Front Engine Support
p/n: 70-0276-11
This Front Engine Support is designed from original parts for an exact reproduction. Constructed of rubber and steel for proper engine vibration isolation.
Window Felt and Run Channel Set
p/n: 90-0140-58
This eight (8) piece Window Felt and Run Channel set includes the inner and outer window felts, upper rigid run channels, and flexible run channels needed to complete two doors. The set can be used for front or rear doors in models with vent windows in the door.
Front Door Vent Window Set
p/n: 90-0366-90
This four (4) piece Front Door Vent Window Set contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Front Door Vent Window Weatherstrips
p/n: 38-0016-55
These Front Door Vent Window Weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Front Door Weatherstrip Set
p/n: 90-0104-72
This Front Door Weatherstrip Set is the primary door to body weatherstrip. Includes 22ft. (11ft. per door) of main door weatherstrip, 7ft. (3-1/2 ft. per door bottom weatherstrip and 20 fastener clips for easy installation.
Rear Window Gasket
p/n: 60-0278-81
This Rear Window Gasket mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Engine Mount Service – Revulcanization Only
p/n: 70-0629-11
This Revulcanization Service Only is designed to restore your Rear Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Windshield Gasket
p/n: 70-0535-50
This Windshield Gasket mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Door Weatherstrip
p/n: 70-0085-73
Weatherstrip, door opening, fits retainer under edge of body sill to form seal when door is closed. Six (6) foot strips.Length: 72.0 inches. Width: 1.
Front Spring Bumpers - Lower Suspension Arms
p/n: 70-0172-32
This Front Spring Bumpers pair is designed from the original part for an authentic fit, finish, and appearance. These front spring bumpers install to the lower suspension arms. An original copy reproduction.
Trunk Weatherstrip
p/n: 70-0796-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid.
Coil spring insulator pad
p/n: 70-0801-32
Pad, coil spring insulator. Molded four (4) piece set for one (1) car.
LaSalle monogram pedal pad
p/n: 70-0037-22
LaSalle pedal pads, clutch and brake, excellent copy from authentic original with LaSalle monogram.
Side Deflector / Valance Rubber
p/n: 70-0092-45
This Side Deflector / Valance Rubber pair is designed from the original part for superior fitment and seal. Each deflector piece is approximately 6 feet long.
Rigid Run Channels
p/n: 70-0536-58
A Rigid Run Channel pair with bright beaded edge, mohair lined channel, die trimmed and round formed at the top. Sold in 29" pairs.
Front Bumper Grommet
p/n: 70-0291-28
Grommets, front bumper arm. Hollow construction for good fit. Fully molded rubber.
Chrome Fender Welting - 50ft
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Fender Welting 1/4" Bead - 50ft
p/n: 70-1098-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body.
Fender Welting with 3/16" Bead - 50ft
p/n: 70-1100-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching four (4) fenders to body. Sold in a 50 foot roll.
Fender Skirt Edge Weatherstrips
p/n: 70-0055-45
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish and sealing function. Two five (5) foot strips that fit between the rear wheel fender skirt and rear quarter panel.
Front Stabilizer Bushing
p/n: 70-0348-33
Bushings, front stabilizer bar mounting. Fully molded rubber. One and thirteen sixteenths inch (1 13/16") length by one and three eighths inch (1 3/8") width by eleven sixteenths inch (11/16") inside hole diameter by one and one half inch (1 1/2") height.
Windshield Division Bar Gasket
p/n: 70-0277-51
This inner and outer Windshield Division Bar Gasket is designed from the original part for superior fitment and function. This windshield center divider is molded with pilots and screw holes. Without a steel core.
Fender Skirt Edge Weatherstrip
p/n: 20-0111-44
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish and sealing function. Two five (5) foot strips that fit between the rear wheel fender skirt and rear quarter panel.
Fuel Neck Grommet
p/n: 70-0090-39
Grommet, fuel filler neck. Off center flange style. Fully molded rubber.
Trunk Bumper
p/n: 50-0163-87
Bumper, trunk. Brass core, screw held. Two (2) per car.Length: 1.5 inches. Width: .75 inches.
1935-1974 Cadillac Factory Parts Manual, CD
p/n: 07-1346-07
This GM Licensed Detroit Iron CD provides the most comprehensive set of digital Cadillac Factory parts manuals. The factory manuals on this CD were professionally scanned from the original service and parts manuals.
Accelerator Pedal Pad
p/n: 70-0275-40
Pad, accelerator pedal, full slipover type, fits over old metal after removing original rubber. Length: 8.5 inches.
Rigid Run Channels
p/n: 70-0347-58
This Rigid Run Channel pair is stainless beaded and mohair-lined to help eliminate window rattles and provide a smooth sliding surface for glass movement. Also works to protect the glass.
Flexible Run Channel
p/n: 70-1239-58
This Flexible Run Channel provides a smooth sliding surface while helping to eliminate rattle and protect the glass. The run channel has the stainless beaded edge and is cloth covered and mohair lined with the flexible metal channel.
Vent Division Bar Weatherstrip
p/n: 70-0800-56
This Front Vent Division Bar Weatherstrip is fully molded with metal core and attaching tabs.
Window Felt Beltline Weatherstrips
p/n: 70-0555-58
These Window Felt Beltline Weatherstrips are sold as a three (3) foot pair. The beltline is used for side windows inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Brake and clutch shank seal
p/n: 70-0192-23
Grommets, clutch and brake pedal shank. Hollow accordion action type, not a sponge ring.
Flexible Run Channel
p/n: 70-1238-58
Cloth covered, mohair lined flexible metal channel for sides and top of door windows.
Chrome Fender Welting - 25ft
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Fender Welting 1/4" Bead - 25ft
p/n: 70-1097-44
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty-five (25) foot roll. Typically used to attach two (2) fenders to body.
Sliding Quarter Window Weatherstrip
p/n: 70-0353-78
This Sliding Quarter Window Weatherstrip is used for side window inner and/or outer, front and/or rear doors. Available in a 6ft. lengths.
Fender Welting with 3/16 Bead - 25ft
p/n: 70-1099-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching two (2) fenders to body. Sold in a 25 foot roll.
Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
Cowl vent weatherstrip
p/n: 70-0143-54
Gasket, cowl vent. Perfect copy of original, not a sponge substitute, top quality material.
2-3/8" Firewall Grommet
p/n: 70-0350-20
This Firewall Grommet is used to run the coil wire thermometer tube through the firewall. Designed from the original part for superior fit and seal.
2-7/16" Firewall Grommet
p/n: 70-0622-20
This Firewall Grommet is used to run the wiring harness, oil pressure tube, windshield wiper tube, capillary tube, and radio antenna wire through the firewall. Designed from the original part for superior fit and seal.
2-7/16" Firewall Grommet
p/n: 70-0621-20
This Firewall Grommet is used to run the cowl vent drain hose and throttle control cable through the firewall. Designed from the original part for superior fit and seal.
Exhaust System Hanger
p/n: 70-0626-13
Insulator (hanger) tailpipe to frame. See also our #70-0600-13.Length: 3.9375 inches. Width: 1.9375 inches.
Firewall Grommet
p/n: 70-1203-20
This Firewall Grommet is used to run various electrical and dash gauge wires through the firewall. Also see our 32-1201-20 and 32-0225-20.
Exhaust system hanger
p/n: 70-0220-13
Insulator, exhaust system. Double end threaded, for muffler pipe and intermediate pipe bracket on extra long body styles. Two (2) required per car.
Windshield Division Bar Gasket
p/n: 70-0098-52
This Windshield Division Bar Gasket is designed from the original part for superior fitment and seal. Part combines inner and outer gasket in one piece as original. For seventeen (17") inch to (20") inch lengths.
Rear Spring Pad
p/n: 70-0191-32
Pad, rear spring insulator for two (2) inch wide springs. (see our number 70-0245-32 for two and one fourth (2-1/4) inch springs). Cloth reinforced. Four (4) per vehicle.
Spare Tire Bumper
p/n: 70-0126-37
Rest pad, spare wheel cover, metal core, screw held type. Eight (8) required per car.Width: 1.75 inches. Height: 1.4375 inches.
Hood Rest Pad
p/n: 70-0150-42
Pad, hood rest, molded to brass core, screw mounted.Width: 1.75 inches.
Spare Tire Bumper
p/n: 70-0125-37
Rest pad, spare wheel cover, metal core, tab held type. Sixteen (16) required per car.Width: 1.75 inches. Height: .75 inches.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Door Handle Ferrule
p/n: 60-0389-69
Ferrule, outside door handle. Chrome with rubber sleeve. Two (2) piece set includes one (1) chrome piece and one (1) rubber piece. Enough for one door.
2" Firewall Grommet
p/n: 70-0158-21
This Firewall Grommet is used to run the ignition switch conduit through the firewall. Designed from original parts for excellent workmanship.
Body Mounting Pad
p/n: 70-0235-48
Pad, body mounting. Fully molded rubber with locating collar. Rectangular shaped.
Lower Suspension Arm Dust Seal
p/n: 70-0624-32
Dust seal, "O" ring. Lower suspension arm pin bushing. Four (4) required per car.Height: .25 inches.
Wiper Transmission Gasket
p/n: 70-1198-53
Gasket, windshield wiper transmission (1939-later type). Replaces #4097038.
Door Check Link Rod End Stop
p/n: 70-0326-70
End stop and pad, door check link rod. Rubber with embedded steel plate, five sixteenths (5/16) inch diameter thread. Most models with rod type door checks.
Wiper Transmission Gasket
p/n: 70-0499-53
Gasket, wiper transmission mounting. Replaces #4089635 for smaller type wiper gear, about 7/8" X 1-1/8". Early series models only.
Shock or Stabilizer Link Cross Pin Bushing
p/n: 50-0220-32
This Shock or Stabilizer Link Cross Pin Bushing is designed from the original part for superior fitment and function. A rubber bushing for shock absorber link cross pin or stabilizer cross link pin.
Dimmer Switch Grommet
p/n: 40-0083-88
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
Electrical Terminal Boot
p/n: 30-0279-41
This Electrical Terminal Boot is designed from the original part for superior fitment and seal. This boot works to cover and protect electrical terminal connections.
Body Mounting Pad
p/n: 50-0131-48
Pad, body mounting. Fully molded rubber with locating collar. Two-inch (2") square by thirteen sixteenths inch (13/16") locating collar outside diameter by one half inch (1/2") locating collar inside diameter.
Shift Lever Grommet
p/n: 70-0769-26
Grommet, upper shift lever at steering column.Height: .25 inches.