Search Results
Side Mount Spare Wheel Grommet
p/n: 70-0341-37
Grommets, sidemount. These are the very large type, right and left. Used simultaneously with our #70-0388-37. Compare with your original. (See also our #70-0388-37).
Side Mount Spare Wheel Grommet
p/n: 70-0388-37
Grommets/seals, for sidemounted spares, cover hole in fender. Large, fully flanged for fender metal, compare to our #70-0341-37 and your original. Symmetrical, right and left. Approximately five and three fourths (5-3/4) inches by eight (8) inches outside
Carburetor air intake hose
p/n: 70-0290-41
Hoses, carburetor air intake. Two (2) per car. Sixteen and three fourths (16-3/4) inches long, two (2) inches inside diameter one end, two and one fourth (2-1/4) inches inside diameter other end. Trim to proper length when installing.
Front spring bumper
p/n: 70-0339-32
Bumper, front spring, upper arm on frame. Rubber with heavy steel core, including five sixteenths (5/16) inch stud.
Hood hinge top strap pivot
p/n: 70-0045-42
Pivot, hood hinge top strap. Cold rolled steel as original. Furnished in a four and one half (4-1/2) foot strip long enough for all models.
Ferrule installing tool
p/n: 70-0662-69
Installing tool, door and trunk handle ferrule. For cars and trucks using door and trunk handle ferrules such as our #70-0111-69.
Side mount spare grommet kit
p/n: 70-0180-37
Grommet kit, rear spare wheel mount for cars without luggage rack. Three (3) piece set consisting of two (2) large grommets, one (1) small grommet.
Hood center protector
p/n: 70-0342-42
Protector, hood center. Brass core as original threaded to fit original screws.
Shock and stabilizer seal
p/n: 70-1185-33
Seals, shock absorber and rear stabilizer link. Eight (8) piece set.
Ride Regulator Control Grommet
p/n: 70-0332-33
Grommets, ride regulator control rod through fender splash shield. Two (2) required per car.Length: 2.4375 inches. Width: 2.0 inches.
Luggage rack grommet
p/n: 70-0287-46
Grommets, luggage rack brace rod through body. Styles with luggage rack arms.
Cadillac Motors pedal pad
p/n: 70-0076-22
Cadillac Motors pedal pads. Authentic straight diamond pattern. Especially good copy, fine detail.
Shock and stabilizer seal
p/n: 70-1184-33
Seals, shock absorber and rear stabilizer link. Eight (8) piece set.Width: 1.1875 inches.
Front bumper grommet
p/n: 70-0103-28
Grommets, front bumper. Theses are for the round, tubular bumper support.
Motor Mount
p/n: 70-0244-48
Motor mount pad. Cloth base as original, low type, two (2) inches outside diameter by seven eighths (7/8) inch thick.
Hood Vent Bumper
p/n: 33-0053-42
Bumper, hood ventilator door, self retaining. Five sixteenths (5/16) inch diameter, forty eight (48) piece set.
Brake vacuum cylinder rod boot
p/n: 70-0485-24
Boot, brake vacuum cylinder rod, for piston type vacuum cylinder.
Fender welting 1/4" bead 50ft
p/n: 70-1098-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five
Fender welting 3/16 bead 50ft
p/n: 70-1100-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide, three sixteenths (3/16) inch, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty fi
Fender welting 50ft chrome
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Filler neck extension pad
p/n: 70-0123-41
Mounting pad, filler neck extension. Four and nine sixteenths (4-9/16) inches diameter, double bead.
Rigid Run Channel
p/n: 70-0347-58
Stainless beaded edge, mohair-lined, exact replacement for rear side of division bar. Available in 15" pairs.
Coil wire sleeve
p/n: 70-0109-21
Sleeve, coil wire to distributor. Fluted to match upper water hoses rubber only. V-12 & V-16 with coils mounted in radiator, V-8 with coils mounted horizontally on brace rods.
Inner Fender Seal
p/n: 60-0288-45
Inner Fender Seal for anti-rattle, running board apron to body, or fender splash panels. Nine sixteenths (9/16) inch by seven eighths (7/8) inch slotted sponge rubber to accept rivets. Sold in eight (8) foot strips.
Brown gearshift boot
p/n: 50-0035-89
Boot, gearshift. Brown rubber. For black see our #50-0035-24.Color:brown Width: 2.8125 inches.
Fender welting 1/4" bead 25ft
p/n: 70-1097-44
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For
Fender welting 25ft chrome
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Steering column floorplate
p/n: 70-0340-88
Seal, steering column to toe board. Three fourths (3/4) inch thick, high grade sponge, die cut holes.Length: 3.875 inches. Width: 3.875 inches.
Fender welting 3/16 bead 25ft
p/n: 70-1099-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide, three sixteenths (3/16) inch, twenty five (25) foot roll. Typially used for attaching two (2) fenders to body. For f
Side Window Sash Channel
p/n: 70-0641-58
Sash channel, side window glass. U-shaped steel channel only, no filler. Will require that you attach your own window regulator cam to underside as required.
Gearshift boot
p/n: 50-0035-24
Boot, gearshift. Black rubber. For brown see our #50-0035-89.Width: 2.8125 inches.
Horn trumpet grommet
p/n: 70-0302-21
Grommets, horn projector. For under hood horn brackets. Two (2) per car.
Battery clamp cover
p/n: 70-0095-21
Cover, battery clamp. Control unsightly sulfate buildup. Help protect the nearby metal and finish. Good copy from original part.Length: 3.5 inches.
Door check link rod end stop
p/n: 70-0326-70
End stop and pad, door check link rod. Rubber with embedded steel plate, five sixteenths (5/16) inch diameter thread. Most models with rod type door checks.
Shock absorber bushing
p/n: 50-0087-33
Bushing, Delco type, shock absorber link. One and five sixteenths (1-5/16) inch outside diameter, seven sixteenths (7/16) inch inside diameter.
Coil wire sleeve
p/n: 70-1179-21
Sleeve, coil wire to distributor. Fluted to match upper water hoses rubber only.
1/8" Fabric Hood Lacing
p/n: 60-0578-42
Fabric hood lacing provides anti-squeak functionality. Available by the foot.
3/16" Fabric Hood Lacing
p/n: 70-2221-42
Hood lacing provides anti-squeak functionality. Available by the foot.
Door Bumper
p/n: 34-0025-42
Bumper, front and rear body hinge pillar, one (1) inch diameter by one fourth (1/4) inch thick, held by screw, steel core. Auxiliary, used only where needed to prevent door rattle.
Body mounting pad
p/n: 70-0264-48
Cushion, body bolts under washer below bracket. Fully molded rubber. One and one half inch (1 1/2") inch outside diameter by seventeen thirty seconds inch (17/32") inside hole diameter by one fourth inch (1/4") height.