Front Door weatherstrip
p/n: 90-0117-72
Door edge weatherstrip (1951-2nd type). This kit is the primary door to body weatherstrip. It includes the seals for the top and sides, the bottom of the door with molded ends and the bellows seal. Adhesive is not included in the kit. Note:
Windshield Gasket
p/n: 70-0590-50
This Windshield Gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit. It also has molded sections for the wiper transmissions and the slot to accommodate the outer edge's decorative molding.
Window Felt and Run Channel Set
p/n: 90-0141-58
This ten (10) piece Window Felt and Run Channel set includes the inner and outer window felts, upper and lower rigid run channels, and flexible run channels needed to complete two (2) doors.
Rear Door Weatherstrip Set
p/n: 90-0119-72
These primary Rear Door Weatherstrips mount (glue-on) directly to the left and right rear doors sealing the full perimeter of the doors against the vehicle body when the door is closed. Includes the Lower Hinge Pillar Weatherstrips.
Front Door Vent Window Set
p/n: 90-0393-90
This front door vent window weatherstrip set is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Rear Window Gasket
p/n: 70-0693-81
This Rear Window Gasket mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
Door Weatherstrip
p/n: 70-0550-73
Weatherstrip, door bottom (1951-2nd type). Molded left and right, overall length forty (40) inches.
Door Weatherstrip
p/n: 70-0738-73
Weatherstrip, front door. Includes molded end and extruded strip from inner end to bottom edge. With brass screw retainer as original.Length: 98.0 inches.
Front Door Vent Window Weatherstrips
p/n: 38-0049-55
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Axle Rebound Pad
p/n: 50-0371-35
Bumper, rear axle. Revulcanization service only.Height: 3.5 inches.
Engine Mount Service – Revulcanization Only
p/n: 50-0274-11
This Revulcanization Service Only is designed to restore your Front Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Taillight Mounting Pad
p/n: 50-0362-15
Pad, taillight bodies to fender. Correct molded part with correct beading. Four (4) required per car.
Trunk Weatherstrip Set
p/n: 70-0871-84
This Trunk Weatherstrip Set is designed from original parts for superior fitment and seal. The set contains the strips and corners that mount to the body and the strip that mounts to the decklid.
Transmission Mount Service
p/n: 50-0264-25
Support pad, transmission mount (insulator). Revulcanization service only.Length: 5.0 inches. Width: 2.0 inches.
Transmission Mount Service
p/n: 50-0263-25
Support, transmission (insulator). Revulcanization service only. See also our #50-0262-25, many models use both.Length: 5.0 inches. Width: 1.875 inches.
Transmission Mount Service
p/n: 50-0262-25
Pad, transmission mounting, thrust. Revulcanization service only. One (1) per car required. See also our #50-0263-25. Many models use both.Length: 7.
Torque ball service
p/n: 50-0190-27
Retainer, torque ball, heavy steel jacket with molded rubber inner collar. Revulcanization service only.
Taillight wiring boot
p/n: 50-0419-15
Boot, taillight and turn signal wiring. Excellent quality tubing with correct molded ends. Overall length 10". Two (2) pair required per car.
Door Weatherstrip Hinge Pillar
p/n: 50-0268-73
Weatherstrip, body hinge pillar to door, bellows type seal.
Rigid Run Channels
p/n: 70-0536-58
A Rigid Run Channel pair with bright beaded edge, mohair lined channel, die trimmed and round formed at the top. Sold in 29" pairs.
Axle Rebound Pad
p/n: 50-0370-35
Bumper, rear axle stop. Molded left and right. Revulcanization service only.
Chrome Fender Welting - 50ft
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Trunk Weatherstrip Corners
p/n: 60-0511-85
These trunk weatherstrip corners are designed from the original part for superior fitment and seal. The seals mount to the front corners of the trunk directly to the body.
Hood to Cowl Weatherstrip
p/n: 70-0497-43
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This seal mounts at the rear of the engine bay to seal between the hood and vehicle body cowl.
Stabilizer Bar End Link Set
p/n: 70-0567-34
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt. 5/16"-24NF x 7-5/8" long. Includes metal sleeves, cup washers and rubber grommets.
Rear coil spring pad
p/n: 50-0359-35
Insulators, rear coil spring. Fabric reinforced rubber as original. One (1) pair per car.
Side Window Vent Frame Upper Bumpers
p/n: 60-0183-62
These Side Window Vent Frame Upper Bumpers (pair) are designed from the original part for superior fitment and function. This glass bumper fits in vent frame at the top on the right and left sides of the vehicle.
Taillight Gasket
p/n: 50-0355-15
Gasket, rear stop and turn signal. Four (4) piece set required per car.
Rigid Run Channels
p/n: 70-0347-58
This Rigid Run Channel pair is stainless beaded and mohair-lined to help eliminate window rattles and provide a smooth sliding surface for glass movement. Also works to protect the glass.
Flexible Run Channel
p/n: 70-1239-58
This Flexible Run Channel provides a smooth sliding surface while helping to eliminate rattle and protect the glass. The run channel has the stainless beaded edge and is cloth covered and mohair lined with the flexible metal channel.
Window Felt Beltline Weatherstrips
p/n: 70-0555-58
These Window Felt Beltline Weatherstrips are sold as a three (3) foot pair. The beltline is used for side windows inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Headlight Door To Lens Ring Seals
p/n: 70-0389-14
This Headlight Door To Lens Ring seal pair is designed from the original part for superior fitment and function. The part works to seal between the headlight door housing and the headlight retaining ring. The part is a single lip type seal for sealed beam headlights.
Front Stabilizer Bushing
p/n: 50-0094-34
Bushings, front stabilizer shaft-to-frame or stabilizer shaft, front or rear. Fully molded rubber.
Clutch and Brake Pedal Pads - Brown
p/n: 50-0054-89
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality brown rubber.
Flexible Run Channel
p/n: 70-1238-58
Cloth covered, mohair lined flexible metal channel for sides and top of door windows.
Chrome Fender Welting - 25ft
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Sliding Quarter Window Weatherstrip
p/n: 70-0353-78
This Sliding Quarter Window Weatherstrip is used for side window inner and/or outer, front and/or rear doors. Available in a 6ft. lengths.
Door Weatherstrip
p/n: 50-0219-73
This Door Weatherstrip is made of a high-quality sponge extrusion to original configuration. This weatherstrip is for the front door opening, lower front body hinge pillar.
Suspension Bumper - Front Lower Control Arm
p/n: 50-0092-32
This Suspension Bumper is designed from the original part for superior fitment and function. Bumper mounts to the front suspension lower control arm. Two (2) per car required.
Parking and Signal Gasket
p/n: 50-0354-16
Gasket, front parking and signal light to fender. One (1) pair per car. Fits between signal lamp body and headlamp to fender adapter.Width: 4.0 inches.
Heater control valve seal
p/n: 50-0347-20
Seal, heater control valve. High quality sponge rubber designed to cushion heater control valve and keep out noise and water.
Headlight Mounting Pad
p/n: 70-0201-14
This Headlight Mounting Pad is designed from the original part for superior fitment and seal. This pad acts as the headlight adjusting collar. Sold as a pair.
Parking Light Lens Gasket
p/n: 50-0351-16
Gasket, headlight door parking lens. Constructed out of soft durable rubber.Height: .375 inches.
Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
Brake Pedal Pad
p/n: 50-0349-22
This reproduction Pedal Pad slips over the full perimeter of the brake pedal for a precise, factory fit. For models with Power Brakes.
Rigid Run Channels
p/n: 70-0516-58
This Rigid Run Channel pair is zinc plated steel with black cloth inside lining to provide a smooth sliding surface for glass movement. Also works to protect the glass. Fastens in place by small screws or rivets on top and bottom.
Brake and Clutch Shank Seal
p/n: 50-0066-24
Grommet, brake and clutch pedal floor seal.Width: 1.8125 inches. Height: 2.375 inches.
Parking Light Lens Gasket
p/n: 50-0353-16
Gasket, front parking lens. High quality sponge rubber better than original. One (1) pair per car.Width: 3.375 inches. Height: 2.625 inches.
Parking Brake Pedal Pad
p/n: 50-0348-22
Pad, parking brake pedal. Without "PARK" written on pad. Black only. For pedal pad with "PARK" written on pad see our #50-0405-22.Height: 2.0 inches.
Clutch and Brake Pedal Pads - Black
p/n: 50-0054-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Front coil spring pad
p/n: 50-0358-35
Insulators, front coil spring. Fabric reinforced rubber as original.
Reflector gasket
p/n: 50-0360-15
Seal, reflector signal, between taillights. With correct slits for tabs on reflector. One (1) pair required per car.
Wiring grommet
p/n: 50-0346-21
Grommet, spark plug wire. Trapezoidal style under spark plug cover flange at right end of both sides. One (1) pair required per car with our #50-0345-21.
Wiring grommet
p/n: 50-0345-21
Grommet, spark plug wire. Oblong style for spark plug wire clip at right rear of head. One (1) pair required per car with our #50-0346-21.Width: 1.
Brake Pedal Pad - Dyna-Flow Transmission
p/n: 50-0285-22
This reproduction Pedal Pad slips over the full perimeter of the brake pedal for a precise, factory fit. For models with Dyna-Flow and standard brakes.
Heater control valve seal
p/n: 50-0356-20
Seal, heater control valve. High quality sponge rubber designed to cushion heater control valve and keep out noise and water. For all except right-hand drive.
Trunk Bumper
p/n: 70-0296-87
T-nut, trunk bumper in gutter at sides, brass core tapped 10-32 thread. Two (2) required per car. For models having partial weatherstrip in gutter of body.
Body Mounting Pad
p/n: 50-0477-48
Pad, body mounting. Fully molded rubber with metal core & locating collar.
Door Handle Gasket Set
p/n: 50-0322-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Hydraulic Pump Mounting Cushion
p/n: 70-0852-67
This Hydraulic Pump Mounting Cushion is designed from the original part for superior fitment and function. Used on models with hydraulic window lifts or a hydraulic convertible top. Two (2) to three (3) required per car.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Hood Bumper
p/n: 50-0159-42
Bumper, hood ledge corner at shroud.Width: 1.25 inches. Height: .5 inches.
Rear coil spring pad
p/n: 50-0304-35
Insulator, rear coil spring clamp bolt (upper end). Two (2) per car. Fabric reinforced rubber as original.
Body Mounting Pad
p/n: 50-0096-48
Pad, body mounting. Fully molded rubber with steel core and locating collar.
Parking, Signal or Backup Light Lens Gaskets
p/n: 50-0381-16
This front Parking and Turn Signal Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Light Lens and the Light Housing or Bezel. Also fits Backup Light Lens on cars with optional Backup Lights.
Vent Window Division Post Weatherstrip
p/n: 70-0040-56
This Vent Window Division Post Weatherstrip is an extruded thirty (30") inch rubber strip that may have to be glued to your old original division post seal core, or directly to the division post.
Clutch and Brake Pedal Bump Stops
p/n: 70-4805-24
This Clutch and Brake Pedal Bump Stop pair is designed from the original part for superior fitment, finish and function. These rubber bumpers help align your brake and clutch pedals in the correct position, while also preventing rattles and squeaks.
Dimmer Switch Grommet
p/n: 40-0083-88
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
1-5/8" Firewall Grommet
p/n: 50-0364-20
This Firewall Grommet is used to run the oil pressure and water temperature, or washer vacuum hose through the firewall. Designed from original part for excellent workmanship.
License lens gasket
p/n: 50-0357-17
Gasket set, rear license light assembly. One (1) rubber ring and one (1) cork rubber gasket comprise set.
Body Mounting Pad
p/n: 50-0097-48
Pad, several usages. Use as a body mounting pad or as a cushion for body mounting bolt. Fully molded rubber. Up to twenty (20) required per car.
1-5/8" Firewall Grommet
p/n: 50-0363-20
This Firewall Grommet is used to run the windshield washer hose through the firewall. Designed from original part for excellent workmanship.
Axle Rebound Pad
p/n: 50-0302-35
Bushing, rear axle, anti-sway rod ends. Fully molded rubber. Four (4) required per car.
Hood Bumper
p/n: 50-0490-42
Bumper, hood to fender. Uses four (4) per car for most models.Width: 1.375 inches. Height: 1.25 inches.
Window Stop Stem Bumper
p/n: 33-0540-62
This Window Stop Stem Bumper is fully molded and designed from the original part for superior fitment and seal. Designed as a window stop cushion for front and rear door, rear side and quarter windows as required.
Glovebox Link Bumper
p/n: 50-0367-88
This Glovebox Link Bumper is made to original specifications for an authentic fit and appearance. The glovebox check link bumper fits on the glovebox door arm.
Shift Lever Grommet
p/n: 50-0284-24
Grommet, shift lever insulator. One (1) per car. Three eighths (3/8) inch inside diameter by five eighths (5/8) inch barrel by one half (1/2) inch long.
Side Window Roller
p/n: 70-0117-62
This Side Window Roller, anti-rattle roller, is manufactured using EPDM dense rubber to replace the original perfectly. The roller fits both styles of brackets.
Brown Door Lock Knob
p/n: 70-0660-70
This is the Knob or push button for the inside door lock. The part fits over 1/8" steel rod to door lock. Neutral brown color that may be lacquered with other colors as required. A hard rubber part fits many different vehicles.
3/4" Trunk Weatherstrip
p/n: 70-0463-85
This Trunk Weatherstrip is made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
Starter Solenoid Cable Rubber Boot
p/n: 70-0704-21
This Starter Solenoid Cable Rubber Boot is designed from the original part for superior fitment and function. This boot covers and protects the battery cable at the starter solenoid connection.
11/16" Door Weatherstrip
p/n: 70-0491-73
This Door Weatherstrip for the side window is made of an extruded sponge rubber. The weatherstrip is the larger type that is used on most GM cars this period. Available by the foot.
Shock and Stabilizer Grommet
p/n: 70-0274-33
This Shock and Stabilizer Grommet is fully molded using EPDM dense rubber. Designed from original with locating collar. Eight (8) required per car.
9/16" Trunk Weatherstrip
p/n: 60-0411-85
This Trunk Weatherstrip is made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
13/16" Trunk Weatherstrip
p/n: 50-0161-85
This Trunk Weatherstrip was designed from an original part for a specific application but has many uses outside of its original purpose. Available by the foot.
Vacuum Pump Mounting Cushion
p/n: 70-1571-24
Mounting cushion, vacuum pump. Three (3) per car required.Width: .625 inches.
Pressure Ring
p/n: 70-0261-69
Pressure ring (washer), sponge rubber, interior door handle and window regulator escutcheon. One and three fourths (1-3/4) inches outside diameter by three eighths (3/8) inch thick.
Lock Cylinder Gasket
p/n: 70-0955-86
Gasket, trunk lock cylinder. Steel rule die cut from one thirty seconds (1/32) inch dense rubber.
2-1/4" Body Hole Plug
p/n: 35-0863-45
This Body Hole Plug is fully molded and designed from the original part for superior fitment and seal. Designed for the trunk, however the generic shape makes this plug usable for a variety of applications.