This eight (8) piece kit includes the inner and outer windowfelts, upper rigid run channels, and flexible run channels needed to complete two (2) doors. Used for front or rear doors in models with vent windows in the door. Models with wood in the doors use our #70-1168-58 as lower rigid run channel.
This front door vent window weatherstrip kit is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Engine mount, side (support cushions), right and left. Side frame bracket to clutch housing bracket. Two (2) per car.Width: 2.5 inches. Height: 1.5 inches.
Installing tool, door and trunk handle ferrule. For cars and trucks using door and trunk handle ferrules such as our #70-0111-69.
Cushion, engine mount, front. Revulcanization service only.Length: 3.0 inches. Width: 2.1875 inches.
This windshield gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
This rear window gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Door edge weatherstrip. This part is the primary door to body weatherstrip.
This rumbleseat weatherstrip set is designed from original parts for superior fitment and seal. The set contains the pieces for the lower edge and corners.
Insulator replacement set. 2-piece unit of special soft rubber to be used with original steel channel and plate.
Step pad, rumbleseat, on rear fender, with bowtie emblem. Steel core with bolt.Width: 4.375 inches. Height: 5.25 inches.
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide, three sixteenths (3/16) inch, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty fi
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Grommets, rear bumper, right and left, for round bumper support bracket; left hand grommet has clearance for electrical conduit. Left hand grommet measures three and seven eighths inch (3-7/8") length by two and seven eighths inches (2-7/8") outside width
Bumpers, hood front corners. Right and Left with metal cores.Width: 1.625 inches.
Rebound bumper, front spring and rear spring for beam axle cars, steel ring reinforced as original.Height: 2.4375 inches.
Grommet, steering column at floor, brass core. Brown rubber only.
Pad, door jamb edge. With metal insert as original.Length: 1.1875 inches. Width: 1.5625 inches.
Grommet, front bumper. Fully molded rubber. For vehicles with knee action. Three and one half inches (3-1/2") outside length by two and seven eighths inch (2-7/8") outside width. One and one half inch (1-1/2") inside hole length by one half inch (1/2") in
Seal, wheel streamliner (fenderskirt) to fender. Two (2) strips each cut five (5) foot long.Length: 60.0 inches. Width: .625 inches.
Cover, brake master cylinder filler and inspection hole. Metal core as original.
Bulb type seal, gravel shield-to-rear bumper, anti-squeak. Also used as a door weatherstrip for some makes and models. Twelve (12) foot strip.
Stainless beaded edge, mohair-lined, exact replacement for rear side of division bar. Available in 15" pairs.
Mounting pad, headlight bracket to fender.Length: 4.8125 inches.
Pad, rumbleseat step, on rear bumper bracket or fender. Rubber cover only, full slip-over type with bowtie emblem.
Boot, rear, brake cable end at brake backing plate. Three and one half (3-1/2) inches long.Length: 3.50 inches.
Weatherstrip, cowl vent. Original solid rubber configuration, not a sponge substitute. A top quality part for your classic vehicle restoration.
Bushing, rear spring front eye, inlox cartridge type as original.
Cloth covered, mohair lined flexible metal channel for sides and top of door windows. Available in 5ft and 6ft lengths.
Pad, accelerator pedal. Slip-over type for original core.Length: 9.125 inches.
Grommet, fuel filler neck. Fully molded rubber, slightly angled with retaining flange. Three and seven sixteenths inch (3 7/16") outside width by three and five eights inch (3 5/8") outside length by two and three sixteenths inch (2 3/16") inside hole dia
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Pads, brake and clutch pedals. One and seven eighths (1-7/8) inch by four (4) inch overall. Excellent detail with bowtie emblem like original.
Grommet, accelerator rod through toe board. Brass core and center bushing as original.
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide, three sixteenths (3/16) inch, twenty five (25) foot roll. Typially used for attaching two (2) fenders to body. For f
Bumper pad, rumbleseat lid, upper corners. Compare with our #70-0120-87.Width: 1.0 inches. Height: 1.125 inches.
Sash channel, side window glass. U-shaped steel channel only, no filler. Will require that you attach your own window regulator cam to underside as required.
Seal, fuel filler flange. Fully molded rubber, slightly angled. Three and eleven sixteenths inch (3 11/16") outside diameter by two and three sixteenths inch (2-3/16") top hole diameter by two and five eighths inch (2 5/8") bottom hole diameter. One and o
Grommet, muffler pipe support.Length: 3.125 inches.
Cushion, horn blowing button.Height: 1.0 inches.
Pad, bracket mounting to body for tail and license plate light.Length: 3.3125 inches. Width: 2.5625 inches.
Starter button, push on replacement to rod. Two (2) inch outside diameter.
Pad, taillight mounting to rear fender.Length: 1.0625 inches.
Gasket, set, inner and outer, for divided windshield center post. Two (2) piece set.
Pad, taillight bracket to fender. Four (4) inches long. Compare with our #60-0172-15 and #60-0545-15.Length: 4.0 inches.
Grommet, firewall, oblong four (4) hole style. Fits steel retainer for throttle and choke cables, oil and temperature lines.
Cover, starter pedal button. Rubber slip over type for old metal. Two (2) inch outside diameter. If car doesn't have old metal, see our #60-0322-21.