Side Window Vertical Leading Edge
p/n: 70-1586-80
This quarter to side window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. This part attaches to the vertical edge of the rear side windows when the rear side windows are fully raised.
Rear Door Lock Pillar Fillers
p/n: 70-1816-79
This Rear Door Lock Pillar Filler pair is designed from the original part for superior fitment and sealing. This right and left weatherstrip filler mounts at the bottom of the rear side window, lower leading edge to seal the rear door window. Fully molded authentic rubber construction.
Vent division bar weatherstrip
p/n: 60-0636-56
Front vent window division post seal. Fully molded with metal core and attaching tabs. This part fits opposite the glass run channel and seals the vent window when the vent is closed. See Front door vent weatherstrip for main rubber seal.
Vent Division Bar Weatherstrip
p/n: 70-0880-56
This Vent Division Bar Weatherstrip is fully molded with metal core and attaching tabs. This part fits opposite the glass run channel and seals the vent window when the vent is closed.
Side Window Vertical Leading Edge
p/n: 60-0633-80
This Side Window Vertical Leading Edge Weatherstrip attaches to the vertical edge of the rear side windows when the rear side windows are fully raised. Molded authentic rubber construction with metal core, this part does not include the chrome piece.
Vent division bar weatherstrip
p/n: 50-0450-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Vent Division Bar Weatherstrip
p/n: 70-0849-56
Front vent window division post seal. Eleven and one half inches (11.5") and one half inch high. Fully molded with metal core and attaching tabs.
Vent Window Division Bar Weatherstrips
p/n: 50-0332-56
This Front Vent Window Division Bar / Post Weatherstrip pair is designed from the original part for superior fitment and seal. This piece mounts on the vertical division bar and seals as the vent glass closes against it.
Vent division bar weatherstrip
p/n: 70-0859-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Running Board or Inner Fender Splash Filler
p/n: 60-0288-45
This eight (8) foot Splash Filler strip is used for the running board apron to body or fender splash panels anti-rattle filler. This filler strip is top-quality EPDM sponge rubber to accept rivets or retaining screws.
Headlight Ring Gasket Set
p/n: 70-1465-14
This four (4) piece Headlight Ring Gasket Set is designed from the original part for superior fitment and seal. This gasket is for the headlight outer rim to sealed beam headlight retainer ring. Possible fit for models with dual headlights.
Flexible Run Channel
p/n: 70-1238-58
Cloth covered, mohair lined flexible metal channel for sides and top of door windows.
Side Window Vertical Leading Edge
p/n: 70-0832-80
This quarter to side window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. This part attaches to the vertical edge of the rear side windows when the rear side windows are fully raised.
U Jamb Door Lock Pillar Fillers
p/n: 70-0877-79
This quarter window U Jamb Door Lock Pillar Filler pair is designed from the original part for superior fitment and sealing. This right and left weatherstrip filler mounts at the bottom of the rear side window, lower leading edge to seal the rear quarter window. Also known as a Door U Jamb Seal.
Vent division bar weatherstrip
p/n: 70-1533-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Splash Apron / A-Arm / Radiator Dust Shield Set
p/n: 70-4679-45
This four (4) piece Splash Apron / A-Arm / Radiator Dust Shield Filler set is designed from the original part for superior fitment, finish, and function. Filler pieces are die cut from quality masticated rubber to authentic original dimensions.
Door Hinge Seals
p/n: 70-1460-70
This Door Hinge Seal installs on the front door hinge pillar at the beltline. These seals are sold as a pair for the left and right side.
Body Bumper Kit
p/n: 90-0208-90
This fourteen (14) piece Body Bumper Kit is designed from the original part for superior fitment, finish and function. Designed from originals and made from top quality rubber to ensure durability.
Body Bumper Kit
p/n: 90-0211-90
This fourteen (14) piece Body Bumper Kit is designed from the original part for superior fitment, finish and function. Designed from originals and made from top quality rubber to ensure durability.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0773-WT
This Peel-N-Stick Trunk Weatherstrip is designed from the original part for superior fitment and seal. The weatherstrip mounts around the full perimeter of the trunk directly to the body.
Fender Skirt Edge Weatherstrip
p/n: 60-0201-45
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment and seal. This weatherstrips fits between the removable fender skirt and the rear fender quarter panel.
Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
Body Mounting Pad
p/n: 60-0383-48
Cushion assembly body mounting pad. Fully molded rubber with metal core, locating collar and metal bolt sleeve. Rectangular.
Rigid Run Channels
p/n: 70-0516-58
This Rigid Run Channel pair is zinc plated steel with black cloth inside lining to provide a smooth sliding surface for glass movement. Also works to protect the glass. Fastens in place by small screws or rivets on top and bottom.
Transmission Mount Service
p/n: 60-0465-25
Transmission mount. One (1) per car. Revulcanization service only.Length: 5.75 inches.
Luggage Rack Pads
p/n: 70-3459-87
This Luggage Rack Pad set is designed from the original part for superior fitment and seal. A five (5) piece set for Station Wagon models with an OEM factory luggage rack.
Hood to radiator weatherstrip
p/n: 60-0670-42
Weatherstrip or seal, hood panel to radiator support. Correct extruded rubber strip. Used on vehicles with factory A/C.
5" Wide Bow Drill Cloth Tape
p/n: 70-1175-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Black in color and available in a five (5) foot roll.
Wiper Transmission Gasket
p/n: 60-0593-53
Wiper Transmission Gasket - This is the seal for the wiper motor crank. For two (2) speed wiper motors only. These parts are made of the highest quality and authenticity. Replaces # 4906021.
Splash Apron / A-Arm Dust Shield Set
p/n: 70-2511-45
This four (4) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Trunk Weatherstrip
p/n: 70-0773-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Taillight Gasket
p/n: 60-0693-15
Seal, taillight bezel. Correct profile and long lasting material. Six (6) strips cut twelve and three fourths (12-3/4) inches long.Length: 12.75 inches.
Splash Apron Filler Shield Set
p/n: 70-2510-45
This four (4) piece Splash Apron / A-Arm Dust Shield Filler Set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Hood to Cowl Weatherstrip
p/n: 70-4693-43
This Hood To Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This weatherstrip installs at the rear of the engine bay to seal between the hood and vehicle body cowl.
Front Stabilizer Bar End Link Set
p/n: 70-2109-33
A twenty-two (22) piece Front Stabilizer Bar End Link set. Comes complete with fasteners, metal sleeves, metal cup washers and black rubber bushings. One (1) end link set for both sides of stabilizer bar on one (1) car.
Body Mounting Pad
p/n: 60-0382-48
Cushion assembly (body mounting pad). Rubber with metal core, locating collar and metal bolt as original. Metal bolt is removable, measures fifteen sixteenths inch (15/16") long when removed.
Door Handle Gasket Set
p/n: 70-0925-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Body Mounting Pad
p/n: 70-1749-48
This Body Mounting Pad is fully molded rubber with a metal core and locating collar. These frame pads are installed between the frame and the floor pans.
Fuel Filler Neck Grommet
p/n: 70-1439-39
This Fuel Filler Neck Grommet is designed from the original part for superior fitment and seal. This grommet fits around the vehicles fuel filler neck between the filler neck and vehicle body. Fits as original.
Stabilizer Bar End Link Set
p/n: 60-0221-33
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt 3/8"-16 NF x 6-15/16" long. Comes with metal sleeve, metal cup washers and rubber grommets.
Brake Master Cylinder Push Rod Boot
p/n: 60-0180-24
This Brake Master Cylinder Push Rod Boot is made from high-quality Nitrile rubber for a precise, factory like fit for your classic vehicle. Manufactured to OEM specifications to install for an authentic fit and finish.
Quarter Window Vertical Leading Edge
p/n: 70-0141-58
This quarter to side window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. Slides into metal retaining channel attached to rear side window and seals between the front door window and the rear quarter window.
Rear Bumper to Body Dust Shield Filler
p/n: 70-3363-45
This two (2) piece Rear Bumper To Body Dust Shield filler pair is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Hood to Cowl Weatherstrip
p/n: 60-0417-42
This Hood to Cowl Weatherstrip mounts at the rear of the engine bay to seal between the hood and vehicle body cowl. One strip required for one (1) car.
Rocker Panel Inner Drain Cover
p/n: 70-2392-45
This Rocker Panel Inner Drain Cover pair is designed from the original part for superior fitment and seal. Fully molded with proper attaching teeth and flap.
Splash Apron / A-Arm Dust Shield
p/n: 70-2509-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Splash Apron / A-Arm Dust Shield
p/n: 70-2801-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.