Dimmer Switch Grommet
p/n: 40-0083-88
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
Clutch and Brake Pedal Bump Stops
p/n: 70-4805-24
This Clutch and Brake Pedal Bump Stop pair is designed from the original part for superior fitment, finish and function. These rubber bumpers help align your brake and clutch pedals in the correct position, while also preventing rattles and squeaks.
Vent Window Division Post Weatherstrip
p/n: 70-0040-56
This Vent Window Division Post Weatherstrip is an extruded thirty (30") inch rubber strip that may have to be glued to your old original division post seal core, or directly to the division post.
Exhaust Tailpipe Hanger Strap
p/n: 60-0308-13
This Exhaust Tailpipe Hanger Strap is made from high-quality rubber for a precise, factory like fit for your classic vehicle. Muffler/tailpipe system, reproduction strap type is manufactured to OEM specifications.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Quarter Window Vertical Leading Edge
p/n: 70-0141-58
This quarter to side window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. Slides into metal retaining channel attached to rear side window and seals between the front door window and the rear quarter window.
Brake Master Cylinder Push Rod Boot
p/n: 60-0180-24
This Brake Master Cylinder Push Rod Boot is made from high-quality Nitrile rubber for a precise, factory like fit for your classic vehicle. Manufactured to OEM specifications to install for an authentic fit and finish.
Stabilizer Bar End Link Set
p/n: 60-0221-33
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt 3/8"-16 NF x 6-15/16" long. Comes with metal sleeve, metal cup washers and rubber grommets.
1-7/16" Firewall Grommet
p/n: 60-0276-45
This Firewall Grommet is used to run the throttle rod and tube, oil pressure gauge pipe, heat indicator tube, and choke rod through the firewall.
Brake and Clutch Pedal Pads
p/n: 60-0300-22
Pad, brake and clutch pedal.Length: 3.0 inches. Width: 2.5625 inches.
Lock Pillar Water Deflector
p/n: 70-3635-62
Door panel water deflector, at lock. Fully molded for both left and right hand sides.
Steering Column Seal
p/n: 60-0518-36
Seal, steering column and shift column toe pan. Five eighths (5/8) inch thick sponge rubber.Width: 4.875 inches. Height: .625 inches.
Brake and Clutch Pedal Bumpers
p/n: 60-0104-24
Bumpers, brake and clutch pedal shank, rides under floorboard. One and one eighth (1-1/8) inch clearance for pedal shaft. Compare with part 60-0579-24.
Steering Column Connecting Rod Seal
p/n: 60-0400-36
Steering column steering connecting rod seal. Power steering models require one (1) per car. Non-power steering models require two (2) per car.
Firewall Grommet
p/n: 60-0565-20
This Firewall Grommet is used to run the top hydraulic lines, wiring harness, and speedometer cable through the firewall. Designed from the original part for superior fit, finish and appearance.
Exhaust System Hanger
p/n: 60-0307-13
This Exhaust System Hanger is used for the muffler-to-tailpipe support (insulator) with reinforced webbing. Fully molded from top-quality EPDM dense rubber to ensure durability. One (1) required per car.
Hood To Cowl Weatherstrip
p/n: 70-1698-43
This Hood To Cowl Weatherstrip mounts at the rear of the engine bay to seal between the hood and vehicle body cowl. A reproduction designed from original part so it fits correctly.
Roof Rail Filler
p/n: 70-3644-73
Filler, side roof rail. Front corner, just in front of flipper seal. Right and left, solid brass core, molded screw holes.
Gravel Shield Bumper Set
p/n: 60-0146-30
This Gravel Shield Bumper Set is used as a rear bumper deflector. Also used between the radiator grille and the lower panel. Two (2) required per car. Designed from the original part for superior fitment and seal.
Accelerator Pedal
p/n: 60-0240-40
This reproduction Accelerator Pedal replaces worn or broken originals. Manufactured in quality black rubber. Steel core with hinge. Length: 8-15/16 inches.
Rigid Run Channels
p/n: 70-0516-58
This Rigid Run Channel pair is zinc plated steel with black cloth inside lining to provide a smooth sliding surface for glass movement. Also works to protect the glass. Fastens in place by small screws or rivets on top and bottom.
Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
Rear Bumper Gravel Shield
p/n: 60-0173-30
This Rear Bumper Gravel Shield, also known as a rear bumper face bar-to-body seal, is made of high quality dense rubber. Fully molded rubber with all original features.
Headlight Mounting Pad
p/n: 70-0201-14
This Headlight Mounting Pad is designed from the original part for superior fitment and seal. This pad acts as the headlight adjusting collar. Sold as a pair.
Front Stabilizer Bushing
p/n: 60-0088-34
This Front Stabilizer Bushing pair is fully molded from EPDM dense rubber to ensure durability. Used to connect the stabilizer bar to the vehicle frame. Two (2) required per car.
Suspension Bumper - Front Lower Control Arm
p/n: 50-0092-32
This Suspension Bumper is designed from the original part for superior fitment and function. Bumper mounts to the front suspension lower control arm. Two (2) per car required.
Fender Skirt Edge Weatherstrip
p/n: 60-0109-45
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish, and seal. This weatherstrips fits between the rear wheel fender skirt and the rear fender quarter panel.
Sliding Quarter Window Weatherstrip
p/n: 70-0353-78
This Sliding Quarter Window Weatherstrip is used for side window inner and/or outer, front and/or rear doors. Available in a 6ft. lengths.
Rear spring bushing
p/n: 60-0311-35
Bushing, rear spring front eye, inlox cartridge type as original.
Running Board or Inner Fender Splash Filler
p/n: 60-0288-45
This eight (8) foot Splash Filler strip is used for the running board apron to body or fender splash panels anti-rattle filler. This filler strip is top-quality EPDM sponge rubber to accept rivets or retaining screws.
Window Felt Beltline Weatherstrips
p/n: 70-0555-58
These Window Felt Beltline Weatherstrips are sold as a three (3) foot pair. The beltline is used for side windows inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Headlight Door To Lens Weatherstrips
p/n: 70-0493-14
This Headlight Door To Lens Weatherstrip pair is the double lip type for sealed beam headlights. The pair is molded without wire. Designed from the original part to fit correctly.
Rigid Run Channels
p/n: 70-0347-58
This Rigid Run Channel pair is stainless beaded and mohair-lined to help eliminate window rattles and provide a smooth sliding surface for glass movement. Also works to protect the glass.
Side Window Vent Frame Upper Bumpers
p/n: 60-0183-62
These Side Window Vent Frame Upper Bumpers (pair) are designed from the original part for superior fitment and function. This glass bumper fits in vent frame at the top on the right and left sides of the vehicle.
Brake Master Cylinder Filler Access Hole Cover
p/n: 60-0016-24
This Master Cylinder Access Hole Cover is designed from the original part for superior fitment and seal. Secures the Brake Master Cylinder Filler and Inspection Access Hole in the vehicle.
Front Spring Rubber Bumpers
p/n: 70-0329-32
This Front Spring Rubber Bumper Pair fits to the upper control arms on frame. Manufactured to OEM specifications to install for an authentic fit, finish and function.
Exhaust System Support Pad
p/n: 60-0319-13
This Exhaust System Support Pad is the right-angle type insulator and fabric reinforced. Molded with a steel core at one end as original style.
Door Bumper
p/n: 70-0168-71
Bumper, door side. Square type held by four (4) screws, metal core as original.
Steering Column Floorplate Gasket
p/n: 60-0395-36
This Steering Column Floorplate Gasket is designed from the original part for superior fitment and seal. Cover (grommet), steering gear-to-toe board seal. Width: 5-13/16" inches. Height: 6" inches.
Trunk Weatherstrip Corners
p/n: 60-0511-85
These trunk weatherstrip corners are designed from the original part for superior fitment and seal. The seals mount to the front corners of the trunk directly to the body.
Trunk Weatherstrip Set
p/n: 70-0871-84
This Trunk Weatherstrip Set is designed from original parts for superior fitment and seal. The set contains the strips and corners that mount to the body and the strip that mounts to the decklid.
Rear Window Gasket
p/n: 60-0215-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rear Spring Bumper Service
p/n: 60-0425-32
Bumpers, rear springs to frame. Revulcanization service only.Length: 3.0 inches. Width: 2.5 inches.
Windshield Gasket
p/n: 60-0222-50
This Windshield Gasket mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends. It also has the slot to accommodate the outer edge's decorative molding.
Spring seat service
p/n: 60-0619-35
Seat, rear spring. Revulcanization service only. Send in complete casting with metal sleeve bushing.
Front Door Weatherstrips
p/n: 60-0606-72
This Front Door Weatherstrip pair is designed from the original part for superior fitment and seal. These primary door weatherstrips mount (glue-on) directly to the left and right doors sealing the doors against the vehicle body when the door is closed.
Transmission Mount Service
p/n: 60-0468-25
Support retainer, transmission mounting at front cross member. One (1) required per car. Revulcanization service only.
Front Door Vent Window Weatherstrips
p/n: 38-0052-55
This Front Door Vent Window Weatherstrip set contains the main seals for the vent windows and the base extension pieces for the frame. They are designed and molded from original parts for superior fitment and seal.