superior fitment and function. This spacer fits spark plug wires into the organizer bracket.
Speedometer Cable Grommet
p/n: 20-0435-41
This Speedometer Cable Grommet is generally used where the speedometer cable goes through the sheet metal of the firewall. Designed from the original part for superior fit and seal.
Splash Apron
p/n: 20-1867-45
This four (4) piece Splash Apron pair is designed from the original part for superior fitment and seal. Installs on the fender splash apron.
Splash Apron / A-Arm Dust Shield
p/n: 70-2506-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Splash Apron / A-Arm Dust Shield
p/n: 70-3066-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Splash Apron / A-Arm Dust Shield Filler
p/n: 70-3068-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler pair is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Left and Right pieces fit over suspension a-arms and inside front inner fenders.
Splash Apron / A-Arm Dust Shield Filler Set
p/n: 70-2494-45
This ten (10) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Spring Clamp Liner Set
p/n: 20-1272-32
Six (6) piece Spring Clamp Liner Set. The front spring takes eight pieces for both sides and the rear spring takes four pieces for both sides.