Grommets, sidemount. These are the very large type, right and left. Used simultaneously with our #70-0388-37. Compare with your original. (See also our #70-0388-37).
Grommets/seals, for sidemounted spares, cover hole in fender. Large, fully flanged for fender metal, compare to our #70-0341-37 and your original. Symmetrical, right and left. Approximately five and three fourths (5-3/4) inches by eight (8) inches outside
Mounting pad set, headlight and headlight bracket. Light pad has metal core and high collar as original to accommodate headlight adjustment.
Grommets, spare wheel sidemount arm.
Bumper, front spring, upper arm on frame. Rubber with heavy steel core, including five sixteenths (5/16) inch stud.
Grommets, rear bumper. For vehicles without luggage racks.
This front door vent window weatherstrip set contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Weatherstrip, front bow-to-windshield, soft rubber, hollow body, proper screw holes, hinged flaps front and back.
Pivot, hood hinge top strap. Cold rolled steel as original. Furnished in a four and one half (4-1/2) foot strip long enough for all models.
Mounting pad, windshield lower frame to body. Forty eight (48) inches long. Molded in two (2) parts with joint in center. Canvas base as original.
Installing tool, door and trunk handle ferrule. For cars and trucks using door and trunk handle ferrules such as our #70-0111-69.
Pad, motor support, rear. Revulcanization service only. Send in your old plates with studs intact. Rebound cushion, furnished with mount.
This Side Mount Spare Grommet Set is made from top-quality EPDM rubber and designed from the original parts for durability and proper function. This set is for the rear spare wheel mount on cars without a luggage rack.
Protector, hood center. Brass core as original threaded to fit original screws.
Seals, shock absorber and rear stabilizer link. Eight (8) piece set.
Hose, air inlet, radiator shroud to air silencer. Two and one eighths (2-1/8) inch outside diameter by nine and three eighths (9-3/8) inch long. Beautiful copy of rare original part.
Grommets, luggage rack brace rod through body. Styles with luggage rack arms.
Pads, hood corners. right and left. Threaded brass core.
Boot, vacuum brake cylinder main rod. Accordion type, two (2) inches diameter by six (6) inches. Top quality workmanship and material.Length: 6.0 inches.
Cadillac Motors pedal pads. Authentic straight diamond pattern. Especially good copy, fine detail.
Pads, hood rear corners. Threaded metal core.
Seals, shock absorber and rear stabilizer link. Eight (8) piece set.Width: 1.1875 inches.
Pad, taillight mounting. Double bead as original.
Grommets, front bumper. Theses are for the round, tubular bumper support.
Motor mount pad. Cloth base as original, low type, two (2) inches outside diameter by seven eighths (7/8) inch thick.
Cadillac V-8 pedal pads, clutch and brake. Another rare one we finally found to copy. Superior copy.
Bumper, hood ventilator door, self retaining. Five sixteenths (5/16) inch diameter, forty eight (48) piece set.
Grommets, ride regulator control rod through fender splash shield. Two (2) per car. Made without rod hole. You cut rod slot as required at installation.
Boot, brake vacuum cylinder rod, for piston type vacuum cylinder.
Shield, gearshift through floorboard, molded in all detail, including bolt holes.Length: 7.5 inches. Width: 5.875 inches.
Grommets, luggage rack arms through sheet metal, special tall type.
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide, three sixteenths (3/16) inch, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty fi
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Mounting pad, filler neck extension. Four and nine sixteenths (4-9/16) inches diameter, double bead.
Pad, door jamb edge. With metal insert as original.Length: 1.1875 inches. Width: 1.5625 inches.
Grommet, fuel filler neck. Fully molded rubber. Four and five eighths inch (4 5/8") outside diameter by two and three sixteenths inch (2-3/16") inside diameter by three fourths inch (3/4") height.
Grommet, fuel filler neck. Fully molded rubber. Flat bottom has slight ridge (seam) along edge. Four and three eighths inch (4-3/8") outside diameter by two and three sixteenths inch (2-3/16") inside hole diameter by five eighths inch (5/8") height.
Knob, gearshift. Rubber only for flanged top nut on gearshift lever.
Stainless beaded edge, mohair-lined, exact replacement for rear side of division bar. Available in 15" pairs.
Sleeve, coil wire to distributor. Fluted to match upper water hoses rubber only. V-12 & V-16 with coils mounted in radiator, V-8 with coils mounted horizontally on brace rods.
Inner Fender Seal for anti-rattle, running board apron to body, or fender splash panels. Nine sixteenths (9/16) inch by seven eighths (7/8) inch slotted sponge rubber to accept rivets. Sold in eight (8) foot strips.
Boot, gearshift. Brown rubber. For black see our #50-0035-24.Color:brown Width: 2.8125 inches.
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Seal, steering column to toe board. Three fourths (3/4) inch thick, high grade sponge, die cut holes.Length: 3.875 inches. Width: 3.875 inches.
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide, three sixteenths (3/16) inch, twenty five (25) foot roll. Typially used for attaching two (2) fenders to body. For f
Sash channel, side window glass. U-shaped steel channel only, no filler. Will require that you attach your own window regulator cam to underside as required.
Boot, gearshift. Black rubber. For brown see our #50-0035-89.Width: 2.8125 inches.