Search Results
Window Felt and Run Channel Set
p/n: 90-0140-58
This eight (8) piece Window Felt and Run Channel set includes the inner and outer window felts, upper rigid run channels, and flexible run channels needed to complete two doors. The set can be used for front or rear doors in models with vent windows in the door.
Front Door Weatherstrip Kit
p/n: 90-0100-72
Front door weatherstrip. This set is the primary seal for the door to the body. Set includes the door perimeter weatherstrip and the door bottom weatherstrip. Enough for two (2) doors. Includes fasteners.
Front Door Vent Window Set
p/n: 90-0374-90
This front door vent window weatherstrip set is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Engine Mount Service – Revulcanization Only
p/n: 60-0224-11
This Revulcanization Service Only is designed to restore your Side Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Transmission Support Mount - Revulcanization Service Only
p/n: 60-0315-25
This Revulcanization Service Only is designed to restore your Transmission Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Engine Mount Service – Revulcanization Only
p/n: 60-0296-11
This Revulcanization Service Only is designed to restore your Front Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Front Door Vent Window Weatherstrips
p/n: 38-0029-55
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Ferrule installing tool
p/n: 70-0662-69
Installing tool, door and trunk handle ferrule. For cars and trucks using door and trunk handle ferrules such as our #70-0111-69.
Rear spring bumper
p/n: 60-0179-35
Bumper, rear spring on frame. Entire assembly with rubber vulcanized to steel as original.
Windshield Gasket
p/n: 60-0198-50
This Windshield Gasket mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rear Window Gasket
p/n: 60-0199-81
This rear window gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Trunk Weatherstrip
p/n: 70-0083-85
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Transmission Support Mount - Revulcanization Service Only
p/n: 60-0530-25
Insulator - Plate Assembly - Guide for transmission support bracket. This Revulcanization Service Only is designed to restore your transmission mount to a like new original condition. Please call or email for more service details and ordering.
Fender welting 1/4" bead 50ft
p/n: 70-1098-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five
Fender welting 50ft chrome
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Fender Welting with 3/16 Bead - 50 Ft. Roll
p/n: 70-1100-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching four (4) fenders to body. Sold in a 50 foot roll.
Front spring bumper
p/n: 60-0021-35
Rebound bumper, front spring and rear spring for beam axle cars, steel ring reinforced as original.Height: 2.4375 inches.
Windshield Division Bar Gasket
p/n: 70-0159-51
Gasket, windshield division post, inner and outer, also acts as retainer for outer division bar chrome, molding.
Fenderskirt edge seal
p/n: 60-0298-45
Seal, wheel streamliner (fenderskirt) to fender. Two (2) strips each cut five (5) foot long.Length: 60.0 inches. Width: .625 inches.
Hood to Radiator Weatherstrip
p/n: 60-0110-42
This Hood to Radiator Weatherstrip is sold as a pair for the right and left. Overall length is ten and seven-eighths (10-7/8) inches. Made of top quality rubber to ensure durability and proper seal.
Front bumper grommet
p/n: 70-1104-28
Grommets, front bumper. Fully molded rubber. Two and one half inches (2-1/2") outside length by one and five sixteenths inch (1-5/16") outside width by one and eleven sixteenths inch (1-11/16") inside hole length by nine sixteenths inch (9/16") inside hol
Rear bumper grommet
p/n: 60-0143-28
Grommets, rear bumper, curved for good fit. Fully molded rubber. Three and eleven sixteenths inch (3-11/16") outside length by two and three sixteenths inch (2-3/16") outside width by one and eleven sixteenths inch (1-11/16") inside hole length by nine si
Brake and Clutch Pedal Pads
p/n: 60-0068-22
Brake and Clutch Pedal Pads - The proper design and fully detailed with ribs extending down over sides of the pad. Length: 3.50 inches. Width: 2.0 inches.
Steering column grommet
p/n: 60-0015-36
Grommet, steering column-to-floor, inner. Black. Brass core as original.
Access hole plug
p/n: 60-0016-24
Cover, brake master cylinder filler and inspection hole. Metal core as original.
Headlight mounting pad
p/n: 60-0413-14
Pad, headlight support bracket. Two (2) required per car.Length: 9.50 inches.
Door - Gravel Shield - Running Board Weatherstrip
p/n: 60-0054-73
This Door - Gravel Shield - Running Board Weatherstrip is a anti-squeak bulb type extrusion with fitment for General Motors vehicles. A twelve (12) foot strip made of high-quality EPDM dense rubber and designed from original parts for superior fitment, finish and function.
Parking light mounting pad
p/n: 60-0204-17
Mounting pad, accessory. Fender parking light.Length: 10.25 inches.
Rigid Run Channel
p/n: 70-0347-58
Stainless beaded edge, mohair-lined, exact replacement for rear side of division bar. Available in 15" pairs.
Bowtie emblem pedal pad
p/n: 60-0125-22
Pad, clutch and brake pedal, with Chevy bow tie in tread. Perfect copy, sharp detail.
Flexible Run Channel
p/n: 70-1239-58
Cloth covered, mohair lined flexible metal channel for sides and top of door windows.
Beltline Weatherstrip
p/n: 70-0555-58
This Beltline Weatherstrip is sold as a three (3) foot pair. The beltline is used for side window inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Vent division bar weatherstrip
p/n: 60-0596-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Hood to Radiator Weatherstrip
p/n: 60-0111-42
This Hood to Radiator Weatherstrip is molded with four (4) self retaining carrots for easy installation. Sold as a pair for the left and right sides.
Rear spring bushing
p/n: 60-0311-35
Bushing, rear spring front eye, inlox cartridge type as original.
Flexible Run Channel
p/n: 70-1238-58
Cloth covered, mohair lined flexible metal channel for sides and top of door windows.
Accelerator pedal pad
p/n: 60-0097-40
Pad, accelerator pedal. Slip-over type for original core.Length: 9.125 inches.
Fender welting 1/4" bead 25ft
p/n: 70-1097-44
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For
Fender welting 25ft chrome
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Accelerator rod seal
p/n: 60-0136-41
Grommet, accelerator rod through toe board. Brass core and center bushing as original.
Fender Welting with 3/16 Bead - 25 Ft. Roll
p/n: 70-1099-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching two (2) fenders to body. Sold in a 25 foot roll.
Front bumper seal
p/n: 70-1103-28
Seals, front bumper. Fully molded rubber, U-shaped. Three and one half inches (3-1/2") long by three and one half inches (3-1/2") wide by thirteen sixteenths inch (13/16") height. For the grommets see our #70-1104-28, sold separately.
Fuel Neck Grommet
p/n: 60-0040-41
Grommet, fuel filler neck. Fully molded rubber, slightly angled with retaining flange. Three and five sixteenths inch (3-5/16") outside width by three and one half inch (3-1/2") outside length by two and one eighth inch (2-1/8") inside hole diameter.
Side Window Sash Channel
p/n: 70-0641-58
Sash channel, side window glass. U-shaped steel channel only, no filler. Will require that you attach your own window regulator cam to underside as required.
Cowl vent weatherstrip
p/n: 70-0143-54
Gasket, cowl vent. Perfect copy of original, not a sponge substitute, top quality material.
Brake and clutch pedal bumper
p/n: 60-0024-24
Bumpers, brake and clutch pedal shank to floorboard. Rides pedal shank under floorboard. Compare to our #60-0104-24.Length: 1.8125 inches. Width: .
Horn button contact cushion
p/n: 60-0192-21
Cushion, standard steering wheel horn button contact. Two and one half (2-1/2) inch diameter.
Horn button contact ring
p/n: 60-0157-21
Ring, horn button contact. Accessory banjo steering wheel. Four and one eighth (4-1/8) inch outside diameter.