13/16" Firewall Grommet
p/n: 32-0158-17
This Firewall Grommet is designed from the original part for superior fitment and seal. Designed for firewall applications such as running the hand brake cable through the firewall or the license light through the trunk.
5/16" Glovebox Door Bumper
p/n: 33-0128-88
This 5/16" Glovebox Door Bumper is designed from the original part for superior fitment, finish and function. This bumper is commonly used as a glovebox door bumper on GM models.
5/16" Standard Stem Bumper - GM
p/n: 33-0127-41
This 5/16" Standard Stem Bumper is designed from the original part for superior fitment, finish and function. This bumper is commonly used as a console and fuel filler door bumper on GM models.
1/2" Standard Bumper
p/n: 33-0136-42
This Standard Bumper is fully molded from quality dense rubber to provide excellent durability. Commonly used as a door bumper on the center upper post on post model vehicles.
1-3/8" Wiring Grommet
p/n: 32-0369-20
This Wiring Grommet is fully molded and designed from the original part for superior fitment and seal. Designed to run the wiring harness through the fender skirts or hood latch lower mounting panels.
3/4" Hood and Door Bumper
p/n: 33-0459-42
This Hood and Door Bumper is fully molded and designed from the original part for superior fitment and seal. Designed for hood to cowl and door hinge pillar upper bumper. May be used in both places.
Hood and Trunk Bumper Cap for Adjustment Screw
p/n: 70-0294-42
This Hood and Trunk Bumper Cap is designed from the original part for superior fitment, finish and function. Cap type for front hood or rear trunk lid adjustment screw.
3/4" Trunk Floor Pan Plug
p/n: 35-0070-87
This Trunk Floor Pan Plug is fully molded and designed from the original part for superior fitment and seal. This plug is made from high-quality EPDM dense rubber to provide excellent durability.
9/16" Wiring Grommet
p/n: 32-0352-20
This Wiring Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber. Designed for the parking brake release rod.
3/4" Body Hole Plug
p/n: 35-0369-20
This Floor Plug is fully molded and designed from the original part for superior fitment and seal. Designed for shroud or cowl upper panel gauge holes and for various body holes requiring a plug.
Side Window Lift Limit Cap
p/n: 60-0071-62
Caps, side window lift limit. Rubber, snap-over type, three fourths (3/4) inch diameter by five sixteenths (5/16) inch thick.
Door Bumper
p/n: 33-1227-71
This Door Bumper is fully molded and designed from the original part for superior fitment. The twin retainer style rubber bumper attaches to the vehicle body to support/cushion the door closure. Usually requires two (2) bumpers each per vehicle.
1/4" Universal Mounting Pad
p/n: 70-0308-17
This Universal Mounting Pad is used for lights, hinges, brackets, and other bright work when no molded pad is available. Manufactured with a special edge lip to hug bright work when clamped down. Shape outline to suit application.
1/32" Sash Channel Filler - Rubber
p/n: 70-2169-57
This 1/32" Sash Channel Filler offers the best quality rubber product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
23/32" Firewall Grommet
p/n: 32-0365-20
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber. Designed for firewall applications such as the vent control cable.
1/32" Sash Channel Filler - Cork
p/n: 70-1114-57
This 1/32" Sash Channel Filler offers the best quality cork product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
Door Lock Bumper
p/n: 34-0484-71
This Door Lock Bumper is made from high-quality EPDM dense rubber to provide excellent durability. Designed for applications such as the upper door lock post.
1/16" Sash Channel Filler - Rubber
p/n: 70-2170-57
This 1/16" Sash Channel Filler offers the best quality rubber product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
Door or Tailgate Bumper
p/n: 33-1228-71
This Door Bumper is fully molded and designed from the original part for superior fitment. This rubber bumper attaches to the vehicle body to support / cushion the door closure. Usually requires two (2) bumpers each per vehicle.
Firewall Retainer
p/n: 60-0586-20
This Firewall Retainer is used on the firewall insulation panel. Designed from original for the "Christmas Tree" style popular during this time.
1-5/16" Wiring Grommet
p/n: 32-0439-20
This Wiring Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability.
Gravel Shield Bumper
p/n: 33-0286-30
Bumper, rear gravel shield, anti-rattle. Five (5) or more used per car. Fully molded rubber. Replaces factory #1320392.
1" Floor Pan Grommet
p/n: 35-0515-20
This Floor Pan Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability.
1/16" Sash Channel Filler - Cork
p/n: 70-1115-57
This 1/16" Sash Channel Filler offers the best quality cork product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
1-3/16" Utility Plug
p/n: 35-0099-20
This Utility Plug is fully molded and designed from the original part for superior fitment and seal. This plug is made from high-quality EPDM dense rubber to provide excellent durability.
5/8" Door Weatherstrip
p/n: 70-0219-73
The Door Weatherstrip is designed for 1941-1957 GM and Mopar vehicles but with its generic shape it has many uses outside of its original purpose. Available by the foot.
2-1/4" Body Hole Plug
p/n: 35-0863-45
This Body Hole Plug is fully molded and designed from the original part for superior fitment and seal. Designed for the trunk, however the generic shape makes this plug usable for a variety of applications.
Lock Cylinder Gasket
p/n: 70-0955-86
Gasket, trunk lock cylinder. Steel rule die cut from one thirty seconds (1/32) inch dense rubber.
Pressure Ring
p/n: 70-0261-69
Pressure ring (washer), sponge rubber, interior door handle and window regulator escutcheon. One and three fourths (1-3/4) inches outside diameter by three eighths (3/8) inch thick.
2-5/8" Run Channel Mohair Liner
p/n: 70-2863-58
This Run Channel Mohair Liner helps to reline the guide bars on the lock side of hardtops and convertibles. This mohair liner comes with a rubber backing and installs with adhesive to the division bars and channel. Available by the foot.
Shock and Stabilizer Grommet
p/n: 70-0274-33
This Shock and Stabilizer Grommet is fully molded using EPDM dense rubber. Designed from original with locating collar. Eight (8) required per car.
11/16" Door Weatherstrip
p/n: 70-0491-73
This Door Weatherstrip for the side window is made of an extruded sponge rubber. The weatherstrip is the larger type that is used on most GM cars this period. Available by the foot.
13/16" Trunk Weatherstrip
p/n: 50-0161-85
This Trunk Weatherstrip was designed from an original part for a specific application but has many uses outside of its original purpose. Available by the foot.
9/16" Trunk Weatherstrip
p/n: 60-0411-85
This Trunk Weatherstrip is made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
Starter Solenoid Cable Rubber Boot
p/n: 70-0704-21
This Starter Solenoid Cable Rubber Boot is designed from the original part for superior fitment and function. This boot covers and protects the battery cable at the starter solenoid connection.
Brown Door Lock Knob
p/n: 70-0660-70
This is the Knob or push button for the inside door lock. The part fits over 1/8" steel rod to door lock. Neutral brown color that may be lacquered with other colors as required. A hard rubber part fits many different vehicles.
3/4" Trunk Weatherstrip
p/n: 70-0463-85
This Trunk Weatherstrip is made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
Wiper control grommet
p/n: 60-0197-53
Grommet, wiper control connection link. Replaces #4161287. 11/32" I.D. X 19/32" O.D.
Shift Lever Grommet
p/n: 50-0284-24
Grommet, shift lever insulator. One (1) per car. Three eighths (3/8) inch inside diameter by five eighths (5/8) inch barrel by one half (1/2) inch long.
Side Window Roller
p/n: 70-0117-62
This Side Window Roller, anti-rattle roller, is manufactured using EPDM dense rubber to replace the original perfectly. The roller fits both styles of brackets.
Glovebox Link Bumper
p/n: 50-0367-88
This Glovebox Link Bumper is made to original specifications for an authentic fit and appearance. The glovebox check link bumper fits on the glovebox door arm.
Window Stop Stem Bumper
p/n: 33-0540-62
This Window Stop Stem Bumper is fully molded and designed from the original part for superior fitment and seal. Designed as a window stop cushion for front and rear door, rear side and quarter windows as required.
Hood Bumper
p/n: 50-0490-42
Bumper, hood to fender. Uses four (4) per car for most models.Width: 1.375 inches. Height: 1.25 inches.
Wiper Transmission Gasket
p/n: 50-0484-53
Gasket, windshield wiper transmission to cowl. Steel rule die cut replacement for #4587667.
Axle Rebound Pad
p/n: 50-0302-35
Bushing, rear axle, anti-sway rod ends. Fully molded rubber. Four (4) required per car.
License lens gasket
p/n: 50-0357-17
Gasket set, rear license light assembly. One (1) rubber ring and one (1) cork rubber gasket comprise set.
Body Mounting Pad
p/n: 50-0097-48
Pad, several usages. Use as a body mounting pad or as a cushion for body mounting bolt. Fully molded rubber. Up to twenty (20) required per car.
1-5/8" Firewall Grommet
p/n: 50-0363-20
This Firewall Grommet is used to run the windshield washer hose through the firewall. Designed from original part for excellent workmanship.
Dimmer Switch Grommet
p/n: 40-0083-88
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
Clutch and Brake Pedal Bump Stops
p/n: 70-4805-24
This Clutch and Brake Pedal Bump Stop pair is designed from the original part for superior fitment, finish and function. These rubber bumpers help align your brake and clutch pedals in the correct position, while also preventing rattles and squeaks.
Parking/Backup Light Lens Gasket
p/n: 70-1272-16
Gasket, parking light lens and backup light lens. Die cut from one eighth (1/8) inch rubber.
Body Mounting Pad
p/n: 50-0096-48
Pad, body mounting. Fully molded rubber with steel core and locating collar.
Rear coil spring pad
p/n: 50-0304-35
Insulator, rear coil spring clamp bolt (upper end). Two (2) per car. Fabric reinforced rubber as original.
Hood Bumper
p/n: 50-0159-42
Bumper, hood ledge corner at shroud.Width: 1.25 inches. Height: .5 inches.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Quarter Window Vertical Leading Edge
p/n: 70-0141-58
This quarter to side window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. Slides into metal retaining channel attached to rear side window and seals between the front door window and the rear quarter window.
Hydraulic Pump Mounting Cushion
p/n: 70-0852-67
This Hydraulic Pump Mounting Cushion is designed from the original part for superior fitment and function. Used on models with hydraulic window lifts or a hydraulic convertible top. Two (2) to three (3) required per car.
Door Handle Gasket Set
p/n: 50-0322-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Body Mounting Pad
p/n: 50-0477-48
Pad, body mounting. Fully molded rubber with metal core & locating collar.
Heater control valve seal
p/n: 50-0356-20
Seal, heater control valve. High quality sponge rubber designed to cushion heater control valve and keep out noise and water. For all except right-hand drive.
Trunk Bumper
p/n: 70-0296-87
T-nut, trunk bumper in gutter at sides, brass core tapped 10-32 thread. Two (2) required per car. For models having partial weatherstrip in gutter of body.
Reflector gasket
p/n: 50-0360-15
Seal, reflector signal, between taillights. With correct slits for tabs on reflector. One (1) pair required per car.
Front coil spring pad
p/n: 50-0358-35
Insulators, front coil spring. Fabric reinforced rubber as original.
Clutch and Brake Pedal Pads - Black
p/n: 50-0054-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Parking Brake Pedal Pad
p/n: 50-0348-22
Pad, parking brake pedal. Without "PARK" written on pad. Black only. For pedal pad with "PARK" written on pad see our #50-0405-22.Height: 2.0 inches.
Parking Light Lens Gasket
p/n: 50-0353-16
Gasket, front parking lens. High quality sponge rubber better than original. One (1) pair per car.Width: 3.375 inches. Height: 2.625 inches.
Brake and Clutch Shank Seal
p/n: 50-0066-24
Grommet, brake and clutch pedal floor seal.Width: 1.8125 inches. Height: 2.375 inches.
Rigid Run Channels
p/n: 70-0516-58
This Rigid Run Channel pair is zinc plated steel with black cloth inside lining to provide a smooth sliding surface for glass movement. Also works to protect the glass. Fastens in place by small screws or rivets on top and bottom.
Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
Parking Light Lens Gasket
p/n: 50-0351-16
Gasket, headlight door parking lens. Constructed out of soft durable rubber.Height: .375 inches.
Headlight Mounting Pad
p/n: 70-0201-14
This Headlight Mounting Pad is designed from the original part for superior fitment and seal. This pad acts as the headlight adjusting collar. Sold as a pair.
Heater control valve seal
p/n: 50-0347-20
Seal, heater control valve. High quality sponge rubber designed to cushion heater control valve and keep out noise and water.
Parking and Signal Gasket
p/n: 50-0354-16
Gasket, front parking and signal light to fender. One (1) pair per car. Fits between signal lamp body and headlamp to fender adapter.Width: 4.0 inches.
Suspension Bumper - Front Lower Control Arm
p/n: 50-0092-32
This Suspension Bumper is designed from the original part for superior fitment and function. Bumper mounts to the front suspension lower control arm. Two (2) per car required.
Sliding Quarter Window Weatherstrip
p/n: 70-0353-78
This Sliding Quarter Window Weatherstrip is used for side window inner and/or outer, front and/or rear doors. Available in a 6ft. lengths.
Chrome Fender Welting - 25ft
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Clutch and Brake Pedal Pads - Brown
p/n: 50-0054-89
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality brown rubber.
Front Stabilizer Bushing
p/n: 50-0094-34
Bushings, front stabilizer shaft-to-frame or stabilizer shaft, front or rear. Fully molded rubber.
Headlight Door To Lens Ring Seals
p/n: 70-0389-14
This Headlight Door To Lens Ring seal pair is designed from the original part for superior fitment and function. The part works to seal between the headlight door housing and the headlight retaining ring. The part is a single lip type seal for sealed beam headlights.
Window Felt Beltline Weatherstrips
p/n: 70-0555-58
These Window Felt Beltline Weatherstrips are sold as a three (3) foot pair. The beltline is used for side windows inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Rigid Run Channels
p/n: 70-0347-58
This Rigid Run Channel pair is stainless beaded and mohair-lined to help eliminate window rattles and provide a smooth sliding surface for glass movement. Also works to protect the glass.
Taillight Gasket
p/n: 50-0355-15
Gasket, rear stop and turn signal. Four (4) piece set required per car.
Side Window Vent Frame Upper Bumpers
p/n: 60-0183-62
These Side Window Vent Frame Upper Bumpers (pair) are designed from the original part for superior fitment and function. This glass bumper fits in vent frame at the top on the right and left sides of the vehicle.
Rear coil spring pad
p/n: 50-0359-35
Insulators, rear coil spring. Fabric reinforced rubber as original. One (1) pair per car.
Clutch Equalizer Bushing and Seals
p/n: 70-2029-24
This Clutch Equalizer Bushing and Seal set is designed from the original part for superior fitment and operation. The set includes a metal sleeved rubber bushing and two (2) molded rubber seals for each end of equalizer shaft.
Vent Division Bar Weatherstrip
p/n: 70-1753-56
This Vent Division Bar Weatherstrip pair is fully molded with metal cores and attaching tabs.
Stabilizer Bar End Link Set
p/n: 70-0567-34
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt. 5/16"-24NF x 7-5/8" long. Includes metal sleeves, cup washers and rubber grommets.
Door Bumper
p/n: 70-0168-71
Bumper, door side. Square type held by four (4) screws, metal core as original.
Hood to Cowl Weatherstrip
p/n: 70-0497-43
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This seal mounts at the rear of the engine bay to seal between the hood and vehicle body cowl.