Gearshift Bushing
p/n: 60-0237-24
This Gearshift Bushing is fully molded and designed from the original part for superior fitment and seal. This bushing is made from high-quality EPDM dense rubber to provide excellent durability. Designed for the gearshift shaft lever, large type.
Glovebox Link Bumper
p/n: 70-1459-88
Bumper, glovebox check link. Fits on glovebox door arm as needed.Length: .75 inches. Width: .3125 inches. Height: .4375 inches.
Headlight Door To Lens Ring Seals
p/n: 70-0389-14
This Headlight Door To Lens Ring seal pair is designed from the original part for superior fitment and function. The part works to seal between the headlight door housing and the headlight retaining ring. The part is a single lip type seal for sealed beam headlights.
Headlight Door To Lens Weatherstrips
p/n: 70-0493-14
This Headlight Door To Lens Weatherstrip pair is the double lip type for sealed beam headlights. The pair is molded without wire. Designed from the original part to fit correctly.
Headlight Mounting Pad
p/n: 70-0201-14
This Headlight Mounting Pad is designed from the original part for superior fitment and seal. This pad acts as the headlight adjusting collar. Sold as a pair.
Hood and Trunk Bumper Cap for Adjustment Screw
p/n: 70-0294-42
This Hood and Trunk Bumper Cap is designed from the original part for superior fitment, finish and function. Cap type for front hood or rear trunk lid adjustment screw.
Hood to Cowl Weatherstrip
p/n: 60-0138-42
This Hood To Cowl Weatherstrip pair installs at the rear of the engine bay to seal between the hood and vehicle body cowl. Sold as a pair for left and right side.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
Parking Light Grommet
p/n: 60-0452-17
Grommet, parking light wiring harness through fender.Length: 3.25 inches.
Parking Light Mounting Pad
p/n: 60-0007-17
Mounting pads, parking lights.Length: 4.25 inches. Width: 2.375 inches.
Peel-N-Stick Door Edge Weatherstrip
p/n: 70-0390-WT
This Peel-N-Stick Door Edge Weatherstrip is designed for a specific set of vehicles but with its generic shape, has many uses outside of its original purpose. Available by the foot. Available by the foot.
Peel-N-Stick Door Weatherstrip
p/n: 70-0145-WT
This Peel-N-Stick Door Weatherstrip is made from a high-quality EPDM sponge rubber. Available by the foot.
Peel-N-Stick Door Weatherstrip
p/n: 70-0331-WT
This Peel-N-Stick Door Weatherstrip is made from high-quality EPDM sponge rubber. Available by the foot.
Pressure Ring
p/n: 70-0261-69
Pressure ring (washer), sponge rubber, interior door handle and window regulator escutcheon. One and three fourths (1-3/4) inches outside diameter by three eighths (3/8) inch thick.
Rear Gravel Deflector to Bumper Seal
p/n: 60-0020-30
This Rear Gravel Deflector to Bumper Seal is made of a high quality EPDM dense rubber extrusion. Designed from the original part so it fits correctly. Sold as a six (6) foot strip.
Rear Spring Bumper Service
p/n: 60-0425-32
Bumpers, rear springs to frame. Revulcanization service only.Length: 3.0 inches. Width: 2.5 inches.
Rear spring bushing
p/n: 60-0311-35
Bushing, rear spring front eye, inlox cartridge type as original.
Rear Window Gasket
p/n: 60-0580-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rigid Run Channels
p/n: 70-0347-58
This Rigid Run Channel pair is stainless beaded and mohair-lined to help eliminate window rattles and provide a smooth sliding surface for glass movement. Also works to protect the glass.
Rigid Run Channels
p/n: 70-0516-58
This Rigid Run Channel pair is zinc plated steel with black cloth inside lining to provide a smooth sliding surface for glass movement. Also works to protect the glass. Fastens in place by small screws or rivets on top and bottom.
Running Board or Inner Fender Splash Filler
p/n: 60-0288-45
This eight (8) foot Splash Filler strip is used for the running board apron to body or fender splash panels anti-rattle filler. This filler strip is top-quality EPDM sponge rubber to accept rivets or retaining screws.
Shock Absorber Bushing
p/n: 70-0541-33
This Shock Absorber Bushing is manufactured with high-quality Nitrile rubber to OEM specifications. The bushing is the single cone style. Designed from original part and made of high-quality Nitrile dense rubber to ensure durability.
Shock Absorber Link Arm Bushing
p/n: 60-0216-33
This Shock Absorber Link Arm Bushing is designed from the original part for superior fitment, finish and function. This bushing is for double acting shock absorber arm links.
Shock and Stabilizer Grommet
p/n: 70-0274-33
This Shock and Stabilizer Grommet is fully molded using EPDM dense rubber. Designed from original with locating collar. Eight (8) required per car.
Shoe Scraper Mounting Pad
p/n: 60-0325-45
Pad, mounting, boot scraper-to-front fender, right and left.Width: 3.25 inches.
Side Window Roller
p/n: 70-0117-62
This Side Window Roller, anti-rattle roller, is manufactured using EPDM dense rubber to replace the original perfectly. The roller fits both styles of brackets.
Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
Sliding Quarter Window Weatherstrip
p/n: 70-0353-78
This Sliding Quarter Window Weatherstrip is used for side window inner and/or outer, front and/or rear doors. Available in a 6ft. lengths.
Spark plug grommet
p/n: 70-1181-21
Grommet, spark plug and coil wire at distributor cap outlets. For seven (7mm) millimeter, later years.
Spark plug grommet
p/n: 70-1180-21
Grommet, spark plug & coil wire at distributor cap outlets. For nine (9mm) millimeter wire, earlier years.
Spark plug retaining ring
p/n: 30-0352-21
Retaining ring, spark plug wire. Two (2) per car.Chevrolet 1935-48 Retaining ring, spark plug wire. Two (2) per car. All models.
Spring seat service
p/n: 60-0619-35
Seat, rear spring. Revulcanization service only. Send in complete casting with metal sleeve bushing.
Spring shackle seal
p/n: 70-1125-33
Washer, front and rear spring shackle, seal for shackle pin. Constructed of neoprene.
Stabilizer Bar End Link Set
p/n: 60-0221-33
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt 3/8"-16 NF x 6-15/16" long. Comes with metal sleeve, metal cup washers and rubber grommets.
Starter Button
p/n: 60-0322-21
Starter button, push on replacement to rod. Two (2) inch outside diameter.
Starter Button Cover
p/n: 60-0166-21
Cover, starter pedal button. Rubber slip over type for old metal. Two (2) inch outside diameter. If car doesn't have old metal, see our #60-0322-21.
Starter Pedal Bellows
p/n: 60-0210-21
Bellows, starter pedal shaft to floorboard. Three eighths (3/8) inch top hole with three (3) inch height.Width: 2.875 inches. Height: 3.0 inches.
Steering Column Gearshift Vacuum Boot
p/n: 60-0555-24
This Steering Column Vacuum Cylinder Boot is designed from the original part for superior fitment, finish and function. An excellent duplicate of original.
Steering Column Grommet - Black
p/n: 60-0621-36
This black rubber Steering Column To Toe Board Grommet is designed from the original part for superior fitment and sealing. Part is molded from quality rubber to authentic original dimensions.
Steering Column Grommet - Brown
p/n: 60-0621-89
This brown rubber Steering Column To Toe Board Grommet is designed from the original part for superior fitment and sealing. Part is molded from quality rubber to authentic original dimensions.
Steering Column Seal
p/n: 60-0419-36
Seal, steering column toe pan. One (1) required per car. Top quality sponge rubber, five eighths (5/8) inch thick.Width: 3.50 inches. Height: .625 inches.
Steering Gear Pitman Arm Bushing
p/n: 60-0105-36
This Steering Gear Pitman Arm Bushing is designed from the original part for superior fitment and function. Fully molded with steel core.
Steering knuckle support seal
p/n: 60-0089-32
Seal, steering knuckle support, upper. Four (4) per car.
Taillight Mounting Pad
p/n: 60-0122-15
Pad, taillight mounting. For high mounted taillights. (This pad was not actually used by factory. NO pad was used under these lights.
Taillight Mounting Pad
p/n: 60-0008-15
Mounting pads, taillight. Length: 6.50 inches. Width: 2.6875 inches.
Transmission Mount Service
p/n: 60-0407-25
Insulator (support), transmission mounting. Revulcanization service only.Length: 7.0625 inches.
Transmission Support Mount - Revulcanization Service Only
p/n: 60-0530-25
Insulator - Plate Assembly - Guide for transmission support bracket. This Revulcanization Service Only is designed to restore your transmission mount to a like new original condition. Please call or email for more service details and ordering.
Vent Window Division Post Weatherstrips
p/n: 60-0569-56
This Front Window Vent Division Post Weatherstrip pair is fully molded with metal core and attaching tabs.
Window Channel Retaining Clip
p/n: 70-0515-62
Clip, side window run channel retaining. Rust resistant spring steel.
Window Channel Retaining Clip
p/n: 70-0514-62
Clip, side window run channel retaining. Rust resistant spring steel. Compare with your original.
Window Felt and Run Channel Set
p/n: 90-0141-58
This ten (10) piece Window Felt and Run Channel set includes the inner and outer window felts, upper and lower rigid run channels, and flexible run channels needed to complete two (2) doors.
Window Felt Beltline Weatherstrips
p/n: 70-0555-58
These Window Felt Beltline Weatherstrips are sold as a three (3) foot pair. The beltline is used for side windows inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Window Pinchweld Seal
p/n: 70-0096-52
This twelve (12) foot Window Pinchweld Seal is designed from the original part for superior fitment and function. The part is used to seal and retain an outer decorative reveal molding. Used with our 70-1192-52.
Window Stop Stem Bumper
p/n: 33-0675-62
Cushion (stem bumper), window stop, lower. For front and rear door, rear side and quarter windows as required.
Windshield Division Bar Gasket
p/n: 70-0098-52
This Windshield Division Bar Gasket is designed from the original part for superior fitment and seal. Part combines inner and outer gasket in one piece as original. For seventeen (17") inch to (20") inch lengths.
Windshield Division Bar Gasket
p/n: 70-0372-51
This Windshield Division Bar Gasket is designed from the original part for superior fitment and seal. Part is properly sized with "H" section. Part requires fitting to top and bottom, as it is not drilled.
Windshield Gasket
p/n: 60-0187-50
This Windshield Gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit.
Windshield Gasket
p/n: 70-1534-50
This Windshield Gasket is for windows without chrome reveal molding or divider bar. Mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.