Hood to Cowl Weatherstrip
p/n: 27-0075-42
This Hood to Cowl Weatherstrip mounts around the rear of the engine bay to seal between the hood and vehicle body cowl. The pair is twenty-one (21) inches in length and nine-sixteenths (9/16) inch in width to provide complete coverage.
Front Stabilizer Bushing
p/n: 50-0094-34
Bushings, front stabilizer shaft-to-frame or stabilizer shaft, front or rear. Fully molded rubber.
Brake and Clutch Shank Seal
p/n: 30-0143-24
Boot, brake and clutch pedal shank at toe board.Length: 2.9375 inches.
Gearshift Boot
p/n: 70-2126-24
Boot, transmission gear hand shift lever. Molded in pliable black rubber which may be painted if needed for restoration.
Headlight Door To Lens Ring Seals
p/n: 70-0389-14
This Headlight Door To Lens Ring seal pair is designed from the original part for superior fitment and function. The part works to seal between the headlight door housing and the headlight retaining ring. The part is a single lip type seal for sealed beam headlights.
Taillight and License Plate Bracket Mounting Pad
p/n: 60-0493-17
This reproduction Taillight and License Plate Bracket Mounting Pad is designed from the original part for an authentic fit, finish, and appearance.
Fuel Neck Grommet
p/n: 70-1616-39
Grommet, fuel neck. Fully molded rubber with retaining flange. Three and eleven sixteenths inch (3-11/16") outside diameter by two and one eighth inch (2-1/8") inside hole diameter by nine sixteenths inch (9/16") height.
Running Board or Inner Fender Splash Filler
p/n: 60-0288-45
This eight (8) foot Splash Filler strip is used for the running board apron to body or fender splash panels anti-rattle filler. This filler strip is top-quality EPDM sponge rubber to accept rivets or retaining screws.
Bumper Support Bar Pad
p/n: 60-0420-30
Pads, rear bumper bar, inner, to quarter panel. Fully molded rubber.
Vent Window Division Post Weatherstrips
p/n: 70-2013-56
This rear door Vent Window Division Post Weatherstrip pair is designed from the original part for superior fitment and seal. This part fits opposite the glass run channel and seals the vent window when the window is closed.
Vent division bar weatherstrip
p/n: 70-0781-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Vent Window Division Post Weatherstrips
p/n: 60-0494-56
This front door Vent Window Division Post Weatherstrip pair is designed from the original part for superior fitment and seal. Fully molded rubber with metal core and attaching tabs.
Vent Window Division Post Weatherstrips
p/n: 60-0569-56
This Front Window Vent Division Post Weatherstrip pair is fully molded with metal core and attaching tabs.
Vent division bar weatherstrip
p/n: 70-0821-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Window Felt Beltline Weatherstrips
p/n: 70-0555-58
These Window Felt Beltline Weatherstrips are sold as a three (3) foot pair. The beltline is used for side windows inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Clutch or Brake Pedal Pad - Black
p/n: 70-0176-22
This reproduction Clutch or Brake Pedal Pad slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Vent Window Division Post Weatherstrips
p/n: 60-0596-56
This Front Window Vent Division Post Weatherstrip pair is fully molded with metal core and attaching tabs.
Fuel Neck Grommet
p/n: 12-0001-39
Grommet, fuel filler neck. Fully molded rubber. Three and three fourths inch (3-3/4") outside diameter by one and seven eighths inch (1-7/8") inside diameter by three inch (3") sheet metal opening.
Cowl Vent Gasket
p/n: 12-0011-54
Gasket, cowl vent, molded sponge rubber to original size and configuration.
Flexible Run Channel
p/n: 70-1239-58
This Flexible Run Channel provides a smooth sliding surface while helping to eliminate rattle and protect the glass. The run channel has the stainless beaded edge and is cloth covered and mohair lined with the flexible metal channel.
Beltline Weatherstrips
p/n: 40-0539-57
This Beltline Weatherstrip pair installs on the left and right doors to wipe the inside and outside of the windows when the glass is lowered. Flexible, pile lined, rubber covered, with a black bead. Available in 3ft pair.
Vent division bar weatherstrip
p/n: 30-0346-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Vent division bar weatherstrip
p/n: 30-0347-74
Weatherstrip, rear vent window, front edge (on division post) right and left.
2-7/8" Firewall Grommet
p/n: 70-1747-20
This Firewall Grommet is used to pass the dash wires through the firewall. Designed from the original part for superior fit and seal.
Engine Snubber Pad Set
p/n: 30-0311-11
This four (4) piece Engine Snubber Pad Set is designed from original for correct fit and function. Sold only in complete sets. One four (4) piece set required per car.
Flexible Run Channel - 6 Ft.
p/n: 70-1108-57
Channel, flexible window run, un-beaded. Cloth covered mohair-lined type. Available in 6ft lengths.
Door Vent Window Foot
p/n: 20-2556-62
This Door Vent Window Foot installs at the base of the front door vent window frame. Sold as a pair.
Ignition Cable Grommet
p/n: 70-1598-21
Grommet, ignition cable.Length: 2.125 inches. Width: 1.50 inches.
Headlight Door To Lens Weatherstrips
p/n: 70-0493-14
This Headlight Door To Lens Weatherstrip pair is the double lip type for sealed beam headlights. The pair is molded without wire. Designed from the original part to fit correctly.
Rigid Run Channels
p/n: 70-0347-58
This Rigid Run Channel pair is stainless beaded and mohair-lined to help eliminate window rattles and provide a smooth sliding surface for glass movement. Also works to protect the glass.
Hood to Radiator Weatherstrip
p/n: 70-1580-42
Weatherstrip, hood to radiator shroud.Width: 1.3125 inches.
Gearshift Boot - Black
p/n: 20-0334-26
This reproduction Black Gearshift Boot is designed from the original part for an authentic fit, finish, and appearance.
Fuel Filler Neck Grommet
p/n: 60-0512-41
This Fuel Filler Neck Grommet is designed from the original part for superior fitment and seal. This grommet fits around the vehicles fuel filler neck between the filler neck and vehicle body. Fully molded rubber, slightly angled and oblong in shape.
Rear Engine Mount
p/n: 20-0421-11
This Rear Engine Mount helps eliminate engine vibrations. Used as a rear engine support or transmission mount. Designed with rubber over a metal core.
Front Bow Weatherstrip
p/n: 60-0440-64
Weatherstrip, front bow to windshield, outer. Installs on convertible top. Approximately four (4) foot ten (10) inches long.
Stabilizer Bushing
p/n: 27-0085-34
Bushings, for stabilizer bracket. Fully molded rubber. Correct dimensions, not an aftermarket replacement.
Hinge Seal Set
p/n: 60-0285-69
Seal, back door hinge, outside. A four (4) piece set. Some vehicles require two (2) sets.
License Light Mounting Pad
p/n: 60-0174-17
Pad. rear license light mounting. Two and three fourths (2-3/4) inch by three and nine thirty seconds (3-9/32) inch overall. Two (2) required per vehicle.
Brake and clutch pedal pad
p/n: 12-0013-22
Pads, brake and clutch pedals, perfect copy, top material.
Hood To Cowl Weatherstrips
p/n: 60-0428-42
This Hood To Cowl Weatherstrip pair is designed from original parts so it fits correctly. The pair comes ready to install with pre-punched holes.
Rear coil spring pad
p/n: 50-0359-35
Insulators, rear coil spring. Fabric reinforced rubber as original. One (1) pair per car.
Taillight Mounting Pad
p/n: 27-0062-15
Pad, taillight to body mounting. Right and left molded as original with proper bead lip. Length: 4.50 inches.