Washer, for attaching moldings, emblems, and fender guards as required on body.
Standard Bumper - Commonly used for fuel filler or glovebox doors.
Glovebox and Fuel Filler Door Bumper.
Bumper, anti-rattle. Door window garnish molding, stem type retainer.
Grommet, choke cable firewall.
Grommet, heater motor wire firewall.
Bumper, door check arm.
Grommet designed for electrical applications.
Washer, for attaching chrome moldings on body. Fits into metal cup retainer. Three fourths (3/4) inch diameter, use as required.
Washer, upper motor mount. Used on top.
Pad, glovebox door.
Grommet, choke and throttle cable.
Gasket, license plate light lens.
Bumper, hood, 2 uses. Hood to radiator shell at side panel, Hood to fender, as required.
Grommet to run headlight wires through inner wheelhouse panel.
Grommet designed to run the heater vent control cable through firewall brace.
Bumper, standard, self retaining.
Bushing, for double acting shock absorber arm link. Height: .78125 inches.
Clip, side window run channel retaining. Rust resistant spring steel.Width: .4375 inches. Height: .8125 inches.
Bumper designed for various uses.
Bumper, used at door opening at upper corner, license plate, and/or fuel filler door. Self-retaining type.
Clip, side window run channel retaining. Rust resistant spring steel. Compare with your original.Width: .4375 inches. Height: .9375 inches.
Bumper, trunk or hood. Molded with clearance for screw. Used for: Buick 1942-50 Bumper for trunk. Chevrolet 1949-55 Bumper for rear hood corners on cowl. Chevrolet 1949-50 Bumper for trunk. Oldsmobile 1938 Bumper under hood corner on radi
Plug, brake adjustment hole. Fits five sixteenths (5/16) inch by one (1) inch slot. Most models with drum brakes.Length: 1.25 inches. Height: .875 inches.
Bumper designed for various applications.
Grommet to run wiring harness through fender skirts or hood latch lower mounting panels.
Plug, cowl and floor pan. Three fourths (3/4) inch.
Bumper, hood to cowl and door hinge pillar upper.
Grommet designed to run the windshield wiper control cable or gas gauge wire through rear compartment pan.
Grommet, electrical wires (various). Sheet Metal Hole: 1/2" Center Hole: 1/4" Outside Diameter: 3/4" Slot Width: 1/16"
Bumper, hood rest, cap type for adjustable screw, fifteenth sixteenths (15/16) inch, seven sixteenths (7/16) inch thick.
Grommet, insulator for gearshift control rod.
Grommet, hood pull cable firewall.
Plug, cowl and floor pan. This body plug covers a sheet metal hole that is one and one fourth (1-1/4) inch in diameter.
Gasket, license plate light lens to housing.
Plug, hole in dog leg cover. Installs at front of door where bolt to adjust vent window frame is located. This body plug covers a sheet metal hole that is one and one half (1-1/2) inch in diameter.
Plug designed for floor and drain holes.
Bumper, license plate to trunk lid.
Pads, license plate bracket to trunk lid.
Seal, heater tube to firewall.
Seal, front suspension outer upper arm. Four (4) required per car.
Grommet for parking brake release rod.
Plug designed for various uses.
Bushing, shock absorber link. May be used for front or rear spring.Chrysler 1951-54 Bushing, rubber, shock absorber link.
Insulator (bushing). Gearshift selector rod.
Sash channel weatherstrip. Available by the foot.
Bushing, shock absorber mounting. Double cone style, rear. Five eighths (5/8) inch hole, one and one sixteenths (1-3/16) inch outside diameter, three fourth (3/4) inch thick.