Fuel Neck Grommet
p/n: 60-0475-41
Grommet, fuel filler neck (1955-2nd type). Fully molded rubber, slightly oblong. Three and one half inch (3-1/2") outside width by three and fifteen sixteenths inch (3-15/16") outside length.
Hood To Cowl Weatherstrip
p/n: 60-0153-42
This Hood To Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact copy reproduction of the original profile. This weatherstrip installs at the rear of the engine bay to seal between the hood and vehicle body cowl.
Trunk Weatherstrip
p/n: 20-1389-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid.
Firewall Grommet
p/n: 70-0984-20
This Firewall Grommet is used to run the wiring harness through the firewall. Designed from the original part for superior fit and seal.
Stabilizer Bar End Link Repair Set
p/n: 20-1294-33
This eleven (11) piece Stabilizer Bar End Link Repair Set is designed to withstand harsh conditions without deteriorating. Two (2) end link sets required per car.
Roof Rail Filler
p/n: 60-0429-73
This Roof Rail Filler pair installs on the front corner of the side roof rail, just in front of the flipper seal. Molded as left and right with molded screw holes. High-quality EPDM rubber a solid brass core.
Air ventilator seal
p/n: 20-2965-31
Seals, air vent damper. Must drill out spot welds to replace the cracked rubber. Includes screws to put back together.
Rear Quarter Window Bumper
p/n: 70-1096-62
Bumper, rear quarter window. Made of molded neoprene rubber with steel washer core. Two (2) per car.Length: 1.0625 inches.
Clutch Rod Boot
p/n: 20-2949-23
This Clutch Rod to Firewall Boot is designed from the original part for superior fitment and seal. This boot makes a weathertight connection for the clutch rod lever as it passes through the firewall.
Brake and Clutch Shank Seal
p/n: 50-0066-24
Grommet, brake and clutch pedal floor seal.Width: 1.8125 inches. Height: 2.375 inches.
5" Wide Bow Drill Cloth Tape
p/n: 70-1175-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Black in color and available in a five (5) foot roll.
Windshield Frame to Cowl Weatherstrip
p/n: 70-3004-42
This Windshield Frame to Cowl Weatherstrip is designed from the original part for superior fitment and seal. This cowl rubber goes in between the windshield frame and cowl. This part also fits the 1952-1971 M38A1 model.
Gravel Shield Bumper Set
p/n: 60-0146-30
This Gravel Shield Bumper Set is used as a rear bumper deflector. Also used between the radiator grille and the lower panel. Two (2) required per car. Designed from the original part for superior fitment and seal.
Body Bumper Kit
p/n: 90-0206-90
This ten (10) piece Body Bumper Kit is designed from the original part for superior fitment, finish and function. Designed from originals and made from top quality rubber to ensure durability.
Headlight to Fender Gasket
p/n: 50-0563-14
Seal, headlight to fender. Die cut to original dimensions.Height: .125 inches.
Firewall Grommet
p/n: 70-1012-20
This Firewall Grommet is used to run the parking brake cable through the firewall. Designed from the original part for superior fit and seal.
Convertible Roof Rail Weatherstrip T-Bolt Set
p/n: 70-4606-67
These Convertible Top Roof Rail Weatherstrip T-Bolt reproductions are designed from the original part for superior fitment and function. This twenty two (22) t-bolts and twenty two (22) nut set fastens to the convertible top bow weatherstrips.
Drag Link End Repair Set
p/n: 20-0506-32
This Drag Link End Repair set is designed from the original parts for superior fit and function. This repair set will help your worn and aged steering connections to be once again as tight as the factory made them and help to make steering your classic truck easy again.
Window Division Bar Filler
p/n: 70-2661-62
This Window Division Bar Filler is sold as a four (4) piece set for the upper and lower. This filler set fits into inside garnish molding between rear seat side window and rear side window.
Parking Brake Pedal Pad
p/n: 50-0405-22
Pad, parking brake pedal. With "PARK" written on pad. Black only. For pedal pad without "PARK" written on pad see our #50-0348-22.Width: 2.0625 inches.
Trunk Weatherstrip
p/n: 70-1122-85
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid. The seal glues directly to the trunk lid.
Taillight Mounting Pad
p/n: 50-0100-15
Mounting pad, extrusion, taillight body-to-rear fender. Sold in sets sufficient for two (2) taillights. Length: 55.0 inches. Width: .3125 inches.
Power Window Switch Bezel Pad
p/n: 70-2137-21
Mounting pad, power window die cast bezel. Used under 4 way switch, typically found on drivers door.Width: 2.0 inches.
Steering Column Finish Strip
p/n: 70-1707-88
Seal, steering column to instrument panel. Extruded rubber strip thirteen (13) inch to exact cross-section.Length: 13.0 inches. Width: .625 inches.
Suspension arm bumper
p/n: 70-1021-32
Bumper, front or rear suspension, upper. Uses two (2) per car on front suspension, one (1) per car on rear.
Fender Skirt Edge Weatherstrip
p/n: 20-1316-44
This Fender Skirt Edge Weatherstrip pair is designed from original for superior fitment, finish, and seal. This weatherstrips fits between the rear wheel fender skirt and the rear fender quarter panel.
Vent division bar weatherstrip
p/n: 20-3042-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Rigid Run Channels
p/n: 70-0516-58
This Rigid Run Channel pair is zinc plated steel with black cloth inside lining to provide a smooth sliding surface for glass movement. Also works to protect the glass. Fastens in place by small screws or rivets on top and bottom.
Hood Bumper Set
p/n: 20-3004-42
This ten (10) piece Hood Bumper set is designed from the original parts for superior fitment and function.
Splash Apron
p/n: 20-3016-44
This six (6) piece Splash Apron set is designed from the original part for superior fitment and seal. Installs on fender splash apron and bottom of radiator side deflectors.
Vent Division Bar Weatherstrip
p/n: 20-3043-56
This Front Vent Division Bar Weatherstrip is fully molded with metal core and attaching tabs.
Windshield Post to Door Seal
p/n: 70-0304-73
Weatherstrip, windshield post, upper to door. Seals between front door vent window frame and windshield pillar. Top quality rubber made to original cross-section. Two (2) strips approximately fifteen (15) inches long. May need to trim ends to fit.
Headliner Seal
p/n: 20-0573-88
Headliner Seal - One hundred seventy six (176) inches long to hold Headliner - Goes Around The Interior Perimeter Of Cab.
Firewall Grommet
p/n: 70-0967-20
This Firewall Grommet is used to run the windshield washer, vacuum lines, antenna lead, and other wires through the firewall. Designed from the original part for superior fit and seal.
Front Door Hinge Pillar Weatherstrips
p/n: 70-0552-73
This Front Door Hinge Pillar Weatherstrip pair is designed from the original parts for superior fitment and seal. The pair attaches above the beltline, hinge pillar windshield post. These two (2) strips with pre-installed clips, one for each door, are manufactured for a factory like fit.
Vent Window Division Post Weatherstrips
p/n: 20-0562-56
Front vent window division post seal. This part fits opposite the glass run channel and seals the vent window when the vent is closed.
Antenna Mount Pads
p/n: 70-2264-21
This Antenna Mount Pad pair is designed from the original part for superior fitment and seal. For rear mounted twin (dual) antennas. See our 32-0390-21 for insulating Antenna Grommet pair.
Steering Column Gasket
p/n: 70-2317-88
Insulator, steering column lower mounting frame gasket. Triangular shape with mounting holes and column tube clearance.
Wiring grommet
p/n: 70-2113-20
Grommet, main wiring harness through firewall. Fully molded with proper lips and pass through holes for electrical lines.
Fabric Hood Lacing
p/n: 20-0354-42
This Fabric Hood Lacing installs where the hood rests on the cowl panel. Original woven style lacing complete with installation tacks. Sold as a forty-nine (49) inch strip.
Steering Column Floorplate
p/n: 60-0403-24
This Steering Column Floorplate is used as the steering gear and clutch pedal push rod dash seal. Fully molded with original style pattern. Does not have metal backing.
Radiator Mounting Pad Set
p/n: 20-0570-45
This Radiator Mounting Pad Set is designed from the original parts for a factory like appearance and function.
2" Wiring Harness Firewall Grommet
p/n: 70-1724-20
This Wiring Harness Firewall Grommet is used to run the main wiring harness through the firewall. Designed from the original part for superior fit and seal.
Leading Edge Weatherstrip
p/n: 70-2002-80
Rear door window vertical seals. Fully molded rubber with metal cores.
2" Firewall Grommet
p/n: 70-1725-20
This Firewall Grommet is used to run the windshield washer hose and antenna wiring through the firewall. Designed from the original part for superior fit and seal.
Brake Pedal Pad
p/n: 50-0349-22
This reproduction Pedal Pad slips over the full perimeter of the brake pedal for a precise, factory fit. For models with Power Brakes.
Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
Cowl Vent Gasket
p/n: 60-0270-54
Gasket, cowl vent. Labyrinth type as original.Length: 16.75 inches.
Peel-N-Stick Trunk Weatherstrip
p/n: 20-1389-WT
This Peel-N-Stick Trunk Weatherstrip is designed for superior fitment and seal. The weatherstrip mounts around the full perimeter of the trunk directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.
Front Door Division Bar Glass Run Channel
p/n: 20-3063-58
This Front Door Division Bar Glass Run Channel is designed from the original part for superior fitment and function. Ready for attaching to your original brackets. Length: 30 inches.
Fender Skirt Edge Weatherstrip
p/n: 60-0201-45
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment and seal. This weatherstrips fits between the removable fender skirt and the rear fender quarter panel.
Firewall Grommet
p/n: 30-0456-20
This Firewall Grommet is used for the heater core at the firewall. Designed from the original part for superior fit and seal.
Parking Light Lens Gasket
p/n: 70-1521-16
Gasket, parking light lens.Length: 14.875 inches. Width: 2.0 inches.
Rear Bumper Gravel Shield
p/n: 60-0173-30
This Rear Bumper Gravel Shield, also known as a rear bumper face bar-to-body seal, is made of high quality dense rubber. Fully molded rubber with all original features.
Fuel Neck Grommet
p/n: 20-0581-39
Grommet, gas tank neck. Oval shaped. Fully molded rubber with retaining flange. Three and thirteen sixteenth inch (3-13/16") outside width by four and five sixteenths inch (4-5/16") outside length.
Cab Running Board Seal
p/n: 20-0541-45
This Cab Running Board Seal is sold as a pair for the left and right side. These seals are two (2) inches in height.
Running Board Seal
p/n: 20-0542-45
This Running Board Seal is sold as a pair for the left and right side. These seals are two (2) inches in height. Fits Panel Trucks ONLY.
Headlight Mounting Pad
p/n: 70-0201-14
This Headlight Mounting Pad is designed from the original part for superior fitment and seal. This pad acts as the headlight adjusting collar. Sold as a pair.
Hood to Cowl Weatherstrip
p/n: 30-0527-42
Weatherstrip, hood to cowl. Overall thirty seven (37) inches long.
A-Arm Dust Shields Filler
p/n: 70-2772-45
This two (2) piece A-Arm Dust Shield Filler pair is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms only.
Flexible Run Channel - 5ft
p/n: 70-1107-57
Cloth covered mohair-lined type. For sides and top of side windows. Available in 5ft lengths.
Accelerator Pedal Pad
p/n: 60-0301-41
Pad, accelerator pedal. Slipover cover type. Exact copy. Fits original steel core. Length: 8.0 inches.
Front Stabilizer Bushing
p/n: 60-0088-34
This Front Stabilizer Bushing pair is fully molded from EPDM dense rubber to ensure durability. Used to connect the stabilizer bar to the vehicle frame. Two (2) required per car.
Splash Apron
p/n: 20-3013-44
This two (2) piece Splash Apron is designed from the original part for superior fitment and seal. This pair attaches to the inner fender to suspension arm.
Window Felt Beltline Weatherstrips
p/n: 80-1029-57
This Window Felt Beltline Weatherstrip is original equipment style side window horizontal seal kit (also known as beltline weatherstrip). Four (4) piece kit includes inner and outer felt beltline weatherstrip for each door window.
Suspension Bumper - Front Lower Control Arm
p/n: 50-0092-32
This Suspension Bumper is designed from the original part for superior fitment and function. Bumper mounts to the front suspension lower control arm. Two (2) per car required.
Radiator Splash Shield
p/n: 20-2959-31
This Radiator Splash Shield set is designed from the original part for superior fitment and seal. Set of 4.
Quarter Window Pads
p/n: 20-3124-79
This Quarter Window Pad pair is designed from the original part for superior fitment and seal. This is the front lower corner quarter window pad for Hardtops, Convertibles and Retractable Hardtop models.
Window Felt Beltline Weatherstrips - 3ft Pair
p/n: 30-0244-57
This side window Window Felt Beltline Weatherstrip pair can be used as inner and/or outer. The weatherstrip is flexible, pile lined, rubber covered, with black bead. Available in 3ft pairs.
Chrome Fender Welting - 25ft
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Sliding Quarter Window Weatherstrip
p/n: 70-0353-78
This Sliding Quarter Window Weatherstrip is used for side window inner and/or outer, front and/or rear doors. Available in a 6ft. lengths.
Axle Rebound Pad
p/n: 40-0252-32
Bumper, rear axle spring. Three (3) per car.Length: 2.1875 inches. Width: 1.0 inches. Height: 2.0 inches.
Liftgate Weatherstrip
p/n: 20-3144-85
This liftgate weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the sides and top of the liftgate opening directly to the body.
Radiator Top Seal
p/n: 40-0459-42
Seal, radiator yoke to air hood. Extruded rubber to original profile. Four (4) foot strip.Length: 48.0 inches. Width: 1.125 inches.
Upper Engine Mount
p/n: 20-0515-11
This Upper Engine Mount is a reproduction designed from the original part to fit correctly. Uses quality rubber for proper engine vibration isolation. One (1) required per truck.
Steel Sash Channel
p/n: 20-0514-62
This reproduction Steel Sash Channel is designed from the original part for superior fitment and function. This glass channel is for the Left or Right Front Door.
Beltline Weatherstrip
p/n: 40-0540-57
This six (6) foot Beltline Weatherstrip installs on the left and right doors to wipe the side windows when the glass is lowered. Flexible, pile lined, rubber covered, with black bead. Available in 6ft. lengths.
Flexible Run Channel
p/n: 70-1238-58
Cloth covered, mohair lined flexible metal channel for sides and top of door windows.
Clutch and Brake Pedal Pads - Brown
p/n: 50-0054-89
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality brown rubber.
Fog Light Lens Gasket
p/n: 70-1033-17
Gasket, fog light lens.Length: 8.5 inches. Width: 4.125 inches. Height: .125 inches.
Front Coil Spring Pad
p/n: 50-0476-35
Pad, front coil spring insulator, upper. Two (2) per car, five and one eighths (5-1/8) inch outside diameter. Height: .28125 inches.
Front Stabilizer Bushing
p/n: 50-0094-34
Bushings, front stabilizer shaft-to-frame or stabilizer shaft, front or rear. Fully molded rubber.
U Jamb lock pillar filler
p/n: 50-0519-79
Door lock pillar seal. This part seals the bottom of the rear side window, and may also be known as a door jamb seal.
Gearshift Boot
p/n: 70-2126-24
Boot, transmission gear hand shift lever. Molded in pliable black rubber which may be painted if needed for restoration.
Headlight Door To Lens Ring Seals
p/n: 70-0389-14
This Headlight Door To Lens Ring seal pair is designed from the original part for superior fitment and function. The part works to seal between the headlight door housing and the headlight retaining ring. The part is a single lip type seal for sealed beam headlights.
Brake and Clutch Pedal Pads
p/n: 20-0494-22
Pads, brake and clutch pedal. Three and one half (3-1/2) inch diameter.
Running Board or Inner Fender Splash Filler
p/n: 60-0288-45
This eight (8) foot Splash Filler strip is used for the running board apron to body or fender splash panels anti-rattle filler. This filler strip is top-quality EPDM sponge rubber to accept rivets or retaining screws.
Vent division bar weatherstrip
p/n: 70-1091-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Vent Window Division Post Weatherstrips
p/n: 60-0585-56
This Front Door Vent Window Division Posts Weatherstrip pair is fully molded with a metal core and attachment holes. This part fits opposite the glass run channel and seals the vent window when the vent is closed.