Body Weatherstrip Kit
p/n: 90-3278-90
This Body Weatherstrip Kit includes the major weatherstrip components and some other essential parts needed for the body of your restoration project.
Convertible Roof Rail Weatherstrip Set
p/n: 70-0757-65
This Convertible Roof Rail Weatherstrip Set fits on the folding roof of the vehicle and seals the side window when the window is fully raised.
Front Door Vent Window Set
p/n: 90-0412-90
This Front Door Vent Window Set is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Engine Mount Service – Revulcanization Only
p/n: 70-1774-11
This Revulcanization Service Only is designed to restore your Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Front Door Vent Window Weatherstrips
p/n: 38-0074-55
These Front Door Vent Window Weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Windshield Gasket
p/n: 70-0820-50
This Windshield Gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
Front Door Weatherstrips
p/n: 70-0848-72
A Front Door Weatherstrip pair with molded ends. This part is the primary door to body weatherstrip. Includes pins and clips for easy installation.
Engine Mount Service – Revulcanization Only
p/n: 50-0273-11
This Revulcanization Service Only is designed to restore your Front Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Steering Column Floorplate
p/n: 50-0412-36
Floorplate, steering column. Metal core just like the original.
Rear Axle Suspension Bumper
p/n: 70-2638-35
This Rear Axle Suspension Bumper is fully molded with new rubber vulcanized to new steel cores. Used on all models with conventional spring suspension.
Transmission Mount Service
p/n: 50-0264-25
Support pad, transmission mount (insulator). Revulcanization service only.Length: 5.0 inches. Width: 2.0 inches.
Torque ball service
p/n: 50-0190-27
Retainer, torque ball, heavy steel jacket with molded rubber inner collar. Revulcanization service only.
Rigid Run Channels
p/n: 70-0536-58
A Rigid Run Channel pair with bright beaded edge, mohair lined channel, die trimmed and round formed at the top. Sold in 29" pairs.
Axle Rebound Pad
p/n: 50-0370-35
Bumper, rear axle stop. Molded left and right. Revulcanization service only.
Support Arm Bumper
p/n: 50-0526-32
Bumper, lower support arm. With metal core and attaching bolt. One (1) pair per car.Width: 2.4375 inches. Height: 4.0 inches.
Quarter Window U Jamb Lock Pillar Fillers
p/n: 70-0729-79
This Quarter Window U Jamb Lock Pillar Filler pair is designed from the original part for superior fitment and sealing. This right and left weatherstrip filler mounts at the bottom of the rear side window, lower leading edge to seal the rear quarter window. Also known as a Door U Jamb Seal.
Front Door Auxiliary Weatherstrips
p/n: 70-0551-73
This Front Door Auxiliary Weatherstrip pair fits to the left and right doors at the beltline. Uses snap-in fasteners, four (4) each included.
Rear coil spring pad
p/n: 50-0359-35
Insulators, rear coil spring. Fabric reinforced rubber as original. One (1) pair per car.
Transmission Mount Service
p/n: 50-0186-25
Insulator, engine support at transmission. Revulcanization service only.Length: 7.375 inches. Width: 1.75 inches. Height: 1.5 inches.
Side Window Vent Frame Upper Bumpers
p/n: 60-0183-62
These Side Window Vent Frame Upper Bumpers (pair) are designed from the original part for superior fitment and function. This glass bumper fits in vent frame at the top on the right and left sides of the vehicle.
Rigid Run Channels
p/n: 70-0347-58
This Rigid Run Channel pair is stainless beaded and mohair-lined to help eliminate window rattles and provide a smooth sliding surface for glass movement. Also works to protect the glass.
Power Brake Pedal Pad
p/n: 50-0406-22
Pad, power brake pedal. Available in BLACK only, "Power Brake" written with white lettering.Width: 5.5 inches. Height: 2.625 inches.
Beltline Weatherstrip Channel
p/n: 70-0651-58
This Beltline Weatherstrip Channel is a five (5) foot length of rigid channel with a flocked rubber lip and a flat stainless bead. Can be used as the inner beltline weatherstrip on front doors, rear doors and quarter windows.
Side Window Vertical Leading Edge Weatherstrips
p/n: 50-0427-80
This quarter to side window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. This part attaches to the vertical edge of the rear side windows when the rear side windows are fully raised.
Vent Division Bar Weatherstrip
p/n: 70-0922-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Headlight Ring Gasket Set
p/n: 70-1465-14
This four (4) piece Headlight Ring Gasket Set is designed from the original part for superior fitment and seal. This gasket is for the headlight outer rim to sealed beam headlight retainer ring. Possible fit for models with dual headlights.
Front Coil Spring Pad
p/n: 50-0476-35
Pad, front coil spring insulator, upper. Two (2) per car, five and one eighths (5-1/8) inch outside diameter. Height: .28125 inches.
Front Stabilizer Bushing
p/n: 50-0094-34
Bushings, front stabilizer shaft-to-frame or stabilizer shaft, front or rear. Fully molded rubber.
Taillight Lens Gasket
p/n: 50-0197-15
Gasket, taillight lens, one fourth (1/4) inch thick sponge rubber.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0773-WT
This Steele exclusive Peel-N-Stick Trunk Weatherstrip is designed from the original part for superior fitment and seal. This easy to install weatherstrip mounts around the full perimeter of the trunk directly to the body.
Parking, Signal Light Lens Gaskets - Front
p/n: 50-0192-16
This front Parking and Turn Signal Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Light Lens and the Light Housing or Bezel.
Front Door Hinge Pillar Weatherstrips
p/n: 70-0552-73
This Front Door Hinge Pillar Weatherstrip pair is designed from the original parts for superior fitment and seal. The pair attaches above the beltline, hinge pillar windshield post. These two (2) strips with pre-installed clips, one for each door, are manufactured for a factory like fit.
Rigid Run Channels
p/n: 70-0516-58
This Rigid Run Channel pair is zinc plated steel with black cloth inside lining to provide a smooth sliding surface for glass movement. Also works to protect the glass. Fastens in place by small screws or rivets on top and bottom.
Parking Brake Pedal Pad
p/n: 50-0405-22
Pad, parking brake pedal. With "PARK" written on pad. Black only. For pedal pad without "PARK" written on pad see our #50-0348-22.Width: 2.0625 inches.
5" Wide Bow Drill Cloth Tape
p/n: 70-1175-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Black in color and available in a five (5) foot roll.
Trunk Weatherstrip
p/n: 70-0773-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Door Handle Gasket Set
p/n: 50-0515-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
2-1/2" Black Bow Drill Cloth Tape
p/n: 70-1172-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Black in color and available in a five (5) foot roll.
Hood Bumper
p/n: 50-0194-42
Bumper, hood side on fender ledge center. Self retaining type. See our #50-0095-42 for rear type.Height: 1.625 inches.
Body Mounting Pad
p/n: 50-0096-48
Pad, body mounting. Fully molded rubber with steel core and locating collar.
Rear coil spring pad
p/n: 50-0304-35
Insulator, rear coil spring clamp bolt (upper end). Two (2) per car. Fabric reinforced rubber as original.
Glovebox Door Link Grommet
p/n: 70-0968-88
This Glovebox Door Link Grommet is designed from the original part for superior fitment and function. Grommet works to cushion the glovebox door closure.
2-1/2" Tan Bow Drill Cloth Tape
p/n: 70-1173-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Tan in color and available in a five (5) foot roll.
Steering Column Gasket - Automatic Transmission
p/n: 70-4467-36
This Steering Column gasket is designed from the original part for superior fitment and sealing. Gasket is machine cut from quality sponge rubber to authentic original dimensions. This part fits around the steering column to seal the column through the body floor pan.
Body Mounting Pad
p/n: 50-0361-48
Pad, body mounting. Required replacement for body-off restorations. Constructed of high quality rubber for long lasting durability. Two inch (2") square by fifteen sixteenths inch (15/16) inside hole diameter by one fourth inch (1/4") height.
Strut Rod Bushing
p/n: 50-0522-27
Bushing, strut rod at drive shaft tube. Two (2) per car required.Length: 1.65625 inches.
Axle Rebound Pad
p/n: 50-0302-35
Bushing, rear axle, anti-sway rod ends. Fully molded rubber. Four (4) required per car.
Hood Bumper
p/n: 50-0205-42
This Hood Bumper is the adjustable type for the front of the hood. Used to support/cushion the hood closure. Cadmium plated bolt (5/16)-18 x 1-1/4". Excellent appearance with authentic details like original.
Hood bumper
p/n: 50-0095-42
Bumper, hood to fender ledge. Self retaining type. See our # 50-0194-42 for center type.
1-9/16" Firewall Grommet
p/n: 50-0566-20
This Firewall Grommet is used to used to run the water temperature gauge, heater blower wire, or other various wires through the firewall. Designed from the original part for superior fit and seal.
Glovebox Link Bumper
p/n: 50-0367-88
This Glovebox Link Bumper is made to original specifications for an authentic fit and appearance. The glovebox check link bumper fits on the glovebox door arm.
Window Stop Stem Bumper
p/n: 33-0540-62
This Window Stop Stem Bumper is fully molded and designed from the original part for superior fitment and function. Designed as a window stop cushion for front and rear door, rear side and quarter windows as needed.
5/8" Door Weatherstrip with Clips
p/n: 70-1112-73
This Door Weatherstrip with Clips is made made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
Shift Lever Grommet
p/n: 50-0284-24
Grommet, shift lever insulator. One (1) per car. Three eighths (3/8) inch inside diameter by five eighths (5/8) inch barrel by one half (1/2) inch long.
Brown Door Lock Knob
p/n: 70-0660-70
This is the Knob or push button for the inside door lock. The part fits over 1/8" steel rod to door lock. Neutral brown color that may be lacquered with other colors as required. A hard rubber part fits many different vehicles.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
Wiper Motor Mounting Gasket
p/n: 70-4466-53
This Wiper Motor Mounting gasket is designed from the original part for superior fitment and sealing. Gasket is machine cut from quality dense rubber to authentic original dimensions. This gasket fits to mount and isolate the wiper motor to the firewall / cowl.
2-5/8" Run Channel Mohair Liner
p/n: 70-2863-58
This Run Channel Mohair Liner helps to reline the guide bars on the lock side of hardtops and convertibles. This mohair liner comes with a rubber backing and installs with adhesive to the division bars and channel. Available by the foot.
1-1/16" Trunk Weatherstrip
p/n: 70-0346-85
This Trunk Weatherstrip is designed from an original part for a specific application but has many uses outside of its original purpose. Available by the foot.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0510-WT
This Peel-N-Stick Trunk Weatherstrip is made from a high-quality EPDM sponge rubber. Available by the foot.
1" Trunk Weatherstrip
p/n: 70-0510-85
This Trunk Weatherstrip was designed from an original part for a specific application but has many uses outside of its original purpose. Available by the foot.
2-1/4" Body Hole Plug
p/n: 35-0863-45
This Body Hole Plug is fully molded and designed from the original part for superior fitment and seal. Designed for the trunk, however the generic shape makes this plug usable for a variety of applications.
5/8" Door Weatherstrip without Clips
p/n: 70-1111-73
This Door Weatherstrip made from high-quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
Door Drain Hole Seal
p/n: 60-0442-70
This Door Drain Hole Seal installs on the door bottom and is also used on the tailgate of station wagons. Two (2) required per vehicle. Molded from high-quality EPDM dense rubber.
1-3/16" Utility Plug
p/n: 35-0099-20
This Utility Plug is fully molded and designed from the original part for superior fitment and seal. This plug is made from high-quality EPDM dense rubber to provide excellent durability.
1/16" Sash Channel Filler - Cork
p/n: 70-1115-57
This 1/16" Sash Channel Filler offers the best quality cork product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
Firewall Retainer
p/n: 60-0586-20
This Firewall Retainer is used on the firewall insulation panel. Designed from original for the "Christmas Tree" style popular during this time.
Power Top Cylinder Spacer
p/n: 70-0822-67
This Power Top Cylinder Spacer is used as the folding top power cylinder support. Molded from 100% EPDM dense rubber for durability. Four (4) spacers used per car.
1/16" Sash Channel Filler - Rubber
p/n: 70-2170-57
This 1/16" Sash Channel Filler offers the best quality rubber product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
Door Lock Bumper
p/n: 34-0484-71
This Door Lock Bumper is made from high-quality EPDM dense rubber to provide excellent durability. Designed for applications such as the upper door lock post.
Door or Tailgate Bumper
p/n: 33-1228-71
This Door Bumper is fully molded and designed from the original part for superior fitment. This rubber bumper attaches to the vehicle body to support / cushion the door closure. Usually requires two (2) bumpers each per vehicle.
1/32" Sash Channel Filler - Cork
p/n: 70-1114-57
This 1/32" Sash Channel Filler offers the best quality cork product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
1/32" Sash Channel Filler - Rubber
p/n: 70-2169-57
This 1/32" Sash Channel Filler offers the best quality rubber product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
1/4" Universal Mounting Pad
p/n: 70-0308-17
This Universal Mounting Pad is used for lights, hinges, brackets, and other bright work when no molded pad is available. Manufactured with a special edge lip to hug bright work when clamped down. Shape outline to suit application.
Door Bumper
p/n: 33-1227-71
This Door Bumper is fully molded and designed from the original part for superior fitment. The twin retainer style rubber bumper attaches to the vehicle body to support/cushion the door closure. Usually requires two (2) bumpers each per vehicle.
3/4" Body Hole Plug
p/n: 35-0369-20
This Floor Plug is fully molded and designed from the original part for superior fitment and seal. Designed for shroud or cowl upper panel gauge holes and for various body holes requiring a plug.
3/4" Trunk Floor Pan Plug
p/n: 35-0070-87
This Trunk Floor Pan Plug is fully molded and designed from the original part for superior fitment and seal. This plug is made from high-quality EPDM dense rubber to provide excellent durability.
Hood and Trunk Bumper Cap for Adjustment Screw
p/n: 70-0294-42
This Hood and Trunk Bumper Cap is designed from the original part for superior fitment, finish and function. Cap type for front hood or rear trunk lid adjustment screw.
Hydraulic Pump Mounting Pad
p/n: 70-0946-67
This Hydraulic Pump Mounting Pad is designed from the original part for superior fitment and function. For folding top hydraulic pump mount. Special design to hold pump mounting bracket to floor pan. Four (4) pads needed per car. Height: 1" inch.
7/8" Trunk Bumper
p/n: 33-0293-87
This 7/8" Trunk Bumper is a quality reproduction of the original factory part. Self-retaining bumper is manufactured to OEM specifications to install for an authentic fit, finish, and function.
Door Weatherstrip Fastener
p/n: 50-0198-73
This Door Weatherstrip Fastener is steel with a black finish. Each push-in fastener measures one half (1/2") inch long with a thirteen thirty second (13/32") inch diameter head. Reproduction fastener is designed from the original part to fit correctly.
Hood Weatherstrip Retainer
p/n: 70-0564-42
Fastener, hood to cowl weatherstrip (and other uses), self-retaining button head retainer.
Lock Cylinder Gasket
p/n: 60-0641-69
This Lock Cylinder Gasket is die cut from one-thirty-second (1/32) inch neoprene.
13/16" Firewall Grommet
p/n: 32-0158-17
This Firewall Grommet is designed from the original part for superior fitment and seal. Designed for firewall applications such as running the hand brake cable through the firewall or the license light through the trunk.