Rear Door Weatherstrip Set
p/n: 90-0110-72
This rear door edge weatherstrip set is designed from the original parts for superior fitment and seal. These primary door to body weatherstrip seals mount directly to the full perimeter of both the left and right rear doors to seal against the body.
Door Weatherstrip Set
p/n: 90-0109-72
This Door Weatherstrip Set is the primary door to body weatherstrip. This set includes the weatherstrip for the door opening, sides and the top and bottom a bottom weatherstrips which is held by metal track or clips.
Window Felt and Run Channel Set
p/n: 90-0141-58
This ten (10) piece Window Felt and Run Channel set includes the inner and outer window felts, upper and lower rigid run channels, and flexible run channels needed to complete two (2) doors.
Door - Upper Weatherstrip
p/n: 70-0063-73
Door - Upper Weatherstrip - The upper and inner door weatherstrip on the body. Hollow rubber seal, fits metal retainer as original. Set of four (4) strips, five (5) foot long per strip.
Front Door Opening Weatherstrip
p/n: 50-0155-73
This Front Door Opening Weatherstrip set is designed from the original parts for superior fitment and seal. These door edge seals mount (glue-on) directly to the left and right front doors sealing the front edge opening of the door against the vehicle body when the door is closed.
Door opening step pad
p/n: 70-0594-49
Matting, cover panel extension, fender to door, front, right and left, with brass core, as original.
Front Door Vent Window Set
p/n: 90-0386-90
This front door vent window weatherstrip set is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Windshield Gasket
p/n: 50-0175-50
This Windshield Gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit.
Window Felt and Run Channel Set
p/n: 90-0142-58
This six (6) piece Window Felt and Run Channel set includes the inner and outer window felts and the flexible run channels needed to complete two (2) doors. This set is used for front or rear doors in models without vent windows in the door.
Hood to Cowl Weatherstrip
p/n: 70-1209-42
Weatherstrip, hood to cowl. To facilitate manufacturing, some may be made in two sections.
Engine Mount Service – Revulcanization Only
p/n: 70-0529-11
This Revulcanization Service Only is designed to restore your Front Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Door opening step pad
p/n: 70-0593-49
Matting, cover panel extension, fender to door, rear, right and left, with brass core as original.
Front Fender Dust Shield Seal
p/n: 70-0581-45
This Front Fender Dust Shield works as a shield to radiator air deflector. Sold as a pair for the right and left side.
Rear door vent weatherstrip
p/n: 38-0042-74
Weatherstrip, rear door vent. For Buick vehicles order our #50-0464-74 division post weatherstrip separately. For Cadillac vehicles order our #70-0040-56 division post seal separately. For Oldsmobile vehicles order our #50-0317-56 division post seal separ
Front Door Vent Window Weatherstrips
p/n: 38-0041-55
These Front Door Vent Window Weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Taillight Mounting Pad
p/n: 70-0471-15
Pads, taillight body to fender, right and left. Also order #70-0658-15 for the taillight lens gasket, and for the taillight gasket order #70-0900-15.
Fog Light Gasket
p/n: 70-0606-17
Gasket, fog light mounting to fender, sponge rubber, right and left.Length: 9.25 inches. Width: 5.5 inches.
Engine Mount Service – Revulcanization Only
p/n: 70-0629-11
This Revulcanization Service Only is designed to restore your Rear Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Trunk Weatherstrip
p/n: 70-0872-84
This Trunk Weatherstrip set is designed from original parts for superior fitment and seal. The seals mount directly to the body and cover the full perimeter of the trunk.
Front Stablizer Bar End Link Kit
p/n: 70-0574-33
Kit, front stabilizer bar link assembly replacement. Twenty two (22) piece set for both sides of one (1) car. Hex head bolt. 3/8"-16nc x 8-7/8" lg. Comes with metal sleeve, metal cup washers and rubber grommets.
Front Spring Bumpers - Lower Suspension Arms
p/n: 70-0172-32
This Front Spring Bumpers pair is designed from the original part for an authentic fit, finish, and appearance. These front spring bumpers install to the lower suspension arms. An original copy reproduction.
Coil spring insulator pad
p/n: 70-0801-32
Pad, coil spring insulator. Molded four (4) piece set for one (1) car.
Rigid Run Channels
p/n: 70-0536-58
A Rigid Run Channel pair with bright beaded edge, mohair lined channel, die trimmed and round formed at the top. Sold in 29" pairs.
Fog Light Gasket
p/n: 70-1242-17
Seal, fog light body. With notches. For seal without notches see our #70-1243-17.Length: 6.5 inches. Width: 7.75 inches.
Fender Welting 1/4" Bead - 50ft
p/n: 70-1098-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body.
Chrome Fender Welting - 50ft
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Fender Welting with 3/16" Bead - 50ft
p/n: 70-1100-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching four (4) fenders to body. Sold in a 50 foot roll.
Brown Accelerator Pedal Pad
p/n: 70-0208-89
Pad, accelerator pedal. Brown rubber. For black see our #70-0208-40. Made to slip over old metal core after removing old rubber.
License Plate Light Lens Gaskets
p/n: 70-0560-17
This License Plate Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the License Plate Light Lens and the License Plate Light Housing or Bezel.
Rear Axle Bumpers
p/n: 70-0210-32
This Rear Axle Bumper pair is a quality reproduction of the original factory part. These bottoming pads are dense rubber blocks that mount by bracket to the rear axle tube.
Fender Skirt Edge Weatherstrip
p/n: 70-0154-45
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish, and seal. This weatherstrips fits between the rear wheel fender skirt and the rear fender quarter panel.
Fender Skirt Edge Weatherstrip
p/n: 70-0289-45
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish, and seal. This weatherstrips fits between the rear wheel fender skirt and the rear fender quarter panel.
Sliding Quarter Window Weatherstrips
p/n: 60-0398-78
These Sliding Quarter Window Weatherstrips mount vertically in vehicle body where leading edge of sliding window fits when closed. Right and Left sides rubber only.
Division Bar Grommet
p/n: 70-0483-62
These Division Bar Grommets are fully molded for the rear door vent divider post (wind deflector). Four (4) piece set.
Clutch or Brake Pedal Pad - Brown
p/n: 70-0176-89
This reproduction Clutch or Brake Pedal Pad slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality brown rubber.
Front Stabilizer Bushing
p/n: 70-0193-33
Bushings, front stabilizer bar. Fully molded rubber. One and five eighths inch (1 5/8") length by one and seven sixteenths inch (1 7/16') width by three fourths inch (3/4") inside hole diameter by one and eleven sixteenths inch (1 11/16") height.
Fuel Neck Grommet
p/n: 70-0599-39
Grommet, fuel filler neck, through rear fender splash panel. Fully molded rubber. Four and five eighths inch (4 5/8") outside diameter by two and three sixteenths inch (2 3/16") inside hole diameter.
Rear Gravel Deflector to Bumper Face Bar
p/n: 70-0462-45
This Rear Gravel Deflector to Bumper Face Bar staples to the gravel deflector. The seal is die cut from dense rubber. Sold as a six (6) foot strip.
Accelerator Pedal Pad
p/n: 70-0208-40
Pad, accelerator pedal. Black rubber. For brown see our #70-0208-89. Made to slip over old metal core after removing old rubber. Length: 8.25 inches.
License Light Mounting Pad
p/n: 70-0559-17
Pad, license light bracket or base mounting. Two (2) per car.
1935-1974 Cadillac Factory Parts Manual, CD
p/n: 07-1346-07
This GM Licensed Detroit Iron CD provides the most comprehensive set of digital Cadillac Factory parts manuals. The factory manuals on this CD were professionally scanned from the original service and parts manuals.
Door - Gravel Shield - Running Board Weatherstrip
p/n: 60-0054-73
This Door - Gravel Shield - Running Board Weatherstrip is a anti-squeak bulb type extrusion with fitment for General Motors vehicles. A twelve (12) foot strip made of high-quality EPDM dense rubber and designed from original parts for superior fitment, finish and function.
Window Pinchweld Seal
p/n: 70-0096-52
This twelve (12) foot Window Pinchweld Seal is designed from the original part for superior fitment and function. The part is used to seal and retain an outer decorative reveal molding. Used with our 70-1192-52.
Rigid Run Channels
p/n: 70-0347-58
This Rigid Run Channel pair is stainless beaded and mohair-lined to help eliminate window rattles and provide a smooth sliding surface for glass movement. Also works to protect the glass.
Flexible Run Channel
p/n: 70-1239-58
This Flexible Run Channel provides a smooth sliding surface while helping to eliminate rattle and protect the glass. The run channel has the stainless beaded edge and is cloth covered and mohair lined with the flexible metal channel.
Window Felt Beltline Weatherstrips
p/n: 70-0555-58
These Window Felt Beltline Weatherstrips are sold as a three (3) foot pair. The beltline is used for side windows inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Clutch or Brake Pedal Pad - Black
p/n: 70-0176-22
This reproduction Clutch or Brake Pedal Pad slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Vent division bar weatherstrip
p/n: 70-0697-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Headlight Door To Lens Ring Seals
p/n: 70-0389-14
This Headlight Door To Lens Ring seal pair is designed from the original part for superior fitment and function. The part works to seal between the headlight door housing and the headlight retaining ring. The part is a single lip type seal for sealed beam headlights.
Flexible Run Channel
p/n: 70-1238-58
Cloth covered, mohair lined flexible metal channel for sides and top of door windows.
Hood bumper
p/n: 70-0543-42
Bumpers, hood to fender. Mounted on hood, rubber with steel core. Replaces Bakelite originals which are not available.
Chrome Fender Welting - 25ft
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Fender Welting 1/4" Bead - 25ft
p/n: 70-1097-44
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty-five (25) foot roll. Typically used to attach two (2) fenders to body.
Sliding Quarter Window Weatherstrip
p/n: 70-0353-78
This Sliding Quarter Window Weatherstrip is used for side window inner and/or outer, front and/or rear doors. Available in a 6ft. lengths.
Fender Welting with 3/16 Bead - 25ft
p/n: 70-1099-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching two (2) fenders to body. Sold in a 25 foot roll.
Door Weatherstrip
p/n: 60-0114-73
Weatherstrip, door bottom, sponge constant section, solid skin surface, superior quality. Sold in six (6) foot strips only.Length: 72.0 inches.
Headlight Mounting Pad
p/n: 70-0201-14
This Headlight Mounting Pad is designed from the original part for superior fitment and seal. This pad acts as the headlight adjusting collar. Sold as a pair.
Brake and clutch shank seal
p/n: 70-0465-23
Grommets, brake and clutch pedal shank below floorboard.
Rigid Run Channels
p/n: 70-0516-58
This Rigid Run Channel pair is zinc plated steel with black cloth inside lining to provide a smooth sliding surface for glass movement. Also works to protect the glass. Fastens in place by small screws or rivets on top and bottom.
Taillight Gasket
p/n: 70-0900-15
Gasket, taillight housing. Also order #70-0471-15 for the taillight mounting pad, and for the taillight lens gasket order #70-0658-15. Length: 8.25 inches.
Door Lock Weatherstrip
p/n: 50-0172-70
Weatherstrip, door lock, front and rear. Protects door lock mechanism from dust and weather.Length: 3.625 inches.
2-3/8" Firewall Grommet
p/n: 70-0185-20
This Firewall Grommet is used to run the main wiring harness in addition to five (5) accessory wires through the firewall. Designed from the original part for superior fit and seal.
Center Division Bar Chrome Molding Retainer
p/n: 70-0373-51
Center Division Bar Chrome Molding Retainer for outside windshield center post stainless molding. Use with original stainless molding and clips. Length: 15-1/2 inches. Width: 1-1/4 inches.
Brake and Clutch Shank Seal
p/n: 70-0962-23
Grommet, brake or clutch shaft at toe board.Height: 1.0 inches.