Rear Window Gasket
p/n: 70-0084-77
This Rear Window Gasket comes in a seven foot, six inch (7' 6") strip and mounts around the full perimeter of the back glass. The ends may require trimming and bonding for installation.
Rear Window Gasket
p/n: 20-0394-81
This Rear Window Gasket is made just like the original and mounts around the full perimeter of the back glass. The ends may require trimming and bonding for installation.
Rear Window Gasket
p/n: 70-0673-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rear Window Gasket
p/n: 30-0392-81
This Rear Window Gasket mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit. Designed to be used with reveal molding (not included).
Rear Window Gasket
p/n: 60-0367-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rear Window Gaskets
p/n: 60-0499-81
This Rear Window Gasket pair mounts around the two (2) separate back windows. They have vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Red Brake and Clutch Pedal Pad
p/n: 30-0188-89
Pads, brake and clutch pedal, slip over type. Black and red rubber. For black only see our #30-0188-22.Length: 3.875 inches. Width: 2.875 inches.
Ride Regulator Control Grommet
p/n: 70-0344-33
Grommets, ride regulator control rod through fender splash shield. Two (2) per car.Length: 5.875 inches. Width: 1.75 inches.
Ride regulator control grommet
p/n: 70-0639-33
Grommets, ride regulator control rod through fender splash shield. Two (2) per car. Made without rod hole. You cut rod slot as required at installation.
Ride Regulator Control Grommet
p/n: 70-0332-33
Grommets, ride regulator control rod through fender splash shield. Two (2) required per car.Length: 2.4375 inches. Width: 2.0 inches.
Rigid Run Channel
p/n: 30-0180-57
Channel, rigid run, for vent window division bar. Chrome beaded edge, mohair lined steel channel to proper dimensions for window side of wing window frame.
Rigid Run Channels
p/n: 70-0347-58
This Rigid Run Channel pair is stainless beaded and mohair-lined to help eliminate window rattles and provide a smooth sliding surface for glass movement. Also works to protect the glass.
Roof Tack Strip Insert
p/n: 20-2032-45
This Roof Tack Strip Insert is designed from the original part for superior fitment and seal. This insert strip fits between roof insert and the body of the vehicle. Closed Cars Only
Rumble Seat Lid Bumper Pad
p/n: 60-0191-87
Bumper pad, rumble seat lid, upper corners. Compare with our #70-0120-87.Width: 1.0 inches. Height: 1.125 inches.
Rumble Seat Step Mounting Pad
p/n: 70-0043-44
Pad, rumble seat step mounting for fender, double beaded edge per original. Width: 4.375 inches.
Rumble Seat Step Pad
p/n: 40-0055-44
Pad, rumble seat step, with "DeSoto" logo, full slipover type to fit old carcass and outer trim ring. See also our #40-0353-44.Height: .50 inches.
Rumble Seat Step Pad
p/n: 60-0126-45
Pad, rumble seat step, on rear bumper bracket or fender. Rubber cover only, full slip-over type with bowtie emblem.
Rumble Seat Step Pad
p/n: 60-0501-45
Step pad, rumble seat, on rear fender, with bowtie emblem. Steel core with bolt.Width: 4.375 inches. Height: 5.25 inches.
Rumble Seat Step Pad
p/n: 20-2031-45
This Rumble Seat Step rubber pad is designed from the original part for superior fitment and seal. This step pad fits on the vehicle rear fender to provide a step into the rumble seat.
Run Channel Retaining Clip
p/n: 60-0374-58
This Run Channel Retaining Clip is designed from the original part for an authentic fit, finish and function. Clip fits at the end of door window run channel. Tempered spring steel.
Running Board Center Strip
p/n: 30-0034-49
Running board center strip. Fits original metal retainer. Authentic reproduction with correct detail.
Running Board Matting
p/n: 40-0293-49
Running board Matting. Fully molded with all original details. Includes integral flaps of rubber on 3 sides to cushion fenders and splash apron. No splicing or butting required.
Running Board or Inner Fender Splash Filler
p/n: 60-0288-45
This eight (8) foot Splash Filler strip is used for the running board apron to body or fender splash panels anti-rattle filler. This filler strip is top-quality EPDM sponge rubber to accept rivets or retaining screws.
Shock Absorber Arm Bushing
p/n: 30-0192-32
Bushing, shock absorber arm. Restore proper shock action.Height: 1.375 inches.
Shock Absorber Arm Bushing
p/n: 60-0106-32
This Shock Absorber Arm Bushing is designed from the original part for superior fitment and function. Manufactured to OEM original standards.
Shock absorber bushing
p/n: 30-0407-33
Bushings, shock absorber. Set includes eight (8) large and eight (8) smaller bushings.
Shock Absorber Bushing
p/n: 50-0087-33
Bushing, Delco type, shock absorber link. One and five sixteenths (1-5/16) inch outside diameter, seven sixteenths (7/16) inch inside diameter.
Shock Absorber Link Arm Bushing
p/n: 60-0216-33
This Shock Absorber Link Arm Bushing is designed from the original part for superior fitment, finish and function. This bushing is for double acting shock absorber arm links.
Shock and Stabilizer Seal
p/n: 70-1184-33
Seals, shock absorber and rear stabilizer link. Eight (8) piece set. Width: 1.1875 inches.
Shock and stabilizer seal
p/n: 70-1185-33
Seals, shock absorber and rear stabilizer link. Eight (8) piece set.
Shock or Stabilizer Link Cross Pin Bushing
p/n: 50-0220-32
This Shock or Stabilizer Link Cross Pin Bushing is designed from the original part for superior fitment and function. A rubber bushing for shock absorber link cross pin or stabilizer cross link pin.
Side Mount Clamp Cushion
p/n: 40-0138-37
Cushion, sidemount clamp. Two and one eighth (2-1/8) inch by four and five eighths (4-5/8) inch.Length: 4.625 inches. Width: 2.125 inches.
Side Mount Grommet
p/n: 40-0140-37
Grommet, sidemount carrier brace to fender. One and five sixteenths (1-15/16) inch outside diameter by one half (1/2) inch inside diameter.
Side Mount Grommet
p/n: 30-0041-37
Grommets, sidemount support arm, right and left.Length: 5.50 inches. Width: 4.25 inches.
Side Mount Spare Grommet Set
p/n: 70-0180-37
This Side Mount Spare Grommet Set is made from top-quality EPDM rubber and designed from the original parts for durability and proper function. This set is for the rear spare wheel mount on cars without a luggage rack.
Side Mount Spare Wheel Grommet
p/n: 70-0341-37
Grommets, sidemount. These are the very large type, right and left. Used simultaneously with our #70-0388-37. Compare with your original. (See also our #70-0388-37).
Side Mount Spare Wheel Grommet
p/n: 70-0388-37
Grommets/seals, for sidemounted spares, cover hole in fender. Large, fully flanged for fender metal, compare to our #70-0341-37 and your original. Symmetrical, right and left. Approximately five and three fourths (5-3/4) inches by eight (8) inches outside
Side Mount Spare Wheel Grommet
p/n: 50-0082-37
Grommet set, side mounted spare wheel brace. Four (4) piece set with two (2) different sizes.
Side mount spare wheel grommet
p/n: 60-0331-37
Grommet, sidemount wheel carrier-through-fender, right and left.
Side Roof Rail Weatherstrip
p/n: 14-0001-80
Fifteen (15) foot strip for convertible side window fits aluminum retainer channel.
Side Roof Rail Weatherstrip
p/n: 30-0035-65
Weatherstrip, side window, rubber only. Fits in metal retainer as shown. Available by the foot.
Side Roof Rail Weatherstrip
p/n: 40-0095-65
Weatherstrip, convertible top to side windows. Fifteen sixteenths (15/16) inch by five eighths (5/8) inch. Sold in twelve (12) foot strips only.
Side Roof Rail Weatherstrip
p/n: 70-0251-65
Weatherstrip, side window. Base fifteen sixteenths (15/16) inch wide but easily trims to more narrow channel if necessary.
Side Roof Rail Weatherstrip
p/n: 20-2225-65
Seal, top iron to door glass. One (1) inch wide by thirty (30) inch length.
Side Window Lower Bump Stop
p/n: 70-0110-62
This Side Window Lower Bump Stop is designed from the original part for an authentic fit, finish, and function. Requires two (2) stops per window.
Side Window Roller
p/n: 70-0117-62
This Side Window Roller, anti-rattle roller, is manufactured using EPDM dense rubber to replace the original perfectly. The roller fits both styles of brackets.
Side Window Run Channel
p/n: 70-1169-58
Channel, side window, pre-flocked, 9/16" wide to accommodate metal frame side window. Available by the foot.
Side Window Run Channel
p/n: 70-1168-58
Side window run channel pre-flocked for 1/4" glass. Available by the foot.
Side Window Run Channels
p/n: 20-2058-58
This high-quality material Side Window Glass Run Channel set is the run channel that holds the glass in place. Complete set for Coupe and Sedan with a center mounted inside door handle, does both doors.
Spare Wheel Carrier Grommet
p/n: 40-0254-37
Grommet, rear spare wheel carrier bracket hole. Two (2) per car.Length: 4.1875 inches.
Spark plug grommet
p/n: 70-1180-21
Grommet, spark plug & coil wire at distributor cap outlets. For nine (9mm) millimeter wire, earlier years.
Spark plug grommet
p/n: 70-1181-21
Grommet, spark plug and coil wire at distributor cap outlets. For seven (7mm) millimeter, later years.
Spark plug retaining ring
p/n: 30-0352-21
Retaining ring, spark plug wire. Two (2) per car.Chevrolet 1935-48 Retaining ring, spark plug wire. Two (2) per car. All models.
Spring or Stabilizer Bushing
p/n: 11-0020-35
Bushing, spring bracket on frame (Auburn and Cord 810 & 812). Also used as a grommet, front stabilizer bar (Graham models 116 & 120). Fully molded rubber.
Spring shackle bushing
p/n: 11-0014-32
Bushing, spring eye leaf and shackle bolt, 1-1/2" barrel diameter with 1/2" inside diameter hole. Replaces Harris #998.
Spring Shackle Pin Neoprene Washer
p/n: 70-1125-33
This Spring Shackle Pin Neoprene Washer is designed from the original part for superior fitment and function. Rubber washer fits the front and or rear spring shackle pin. Constructed of neoprene rubber.
Stabilizer Grommet
p/n: 70-0436-33
Grommet, front stabilizer bar link or rear shock link to axle. Fully molded rubber. Eight (8) required per car.
Starter Button Cover
p/n: 60-0322-21
This Starter Button Cover is designed from the original part for an authentic fit, finish, and appearance. A push on replacement to rod. Two (2") inch outside diameter.
Starter Pedal Button Cover
p/n: 60-0166-21
This Starter Button Pedal Cover is designed from the original part for an authentic fit, finish, and appearance. Rubber slip over type for old metal. Two (2") inch outside diameter.
Steering Column Cushion - Black
p/n: 60-0012-36
This Steering Column Cushion grommet is designed from the original part for an authentic fit, finish, and appearance. For the steering column to cowl U-bolt clamp. Black rubber. For Brown see 60-0012-89.
Steering Column Cushion - Brown
p/n: 60-0012-89
This Steering Column Cushion grommet is designed from the original part for an authentic fit, finish, and appearance. For the steering column to cowl U-bolt clamp. Brown rubber. For Black see 60-0012-36
Steering Column Floorplate
p/n: 17-0001-36
Grommet, steering column floor, black rubber only, excellent copy of original.Length: 5.0 inches.
Steering Column Floorplate
p/n: 17-0006-36
Floorplate, steering column and pedals, black rubber only, excellent detail.Length: 12.625 inches. Width: 7.5 inches.
Steering Column Floorplate
p/n: 50-0117-36
Floorplate at steering column and pedals. Black rubber. For brown see our #50-0117-89. Metal core as original.Width: 9.25 inches.
Steering Column Floorplate
p/n: 70-0340-88
Seal, steering column to toe board. Three fourths (3/4) inch thick, high grade sponge, die cut holes.Length: 3.875 inches. Width: 3.875 inches.
Steering Column Grommet
p/n: 30-0160-36
Grommet, steering column to toe board. One and five eighths (1-5/8) inch hole for column. Similar to, but larger than our #30-0046-36. Length: 5.25 inches.